Replacing Doors or Locks with SLK-9905A: A Fit Checklist
Procurement managers use the slk 9905a door fit notes to separate an apparent lock replacement from a verified fit. The decision may involve retaining the door leaf, replacing the lock, or replacing both. Visual similarity is not enough: the door thickness, lock case, cylinder interface, spindle, strike, retained hardware and access-management requirements must all be reconciled.
Direct answer. In brief, this article covers slk 9905a door fit notes from slk 9905a door fit notes to slk-9905a. It states what to confirm about slk 9905a door fit notes on the dated product page where a figure is involved. A slk 9905a door fit notes is a component-level look at how the technology behaves. slk 9905a door fit notes is where the limits sit. slk 9905a door fit notes is verified on the dated product page.
Read slk 9905a door fit notes as slk 9905a door fit notes. It is a working definition of slk 9905a door fit notes. Not a statutory or certified one. It applies to the market and product in question rather than as a general claim.
The published SLK-9905A record identifies it as an RFID hotel lock with a hidden card reader. It lists hotel wooden and metal doors, a 38–100 mm door-thickness range and a 7-pin high-security profile cylinder. It does not provide a complete dimensional drawing in the supplied catalogue entry, so those figures do not establish that every hotel lock of similar appearance can be exchanged. Confirm on the dated product page for the specific SKU and obtain the applicable dimension drawings before releasing a project order.
Clause 1 — Define which part of the opening is being replaced
A fit review becomes clearer when the buyer names the replacement boundary before comparing products. “Replace the lock” can mean exchanging only the visible panel while leaving the lock case, cylinder, spindle and strike in place. It can also mean installing a new lock case and related hardware in the existing leaf. A full door replacement changes the frame, rebate, handle, seal and site-access work as well as the lock.
Use this clause to assign one scope code to every door in the schedule:
| Scope code | Parts retained | Parts replaced | Required starting evidence |
|---|---|---|---|
| A | Door leaf and principal hardware | Lock assembly and affected interfaces | Existing door measurements and photographs |
| B | Door leaf and lock case | Panel, cylinder and affected interfaces | Lock-case and cylinder drawings |
| C | Principal site works | Door leaf, lock assembly and affected hardware | New-door drawings and site opening schedule |
| D | Undecided | Undecided | Evidence-gathering inspection required |
Do not assign scope from the model number alone. A door marked for scope A can become scope B if the existing mortise case does not match the dated SLK-9905A drawing. A door marked for scope C can return to scope A if the replacement leaf arrives with compatible interfaces and the project accepts that finish.
Clause 2 — Freeze the catalogue baseline before the site inspection
The baseline gives inspectors the same starting facts for every door. The supplied catalogue record lists the SLK-9905A as an RFID/IC card hotel lock using Mifare-1 13.56 MHz cards. Its platform is hotel lock management software with a PC encoder and guest cards. The recorded network arrangement is a standalone lock with a PC-linked card encoder, and no in-room network is required.
| Baseline item | Published SLK-9905A record | Use in the fit decision |
|---|---|---|
| Door thickness | 38–100 mm | Compare with measured leaf thickness; do not infer from door width |
| Door type | Hotel wooden / metal doors | Confirm the actual leaf and frame construction |
| Cylinder | 7-pin high-security profile cylinder | Check the existing cylinder interface, not only the keyway appearance |
| Access | RFID/IC card: Standard | Confirm the card platform required at the property |
| Management arrangement | PC encoder, guest cards and standalone lock operation | Check whether existing access administration must continue |
| Power | Four AA alkaline batteries with low-battery alert | Confirm battery access and maintenance ownership |
| Finish | Satin nickel or powder black | Record the selected finish and obtain a physical reference where needed |
| Documentation | Drawings, installation guide and datasheet available on request | Obtain the exact revision used for approval |
For the wider specification record, read SLK-9905A: Reading the Published Specification Without Guesswork. It complements this handbook by showing which catalogue fields are useful facts and which missing fields must still be sourced.
Clause 3 — Choose the replacement route with a recorded gate
The replacement route should follow a simple sequence. First establish whether the leaf will be retained. Then measure the door and its interfaces. Compare those measurements with the dated drawings. Only after that comparison should a sample move into an installation test.
flowchart TD
A[Lock the replacement scope] --> B{Retain the existing door leaf?}
B -- Yes --> C[Measure leaf frame and retained hardware]
B -- No --> D[Obtain new leaf and frame details]
C --> E{Dated drawing matches site evidence?}
D --> E
E -- Yes --> F[Move to sample fit check]
E -- No --> G[Open and assign a fit exception]
G --> F
This gate produces three outputs rather than an informal yes or no:
- Accepted route: the selected scope agrees with the dated drawing, the site record and the physical sample.
