
Solid wood, veneered and composite wooden doors accept different lock bodies. This guide maps core type, thickness and existing prep to the right smart lock family.
Wooden doors are forgiving to modify but inconsistent in construction: a 45 mm solid oak entrance door and a 35 mm hollow-core veneer room door cannot share the same lock assumption. Smart lock fit on timber depends on four measurements — total thickness, stile width, backset and the existing lock pocket — plus whether the door is solid, veneered, MDF-wrapped or honeycomb-filled. Our factory supplies mortise, cylindrical-deadbolt and surface-mounted smart locks for wooden doors, and confirms the exact fitment in writing per door schedule before tooling or shipping. This page explains which body suits which wooden door, where reinforcement is needed, and what photographs and measurements we require for a written fit confirmation.
| Door thickness | Most smart lock bodies cover 35–60 mm timber; doors outside this range need spacers, longer tail bars or a different family, confirmed per quotation. |
| Core types | Solid timber and solid-core doors take full mortise bodies; thin veneer and hollow-core doors need reinforcement plates or surface-mounted locks. |
| Stile width | Narrow stiles below roughly 100 mm constrain rose and keypad size; a photograph with a ruler prevents oversized escutcheons. |
| Existing prep | Existing mortise pockets, cylindrical bores or rim holes are usually reused rather than re-cut, preserving fire and warranty performance. |
| Reinforcement | Long screws, strike plates and reinforcement kits are specified for softwood, MDF and veneered cores where lever or pull forces are high. |
| Handing | Left/right and inward/outward opening are confirmed from photos; many bodies are field-reversible but cylinders and latches are ordered to hand. |
| Confirmation | A door schedule plus front, edge and strike photos receives a written model-level fit check before deposit. |
Reuse the existing cut-out wherever possible: mortise prep gets a smart mortise, a cylindrical bore gets a smart deadbolt, and a door that must not be cut gets a rim or retrofit model.
| Existing door prep | Typical wooden door | Recommended smart lock path |
|---|---|---|
| Mortise pocket | Apartment or hotel solid-core door with a full mortise body | Smart mortise lock reusing the pocket and strike; tail bars cut to door thickness |
| Cylindrical bore | Residential solid-wood entrance with 54/57 mm backset bore | Smart deadbolt or lever replacing the existing cylindrical lock, minimal new routing |
| Rim / night latch | Older timber entrance door with a surface box | Smart rim lock on the door face, no new mortising, reinforcement plate under screws |
| Euro pocket | Imported timber door already cut for a Euro cylinder | Electronic Euro-profile cylinder or escutcheon over the existing prep |
| No existing prep | New-build door in production | Factory-prefitted lock body before hanging, aligned to the door line |
| Uncertain prep | Renovation door with patched or hidden pockets | Photo review first; test-fit sample recommended before volume order |
The door schedule should separate structural entrance doors from lightweight interior timber, because the allowed lock mass and screw load differ significantly.
| Opening | Typical door | Lock approach |
|---|---|---|
| Main entrance | 40–55 mm solid timber or solid-core | Smart mortise or deadbolt with reinforced strike; weather gasket if exposed |
| Apartment unit | 38–50 mm fire-rated timber where specified | Mortise body matching the fire schedule; free-exit always preserved |
| Hotel room | Solid-core veneered door, uniform prep | Smart mortise family standardized across floors for keying consistency |
| Office interior | 35–45 mm veneer or MDF-wrapped | Light smart lever or Euro escutcheon; reinforcement plate if stile is soft |
| Bedroom / storage | Honeycomb or hollow-core timber | Surface rim lock or reinforced prep; avoid heavy pull-handle bodies |
| Gate-style timber | Thick hardwood exterior gate 60 mm+ | Weather-rated rim lock with longer fittings and drainage, confirmed per drawing |
This example illustrates a typical configuration, not a specific customer project. Core mix and existing prep drive the model split.
| Component | Typical logic | Notes |
|---|---|---|
| Entrance smart locks | Mortise or deadbolt bodies for solid entrance doors | Finish and thickness set confirmed per quotation |
| Interior smart levers | Lighter escutcheons for veneered office and room doors | Reinforcement plates added for soft cores |
| Cylinders and tail bars | Ordered to each measured door thickness and hand | Long-tail cutting service available for mixed schedules |
| Reinforcement hardware | Strike boxes, long screws and mounting plates | Specified where core strength is uncertain |
| Sample fit lot | One representative lock per door type before volume | Current MOQ and sample policy confirmed in writing |
It can, but the fitment differs from a solid door. A hollow or honeycomb core has little material to hold mounting screws, so a heavy full-mortise smart lock can loosen over time. We typically recommend a lighter escutcheon over an existing Euro prep, a surface-mounted rim lock, or a reinforcement plate spread across the stile. Life-safety doors must keep their certified assembly unchanged regardless of core. For multi-door projects, send one representative door for sampling rather than assuming the spec from the face veneer; the written fit confirmation is issued against the actual door, not the product description on the purchase order.
Our first choice is to reuse the existing pocket, bore and strike because it preserves door strength and any fire performance. A smart mortise with the same or a covered footprint drops into many standard preps; a smart deadbolt replaces a cylindrical bore without new routing. When the old pocket is larger or misaligned, an adapter plate or escutcheon covers the difference instead of fresh chiseling. If new cutting is genuinely required, it is done by qualified installers and never on a fire-rated assembly outside its certified configuration. Every exception is recorded in the door schedule.
Most standard bodies cover timber doors from about 35 to 60 mm using adjustable tail bars and mounting posts. Thinner veneer doors risk posts and bolts protruding, while gates and solid hardwood doors above 60 mm need extended components or a surface-mounted design. Thickness is measured at the lock line, not at the raised panels, and an edge photograph with a ruler is the fastest way to confirm. Where a building mixes 38 mm interior doors with 50 mm entrance doors, the cylinder and tail list is cut to the measured set rather than ordered as one length.
Fire-rated timber doors must retain the hardware configuration listed in their certification. Where electrified or electronic locking is allowed, the selected smart lock is matched to a door-and-hardware schedule that has been assessed for that rating, and free egress is always mechanical and immediate. We supply hardware against the written schedule and provide the relevant documentation packs for the models involved; we do not field-approve modifications on site. Installers and specifiers hold responsibility for the local approval path, which commonly involves UL 10C or EN 1634 evidence depending on market.
The standard path is a door schedule, photographs and a small sample lot. The schedule lists thickness, core type where known, existing prep and handing; photos show the face, edge pocket and strike with a ruler; we then return a written model-by-model fit map. One lock of each type is fitted to a representative door — often on site or at the door manufacturer’s line — before production release. This catches long tails, oversized roses on narrow stiles and weak cores while correction is cheap. MOQ, lead times and sample terms are confirmed in writing per quotation.
Send the door schedule and prep photos — receive a written model-level fit map with sample, MOQ and lead-time terms.
Discuss your project (RFQ)Project configurationsLast updated: October 31, 2026 · Reviewed by the Smart Lock Factory editorial team