Slk 9905a door fit notes: use this SLK-9905A door fit checklist to verify door thickness, mortise details, hardware clearances and replacement scope.

Opublikowano: cze 20, 2023

Replacing Doors or Locks with SLK-9905A: A Fit Checklist

Replacing Doors or Locks with SLK-9905A: A Fit Checklist

Procurement managers use the slk 9905a door fit notes to separate an apparent lock replacement from a verified fit. The decision may involve retaining the door leaf, replacing the lock, or replacing both. Visual similarity is not enough: the door thickness, lock case, cylinder interface, spindle, strike, retained hardware and access-management requirements must all be reconciled.

Direct answer. In brief, this article covers slk 9905a door fit notes from slk 9905a door fit notes to slk-9905a. It states what to confirm about slk 9905a door fit notes on the dated product page where a figure is involved. A slk 9905a door fit notes is a component-level look at how the technology behaves. slk 9905a door fit notes is where the limits sit. slk 9905a door fit notes is verified on the dated product page.

Read slk 9905a door fit notes as slk 9905a door fit notes. It is a working definition of slk 9905a door fit notes. Not a statutory or certified one. It applies to the market and product in question rather than as a general claim.

The published SLK-9905A record identifies it as an RFID hotel lock with a hidden card reader. It lists hotel wooden and metal doors, a 38–100 mm door-thickness range and a 7-pin high-security profile cylinder. It does not provide a complete dimensional drawing in the supplied catalogue entry, so those figures do not establish that every hotel lock of similar appearance can be exchanged. Confirm on the dated product page for the specific SKU and obtain the applicable dimension drawings before releasing a project order.

Clause 1 — Define which part of the opening is being replaced

A fit review becomes clearer when the buyer names the replacement boundary before comparing products. “Replace the lock” can mean exchanging only the visible panel while leaving the lock case, cylinder, spindle and strike in place. It can also mean installing a new lock case and related hardware in the existing leaf. A full door replacement changes the frame, rebate, handle, seal and site-access work as well as the lock.

Use this clause to assign one scope code to every door in the schedule:

Scope codeParts retainedParts replacedRequired starting evidence
ADoor leaf and principal hardwareLock assembly and affected interfacesExisting door measurements and photographs
BDoor leaf and lock casePanel, cylinder and affected interfacesLock-case and cylinder drawings
CPrincipal site worksDoor leaf, lock assembly and affected hardwareNew-door drawings and site opening schedule
DUndecidedUndecidedEvidence-gathering inspection required

Do not assign scope from the model number alone. A door marked for scope A can become scope B if the existing mortise case does not match the dated SLK-9905A drawing. A door marked for scope C can return to scope A if the replacement leaf arrives with compatible interfaces and the project accepts that finish.

Clause 2 — Freeze the catalogue baseline before the site inspection

The baseline gives inspectors the same starting facts for every door. The supplied catalogue record lists the SLK-9905A as an RFID/IC card hotel lock using Mifare-1 13.56 MHz cards. Its platform is hotel lock management software with a PC encoder and guest cards. The recorded network arrangement is a standalone lock with a PC-linked card encoder, and no in-room network is required.

Baseline itemPublished SLK-9905A recordUse in the fit decision
Door thickness38–100 mmCompare with measured leaf thickness; do not infer from door width
Door typeHotel wooden / metal doorsConfirm the actual leaf and frame construction
Cylinder7-pin high-security profile cylinderCheck the existing cylinder interface, not only the keyway appearance
AccessRFID/IC card: StandardConfirm the card platform required at the property
Management arrangementPC encoder, guest cards and standalone lock operationCheck whether existing access administration must continue
PowerFour AA alkaline batteries with low-battery alertConfirm battery access and maintenance ownership
FinishSatin nickel or powder blackRecord the selected finish and obtain a physical reference where needed
DocumentationDrawings, installation guide and datasheet available on requestObtain the exact revision used for approval

For the wider specification record, read SLK-9905A: Reading the Published Specification Without Guesswork. It complements this handbook by showing which catalogue fields are useful facts and which missing fields must still be sourced.