- Conditional route: the fit can proceed only after a named exception receives written evidence and approval.
- Rejected route: the proposed interface cannot be reconciled without changing the door, lock case or retained hardware.
For a hotel lock retrofit, retain the completed site record rather than a cropped lock photograph. A photograph may conceal the frame rebate, keeper position, door thickness or the path required for the concealed reader. The Smart Lock Retrofit Site Survey process is useful for establishing the survey scope, while this checklist adds the SLK-9905A-specific interfaces that must appear in the final evidence package.
Clause 4 — Measure the hotel wooden door or metal door leaf
The recorded 38–100 mm range is a screening boundary, not a complete installation drawing. Record the actual thickness at several points and explain any variation rather than selecting the largest reading. Also identify whether the leaf is wooden or metal because the catalogue names both as suitable door types, but that does not remove the need to inspect construction, reinforcement and fixing conditions.
A site measurement record should contain the following fields:
| Measurement | How to record it | Acceptance basis |
|---|---|---|
| Leaf thickness | Record actual readings at hinge, middle and latch positions | Must fall within the range shown on the dated SKU drawing |
| Leaf width and height | Record overall dimensions and any unusual shaping | Used to check handle, reader and frame clearance |
| Material and build | Identify the hotel wooden door or metal door construction | Supplier confirms suitability from the site description |
| Frame rebate | Record depth, width and any uneven section | Compare with the lock case and strike drawing |
| Backset | Measure from the door edge to the lock-case reference point | Do not adopt a value inferred from a visual template |
| Fixing positions | Mark and photograph existing lock and strike fixing points | Compare centres and tolerances with the drawing |
| Door swing and handing | Record hinge side, opening direction and handing | Confirm the correct lock orientation |
| Reader route | Note available face, reveal and routing space | Confirm the hidden-reader position before fabrication |
Do not approve a leaf merely because its nominal size appears familiar. An unusual rebate, shallow lock edge, reinforced metal face or irregular frame can change the required work.
Clause 5 — Reconcile the mortise case and cylinder interface
The catalogue identifies a 7-pin high-security profile cylinder for the SLK-9905A. An existing cylinder with a similar visible profile can still differ in its case interface, cam arrangement, fixing method or relationship to the mortise case. The buyer therefore needs more than a photograph of the keyway.
Request the following evidence for each retained or replacement lock case:
| Interface | Evidence required | Action when evidence conflicts |
|---|---|---|
| Mortise case | Dimensioned drawing and physical measurement | Change the lock-case scope |
| Cylinder profile | Cylinder drawing and existing case measurement | Retain the case only if the interface is confirmed |
| Spindle | Spindle position, section and engagement details | Select an approved alternative or revise the door |
| Cylinder fixing | Fixing centres and attachment method | Reconsider the retained case or cylinder |
| Lock-case edge distance | Measured distance from door edge to case | Compare with the dated drawing |
| Strike position | Frame keeper location and fixing centres | Adjust scope or frame work |
| Bolt or latch travel | Existing case movement and projection | Verify operation with the selected door |
Clause 6 — Test the hardware system around the lock
The lock operates within a hardware assembly rather than in isolation. Latch or deadbolt travel can be affected by the strike plate and keeper. Lever or handle clearance can depend on the escutcheon position. A door closer or hold-open device can alter the force through the latch, while an escape device imposes a separate operating requirement.
Ask the site team to mark each retained item on the door record:
| Component | Fit question | Required evidence |
|---|---|---|
| Latch or deadbolt | Does the selected mechanism meet the existing door edge and keeper arrangement? | Case drawing, edge measurement and operating test |
| Strike plate | Are the opening, fixing centres and keeper position compatible? | Marked strike photograph and dimensions |
| Strike keeper | Is the frame material and reinforcement adequate for the proposed fixing? | Frame inspection record |
| Lever or handle | Is there sufficient internal clearance and correct spindle engagement? | Handle measurement and sample operation |
| Door closer | Can the door close normally with the lock installed? | Closer adjustment record and test result |
| Hold-open device | Does the latch remain compatible with the selected hold-open arrangement? | Written arrangement and operating test |
| Escape device | Does the lock and handle arrangement preserve the intended escape movement? | Site-team verification and test record |
| Concealed reader | Is the chosen position reachable and consistent with the door construction? | Marked reader location and routing plan |
Where the property or project imposes a requirement concerning door operation or escape hardware, request the written requirement and the evidence it requires. Do not infer compliance from the catalogue record.
CONFIRM-WITH-LOCAL-SITE-TEAM: Confirm any project-specific door, escape-hardware or access-control requirement before approving the retained hardware arrangement.
Clause 7 — Check power and credential-management dependencies
Physical fit does not end at the door face. The published SLK-9905A record lists four AA alkaline batteries and a standard low-battery alert. At the door, that means the installation team must have a defined way to access and service the battery compartment without damaging the panel or finish. Record the proposed battery-change route and who will own the maintenance task.
| Dependency | Buyer question | Acceptance evidence |
|---|---|---|
| Card standard | Are the required guest and staff cards based on the recorded Mifare-1 13.56 MHz arrangement? | Card sample and written platform confirmation |
| Encoder | Where will the PC-linked card encoder be installed and connected? | Equipment schedule and tested issuance workflow |
| Guest-card issuance | Who issues, cancels and recovers cards? | Named process and responsible role |
| Permissions | How will floor and room permissions be assigned? | Tested permission example |
| Validity windows | How will check-in validity windows be configured? | Approved workflow and test record |
| Unlock records | Which records must be retained and reviewed? | Confirmed report requirement |
| In-room network | Is the stated no-in-room-network arrangement appropriate for this project? | Signed system-scope decision |
| Batteries | Where will four AA alkaline batteries be accessed and replaced? | Maintenance instruction |
For the wider management decision, use Configuring SLK-9905A: Credential Choices and Management Tools. Keep that software review connected to the door record because a credential decision can change the panel configuration, reader position, encoder requirement and replacement boundary.
The catalogue fields establish a starting scope; they do not replace a project-specific interface test.
Clause 8 — Mark environmental uncertainty instead of assuming
The environment field in the supplied SLK-9905A catalogue entry is an em dash. In other words, the published record used for this handbook does not state an operating temperature range, humidity range or weatherproof-housing specification for this SKU. Those capabilities must not be inferred from the broader catalogue.
That absence matters when a hotel lock is considered for an exterior door, a sheltered entrance, a washdown area or another non-standard location. Record the actual exposure rather than relying on the room label. Include whether rain reaches the face, whether cleaning water collects around the panel, whether the door faces direct sunlight, whether salt or industrial atmosphere is present, and whether the reader position is exposed.
| Site condition | Required question | Disposition if unanswered |
|---|---|---|
| Interior controlled opening | Is normal indoor operation the intended scope? | Record the site condition and supplier confirmation |
| Exterior or sheltered entrance | What exposure does the face and concealed reader encounter? | Keep environmental suitability open |
| Washdown or cleaning exposure | Can water enter the reader, cylinder or battery area? | Obtain specific guidance before approval |
| Direct sunlight | Is there a stated temperature range for the selected configuration? | Do not infer suitability from another model |
| Metal door in a coastal setting | What site-specific exposure applies? | Require written project guidance |
Clause 9 — Account for the packing and project-order boundary
The catalogue gives the SLK-9905A export-carton record as 485 × 330 × 445 mm, with six units per carton and a gross weight of 16.1 kg. These figures help procurement plan receiving space, carton handling and the movement from storage to the floor. They do not prove that a replacement will arrive as one complete unit; the required project configuration still has to be stated in the order.
| Published packing field | Recorded value | Procurement implication |
|---|---|---|
| Carton dimensions | 485 × 330 × 445 mm | Check receiving and storage clearance |
| Units per export carton | 6 pcs/ctn | Use only as a packing reference, not a project-order quantity |
| Gross weight per carton | 16.1 kg | Confirm handling arrangements at the delivery point |
| Configuration | Custom logo, finish, packaging, manuals and product configuration for distributor and project orders | Define the exact configuration in the order file |
| Documentation | Dimension drawings, installation guide and full datasheet available on request | Attach or reference the approved document revisions |
The SLK-9905A Order Checklist for Project and Repeat Purchases provides the order-side sequence. Add the door-specific drawings and exception status from this fit handbook so a repeated purchase is based on an approved configuration rather than a copied model name.
Clause 10 — Assemble one auditable fit-evidence package
| Evidence record | Required contents | Pass condition |
|---|---|---|
| Door schedule | Door identifier, location, scope code and hardware status | One scope assigned to each door |
| Measurement sheet | Thickness, rebate, backset, fixing centres and door construction | Meets the released drawing or has an assigned exception |
| Photo set | Full door, lock edge, frame, strike, handle and retained devices | Images are legible and tied to the door identifier |
| Dated SKU record | Current model record and configuration reference | Matches the item being evaluated |
| Dimension drawing | Door-fit and lock-interface drawing | Correct revision approved by the project team |
| Installation guide | Relevant installation steps for the configuration | Revision recorded in the fit file |
| Datasheet | Published specification and environmental entries | Matches the selected configuration |
| Hardware schedule | Retained and replaced components | No unassigned interface remains |
| Sample-fit record | Installation and operating observations | All mandatory checks accepted |
| Exception log | Open issue, owner, evidence and disposition | No unapproved blocker remains |
Clause 11 — Run the representative sample before the wider
A sample fit check should use a representative door rather than the most convenient opening. Select a door that includes the most demanding retained hardware or construction condition identified in the survey. If several door types exist, use separate samples or separate test plans for each type.
Use this sequence for the sample:
- Check the leaf, frame, lock case and strike against the released drawing before applying finish.
- Install the lock case and cylinder while retaining access to the spindle, cylinder fixing and case fixing.
- Confirm the concealed-reader position and the available routing path against the approved door drawing.
- Fit the panel, handle or lever and check free movement without forcing the door.
- Install or retain the closer, hold-open and escape devices in their intended positions.
- Test latch and bolt operation with the door closing under normal conditions.
- Connect the specified encoder and management arrangement, then issue and test the required card types.
- Verify guest-card issuance, the relevant permission, validity-window operation and unlock-record retrieval.
- Record battery-compartment access and the low-battery alert procedure.
- Photograph the completed installation and update the exception log.
Do not use a successful card unlock as proof of a complete fit. Mechanical movement, frame clearance, retained devices, reader routing and record retrieval each need their own evidence. Conversely, a clean visual installation does not establish that the management arrangement works.
Clause 12 — Code exceptions so they cannot disappear
| Code | Trigger | Initial disposition | Evidence required to close |
|---|---|---|---|
| F-01 | Door thickness or construction is unresolved | Conditional | Measurement sheet and supplier confirmation |
| M-01 | Lock case, spindle or cylinder interface conflicts | Conditional or rejected | Dated drawing and approved case comparison |
| B-01 | Backset or fixing centres cannot be reconciled | Conditional | Door measurement and revised fit method |
| H-01 | Retained closer, hold-open or escape device interferes | Conditional | Marked hardware test and site approval |
| S-01 | Strike or keeper arrangement is unsuitable | Conditional | Frame measurement and operating result |
| P-01 | Battery access or power arrangement is unclear | Conditional | Maintenance record and panel-access check |
| R-01 | Reader position or routing is unavailable | Conditional | Approved reader layout and sample result |
| C-01 | Card or management workflow is unresolved | Conditional | Encoder and credential test record |
| E-01 | Environmental exposure is outside the documented evidence | Unresolved | Specific dated guidance for the SKU |
| D-01 | Drawing, guide or datasheet revision is missing | Unresolved | Controlled document set |
| F-02 | Selected finish is unavailable or unconfirmed | Conditional | Finish confirmation and reference sample |
A conditional approval should identify the condition, not merely state “subject to fit.” It should state what evidence closes the issue and who signs the closure. If an exception changes the replacement scope, revise the door schedule and the affected commercial request before proceeding.
Clause 13 — Gate the release of replacement hardware
| Release control | Procurement check | Required sign-off |
|---|---|---|
| Door scope | Every door has scope A, B, C or D | Site team |
| Measurement | Required fields are complete | Installer or site inspector |
| SLK-9905A configuration | SKU, finish and configuration are identified | Procurement and supplier |
| Drawing control | Current drawing, guide and datasheet are referenced | Technical reviewer |
| Hardware | Retained and replaced components are listed | Installer |
| Credential plan | Encoder, cards and records have named owners | Access-management owner |
| Sample | Representative fit test is accepted | Technical reviewer |
| Exceptions | Blockers are closed or formally declined | Authorised project approver |
| Order references | Purchase record points to the approved fit package | Procurement |
| Installation handover | Installer receives the same controlled revision | Site team |
A bulk replacement should not proceed from a successful sample of one door type when another type has a different leaf, strike or retained-hardware arrangement. Group doors by physical configuration, test each group and identify which sample represents it. That method makes the approval traceable without assuming that all hotel wooden doors share one installation condition.
Clause 14 — Write the door information into the request-for-quote
A useful RFQ gives the supplier enough information to return a relevant configuration and identify unresolved interfaces. The Office Smart Lock Site Survey shows how to organise the site-record side of the review; the project-specific fields below add the SLK-9905A replacement decision.
| RFQ field | Information to include |
|---|---|
| Intended configuration | SLK-9905A, selected finish and project scope |
| Door population | Door identifiers, quantities and physical types |
| Leaf measurement | Actual thickness, rebate, backset and fixing positions |
| Door construction | Hotel wooden door or metal door description |
| Existing lock | Case, cylinder, spindle, handle, latch and strike arrangement |
| Retained hardware | Closer, hold-open and escape-device details |
| Reader arrangement | Required concealed-reader location and routing information |
| