
UL 10C fire-tests complete door assemblies under positive pressure. The lesson for smart locks is strict: only hardware named in the listing belongs on a labeled fire door.
UL 10C, Standard for Safety for Positive Pressure Fire Tests of Door Assemblies, is the fire test most North American specifiers mean when they call a door “UL fire-rated.” A complete assembly — door leaf, frame, hinges, locks, strikes, closers, seals, glazing and even the wall construction — is mounted in a furnace and exposed to a controlled positive-pressure time-temperature curve, followed by a hose-stream exposure for rated assemblies. Ratings are expressed in minutes or hours such as 20/45/60/90 minutes or 3 hours. The consequence for access control is structural, not cosmetic: a lock, electric strike, maglock or smart escutcheon may be installed on a labeled door only when it is part of, or explicitly allowed by, the listing, and immediate free egress is non-negotiable. This guide explains how UL 10C testing works, how listed hardware is identified, and how our factory supports fire-door projects with named-SKU documentation per quotation.
| What it tests | Complete door assemblies in a furnace under a positive-pressure fire curve, with hose-stream exposure for rated assemblies. |
| Ratings | Time-based labels such as 20, 45, 60, 90 minutes or 3 hours, tied to wall categories and the certified configuration. |
| Assembly principle | Every hinge, lock, strike, closer, seal and glass light is part of one tested assembly; the label governs what may be installed. |
| Allowed hardware | Only listed or classified hardware for use on fire doors, installed per its listing and the door manufacturer’s instructions. |
| Electrified devices | Electric strikes, electrified trim, holders and maglocks must be listed for the use, with fail behavior and egress logic matching code. |
| Free egress | Occupants must exit without keys or special knowledge; panic hardware rules add on where required by occupancy. |
| Field changes | Drilling, swapping strikes or adding unlisted devices voids the rating; modifications require a listed method or relabeling. |
Acceptance is administrative as much as technical: the device must appear in the assembly documentation, install exactly as listed, and leave free egress intact. A strong lock that is not listed is simply not an option.
| Requirement | What it means | How it is evidenced |
|---|---|---|
| Listing coverage | The lock or strike is named for fire-door use with a recognized listing. | Listing card and door manufacturer approval. |
| Correct category | The device suits the door rating and category (A, B, E and similar frame uses). | Cross-check listing against the door label. |
| Free egress | Inside operation opens the door with one motion, no key. | Hardware schedule and on-site egress test. |
| Fail behavior | Electrified parts release or secure as the listing and code require. | Wiring diagram plus AHJ approval. |
| No field alteration | No extra holes, wraps or unlisted accessories on the leaf. | Installation photos and inspection records. |
| Documentation chain | Door label, hardware labels and submittals tell one story. | O&M manual with all listing references. |
Fire doors appear across commercial projects, but the hardware duties differ by location. Corridors, stair enclosures and cross-corridor smoke barriers each have their own label category and review depth.
| Opening | Typical door | Lock approach |
|---|---|---|
| Stair enclosure doors | Listed lock or exit device, often 90-minute or 2-hour assembly | Egress hardware and fail logic receive the closest review. |
| Corridor and room doors | 20/45/60-minute labels per occupancy | Smart locks must be listed for the exact door category. |
| Cross-corridor smoke barriers | Holders and closers coordinated with fire alarm | Electromagnetic holders release on alarm automatically. |
| Healthcare patient areas | Listed hardware with clinical locking functions | Free egress rules still dominate over security needs. |
| Storage and plant rooms | Rated doors with listed locks or panic devices | Self-closing and latching must remain functional. |
| Retrofit situations | Only listed swap-in hardware for the assembly | Unlisted electronic additions void the door rating. |
For named SKUs intended for labeled openings, our quotation pack below supports the design team and the authority having jurisdiction. Models not covered for fire-door use are identified in writing rather than left ambiguous.
| Component | Typical logic | Notes |
|---|---|---|
| Hardware listing evidence | Recognized listing showing the lock or strike for fire-door use. | First document the AHJ will request. |
| Door assembly cross-reference | Which door and frame constructions accept the device. | Designer matches it to the door label category. |
| Egress and wiring narrative | How free egress and power failure are handled. | Goes into the fire alarm and access-control drawings. |
| Installation instructions | Listed mounting method with permitted holes and screws. | Protects the rating during installation. |
| Written scope letter | Which quoted SKUs are fire-listed and which are not. | Prevents accidental substitution during procurement. |
UL 10C tests the complete door assembly — leaf, frame, hinges, sealing, glazing, closers and hardware — installed in a representative wall. A lock is therefore not “UL 10C certified” as a standalone product in the way a power tool carries a safety listing; rather, it is listed or classified for use on fire doors, and the door assembly is tested with hardware like it. Procurement asks two questions: is the lock recognized for fire-door use, and does the specific door manufacturer allow it in the rated assembly? Both answers must be yes, in writing.
Older fire tests (such as UL 10B) used a neutral-pressure profile, while UL 10C applies positive pressure across the door face, closer to real fire dynamics in modern buildings. Under positive pressure, hot gases push against gaps at the top and edges, so the assembly is challenged more severely there, and door position, sealing and hardware performance matter. Most current US codes accept or require UL 10C for swinging fire door assemblies; older inventory may carry 10B labels, and the authority having jurisdiction decides what is acceptable on a given project.
Only with hardware listed for that assembly and installed exactly per the listing. Electric strikes on fire doors must be the fire-listed model with the correct frame category, monitored or fail behavior as required, and often a specific mounting and wiring method. Surface-bonded readers and magnetic contacts can also interfere with closing and clearances. Drilling new holes, taping latches, shimming strikes or adding maglocks without listing approval voids the rating and creates liability. When in doubt, the door manufacturer or an accepted modification program should authorize the change in writing.
Free egress means anyone inside can leave with one straightforward motion, without a key, credential or special knowledge. A mechanical lever or crash bar that retracts the latch mechanically satisfies this on most electrified locks; fail-secure electric latch retraction is acceptable only when inside egress remains fully mechanical. Magnetic locks require listed releasing arrangements, such as panic hardware with an integrated switch or ceiling-mounted request-to-exit sensors with a set time delay, and the authority having jurisdiction must accept the sequence. Battery-powered smart locks typically retain mechanical egress by design, but the model still has to be listed for the door.
Ratings run from 20-minute smoke-and-draft-control assemblies through 45, 60 and 90 minutes to 3 hours, but specifying “the highest” is wrong: the code and the wall’s own rating determine what is needed for each opening. A 1-hour wall commonly requires a 45-minute or 1-hour door depending on occupancy and configuration; stair and shaft enclosures often need 90 minutes or 2 hours; 20-minute doors appear in corridor and smoke partition roles. The architect sets the label; the hardware team then selects listed locks that fit, rather than choosing hardware and hoping the label accommodates it.
Share the door labels and opening schedule. We identify which quoted SKUs are listed for fire-door use, provide listing references and egress narratives, and state scope limits in writing.
Request Spec Sheet + QuoteCertifications overviewLast updated: October 31, 2026 · Reviewed by the Smart Lock Factory editorial team