Clause 3 — Choose the replacement route with a recorded gate

The replacement route should follow a simple sequence. First establish whether the leaf will be retained. Then measure the door and its interfaces. Compare those measurements with the dated drawings. Only after that comparison should a sample move into an installation test.

flowchart TD
    A[Lock the replacement scope] --> B{Retain the existing door leaf?}
    B -- Yes --> C[Measure leaf frame and retained hardware]
    B -- No --> D[Obtain new leaf and frame details]
    C --> E{Dated drawing matches site evidence?}
    D --> E
    E -- Yes --> F[Move to sample fit check]
    E -- No --> G[Open and assign a fit exception]
    G --> F

This gate produces three outputs rather than an informal yes or no:

  1. Accepted route: the selected scope agrees with the dated drawing, the site record and the physical sample.
  2. Conditional route: the fit can proceed only after a named exception receives written evidence and approval.
  3. Rejected route: the proposed interface cannot be reconciled without changing the door, lock case or retained hardware.

For a hotel lock retrofit, retain the completed site record rather than a cropped lock photograph. A photograph may conceal the frame rebate, keeper position, door thickness or the path required for the concealed reader. The Smart Lock Retrofit Site Survey process is useful for establishing the survey scope, while this checklist adds the SLK-9905A-specific interfaces that must appear in the final evidence package.

Clause 4 — Measure the hotel wooden door or metal door leaf

The recorded 38–100 mm range is a screening boundary, not a complete installation drawing. Record the actual thickness at several points and explain any variation rather than selecting the largest reading. Also identify whether the leaf is wooden or metal because the catalogue names both as suitable door types, but that does not remove the need to inspect construction, reinforcement and fixing conditions.

A site measurement record should contain the following fields:

MeasurementHow to record itAcceptance basis
Leaf thicknessRecord actual readings at hinge, middle and latch positionsMust fall within the range shown on the dated SKU drawing
Leaf width and heightRecord overall dimensions and any unusual shapingUsed to check handle, reader and frame clearance
Material and buildIdentify the hotel wooden door or metal door constructionSupplier confirms suitability from the site description
Frame rebateRecord depth, width and any uneven sectionCompare with the lock case and strike drawing
BacksetMeasure from the door edge to the lock-case reference pointDo not adopt a value inferred from a visual template
Fixing positionsMark and photograph existing lock and strike fixing pointsCompare centres and tolerances with the drawing
Door swing and handingRecord hinge side, opening direction and handingConfirm the correct lock orientation
Reader routeNote available face, reveal and routing spaceConfirm the hidden-reader position before fabrication

Do not approve a leaf merely because its nominal size appears familiar. An unusual rebate, shallow lock edge, reinforced metal face or irregular frame can change the required work.

Clause 5 — Reconcile the mortise case and cylinder interface

The catalogue identifies a 7-pin high-security profile cylinder for the SLK-9905A. An existing cylinder with a similar visible profile can still differ in its case interface, cam arrangement, fixing method or relationship to the mortise case. The buyer therefore needs more than a photograph of the keyway.

Request the following evidence for each retained or replacement lock case:

InterfaceEvidence requiredAction when evidence conflicts
Mortise caseDimensioned drawing and physical measurementChange the lock-case scope
Cylinder profileCylinder drawing and existing case measurementRetain the case only if the interface is confirmed
SpindleSpindle position, section and engagement detailsSelect an approved alternative or revise the door
Cylinder fixingFixing centres and attachment methodReconsider the retained case or cylinder
Lock-case edge distanceMeasured distance from door edge to caseCompare with the dated drawing
Strike positionFrame keeper location and fixing centresAdjust scope or frame work
Bolt or latch travelExisting case movement and projectionVerify operation with the selected door

Clause 6 — Test the hardware system around the lock

The lock operates within a hardware assembly rather than in isolation. Latch or deadbolt travel can be affected by the strike plate and keeper. Lever or handle clearance can depend on the escutcheon position. A door closer or hold-open device can alter the force through the latch, while an escape device imposes a separate operating requirement.

Ask the site team to mark each retained item on the door record:

ComponentFit questionRequired evidence
Latch or deadboltDoes the selected mechanism meet the existing door edge and keeper arrangement?Case drawing, edge measurement and operating test
Strike plateAre the opening, fixing centres and keeper position compatible?Marked strike photograph and dimensions
Strike keeperIs the frame material and reinforcement adequate for the proposed fixing?Frame inspection record
Lever or handleIs there sufficient internal clearance and correct spindle engagement?Handle measurement and sample operation
Door closerCan the door close normally with the lock installed?Closer adjustment record and test result
Hold-open deviceDoes the latch remain compatible with the selected hold-open arrangement?Written arrangement and operating test
Escape deviceDoes the lock and handle arrangement preserve the intended escape movement?Site-team verification and test record
Concealed readerIs the chosen position reachable and consistent with the door construction?Marked reader location and routing plan

Where the property or project imposes a requirement concerning door operation or escape hardware, request the written requirement and the evidence it requires. Do not infer compliance from the catalogue record.

CONFIRM-WITH-LOCAL-SITE-TEAM: Confirm any project-specific door, escape-hardware or access-control requirement before approving the retained hardware arrangement.

Clause 7 — Check power and credential-management dependencies

Physical fit does not end at the door face. The published SLK-9905A record lists four AA alkaline batteries and a standard low-battery alert. At the door, that means the installation team must have a defined way to access and service the battery compartment without damaging the panel or finish. Record the proposed battery-change route and who will own the maintenance task.

DependencyBuyer questionAcceptance evidence
Card standardAre the required guest and staff cards based on the recorded Mifare-1 13.56 MHz arrangement?Card sample and written platform confirmation
EncoderWhere will the PC-linked card encoder be installed and connected?Equipment schedule and tested issuance workflow
Guest-card issuanceWho issues, cancels and recovers cards?Named process and responsible role
PermissionsHow will floor and room permissions be assigned?Tested permission example
Validity windowsHow will check-in validity windows be configured?Approved workflow and test record
Unlock recordsWhich records must be retained and reviewed?Confirmed report requirement
In-room networkIs the stated no-in-room-network arrangement appropriate for this project?Signed system-scope decision
BatteriesWhere will four AA alkaline batteries be accessed and replaced?Maintenance instruction

For the wider management decision, use Configuring SLK-9905A: Credential Choices and Management Tools. Keep that software review connected to the door record because a credential decision can change the panel configuration, reader position, encoder requirement and replacement boundary.

The catalogue fields establish a starting scope; they do not replace a project-specific interface test.

Clause 8 — Mark environmental uncertainty instead of assuming

The environment field in the supplied SLK-9905A catalogue entry is an em dash. In other words, the published record used for this handbook does not state an operating temperature range, humidity range or weatherproof-housing specification for this SKU. Those capabilities must not be inferred from the broader catalogue.

That absence matters when a hotel lock is considered for an exterior door, a sheltered entrance, a washdown area or another non-standard location. Record the actual exposure rather than relying on the room label. Include whether rain reaches the face, whether cleaning water collects around the panel, whether the door faces direct sunlight, whether salt or industrial atmosphere is present, and whether the reader position is exposed.

Site conditionRequired questionDisposition if unanswered
Interior controlled openingIs normal indoor operation the intended scope?Record the site condition and supplier confirmation
Exterior or sheltered entranceWhat exposure does the face and concealed reader encounter?Keep environmental suitability open
Washdown or cleaning exposureCan water enter the reader, cylinder or battery area?Obtain specific guidance before approval
Direct sunlightIs there a stated temperature range for the selected configuration?Do not infer suitability from another model
Metal door in a coastal settingWhat site-specific exposure applies?Require written project guidance

Clause 9 — Account for the packing and project-order boundary

The catalogue gives the SLK-9905A export-carton record as 485 × 330 × 445 mm, with six units per carton and a gross weight of 16.1 kg. These figures help procurement plan receiving space, carton handling and the movement from storage to the floor. They do not prove that a replacement will arrive as one complete unit; the required project configuration still has to be stated in the order.

Published packing fieldRecorded valueProcurement implication
Carton dimensions485 × 330 × 445 mmCheck receiving and storage clearance
Units per export carton6 pcs/ctnUse only as a packing reference, not a project-order quantity
Gross weight per carton16.1 kgConfirm handling arrangements at the delivery point
ConfigurationCustom logo, finish, packaging, manuals and product configuration for distributor and project ordersDefine the exact configuration in the order file
DocumentationDimension drawings, installation guide and full datasheet available on requestAttach or reference the approved document revisions

The SLK-9905A Order Checklist for Project and Repeat Purchases provides the order-side sequence. Add the door-specific drawings and exception status from this fit handbook so a repeated purchase is based on an approved configuration rather than a copied model name.

Clause 10 — Assemble one auditable fit-evidence package

Evidence recordRequired contentsPass condition
Door scheduleDoor identifier, location, scope code and hardware statusOne scope assigned to each door
Measurement sheetThickness, rebate, backset, fixing centres and door constructionMeets the released drawing or has an assigned exception
Photo setFull door, lock edge, frame, strike, handle and retained devicesImages are legible and tied to the door identifier
Dated SKU recordCurrent model record and configuration referenceMatches the item being evaluated
Dimension drawingDoor-fit and lock-interface drawingCorrect revision approved by the project team
Installation guideRelevant installation steps for the configurationRevision recorded in the fit file
DatasheetPublished specification and environmental entriesMatches the selected configuration
Hardware scheduleRetained and replaced componentsNo unassigned interface remains
Sample-fit recordInstallation and operating observationsAll mandatory checks accepted
Exception logOpen issue, owner, evidence and dispositionNo unapproved blocker remains

Clause 11 — Run the representative sample before the wider

A sample fit check should use a representative door rather than the most convenient opening. Select a door that includes the most demanding retained hardware or construction condition identified in the survey. If several door types exist, use separate samples or separate test plans for each type.

Use this sequence for the sample:

  1. Check the leaf, frame, lock case and strike against the released drawing before applying finish.
  2. Install the lock case and cylinder while retaining access to the spindle, cylinder fixing and case fixing.
  3. Confirm the concealed-reader position and the available routing path against the approved door drawing.
  4. Fit the panel, handle or lever and check free movement without forcing the door.
  5. Install or retain the closer, hold-open and escape devices in their intended positions.
  6. Test latch and bolt operation with the door closing under normal conditions.
  7. Connect the specified encoder and management arrangement, then issue and test the required card types.
  8. Verify guest-card issuance, the relevant permission, validity-window operation and unlock-record retrieval.
  9. Record battery-compartment access and the low-battery alert procedure.
  10. Photograph the completed installation and update the exception log.

Do not use a successful card unlock as proof of a complete fit. Mechanical movement, frame clearance, retained devices, reader routing and record retrieval each need their own evidence. Conversely, a clean visual installation does not establish that the management arrangement works.

Clause 12 — Code exceptions so they cannot disappear

CodeTriggerInitial dispositionEvidence required to close
F-01Door thickness or construction is unresolvedConditionalMeasurement sheet and supplier confirmation
M-01Lock case, spindle or cylinder interface conflictsConditional or rejectedDated drawing and approved case comparison
B-01Backset or fixing centres cannot be reconciledConditionalDoor measurement and revised fit method
H-01Retained closer, hold-open or escape device interferesConditionalMarked hardware test and site approval
S-01Strike or keeper arrangement is unsuitableConditionalFrame measurement and operating result
P-01Battery access or power arrangement is unclearConditionalMaintenance record and panel-access check
R-01Reader position or routing is unavailableConditionalApproved reader layout and sample result
C-01Card or management workflow is unresolvedConditionalEncoder and credential test record
E-01Environmental exposure is outside the documented evidenceUnresolvedSpecific dated guidance for the SKU
D-01Drawing, guide or datasheet revision is missingUnresolvedControlled document set
F-02Selected finish is unavailable or unconfirmedConditionalFinish confirmation and reference sample

A conditional approval should identify the condition, not merely state “subject to fit.” It should state what evidence closes the issue and who signs the closure. If an exception changes the replacement scope, revise the door schedule and the affected commercial request before proceeding.

Clause 13 — Gate the release of replacement hardware

Release controlProcurement checkRequired sign-off
Door scopeEvery door has scope A, B, C or DSite team
MeasurementRequired fields are completeInstaller or site inspector
SLK-9905A configurationSKU, finish and configuration are identifiedProcurement and supplier
Drawing controlCurrent drawing, guide and datasheet are referencedTechnical reviewer
HardwareRetained and replaced components are listedInstaller
Credential planEncoder, cards and records have named ownersAccess-management owner
SampleRepresentative fit test is acceptedTechnical reviewer
ExceptionsBlockers are closed or formally declinedAuthorised project approver
Order referencesPurchase record points to the approved fit packageProcurement
Installation handoverInstaller receives the same controlled revisionSite team

A bulk replacement should not proceed from a successful sample of one door type when another type has a different leaf, strike or retained-hardware arrangement. Group doors by physical configuration, test each group and identify which sample represents it. That method makes the approval traceable without assuming that all hotel wooden doors share one installation condition.

Clause 14 — Write the door information into the request-for-quote

A useful RFQ gives the supplier enough information to return a relevant configuration and identify unresolved interfaces. The Office Smart Lock Site Survey shows how to organise the site-record side of the review; the project-specific fields below add the SLK-9905A replacement decision.

RFQ fieldInformation to include
Intended configurationSLK-9905A, selected finish and project scope
Door populationDoor identifiers, quantities and physical types
Leaf measurementActual thickness, rebate, backset and fixing positions
Door constructionHotel wooden door or metal door description
Existing lockCase, cylinder, spindle, handle, latch and strike arrangement
Retained hardwareCloser, hold-open and escape-device details
Reader arrangementRequired concealed-reader location and routing information
Management requirementEncoder, card, permission and unlock-record needs
EnvironmentExposure at each representative door location
Document requestDimension drawings, installation guide and full datasheet
Sample requestRepresentative-door fit test and documentation
Commercial referenceThe approved fit-package reference

Clause 15 — Preserve a handover record at the installed door

The handover should preserve the decisions that made the installation workable. Store the approved drawing, measurement sheet, exception closure and relevant installation reference with the building’s maintenance record. Identify the lock configuration and selected finish in the asset register so a later replacement does not start from the original uncertainty.

Use the handover sequence below:

StageRecord to complete
Before installationVerify the door identifier, document revision, configuration and retained hardware
During installationRecord removed parts, installed parts, adjustments and reader routing
At commissioningRecord card test, permission test, unlock-record test and mechanical operation
After adjustmentRecord closer interaction, handle movement and any modified hardware arrangement
At acceptanceAttach the approved fit package and close the exception log
For future maintenanceLink the asset record to the configuration, finish and controlled documents

A future installer should be able to understand why a particular lock case, strike, reader position or door preparation was accepted. That history is particularly valuable when the project later changes from lock replacement to full door replacement, or when a repeated purchase uses the SLK-9905A across several properties.

The same question is worked through in more detail in narrow edge locks for office doors. That is the same question slk 9905a door fit notes has to answer here.Once the fit package is complete, request a project quotation and representative samples through the request-a-quote process. Include the controlled drawings, door measurements, configuration, finish and unresolved exceptions. Request samples through order-samples with the same references so the evaluation reflects the door schedule rather than a generic display unit. The commercial offer should identify the configuration and evidence package to which it applies, giving procurement a traceable basis for release.

Twój koszyk
Twoje doświadczenie na tej stronie zostanie poprawione dzięki zezwoleniu na pliki cookie Polityka plików cookie
Chat on WhatsApp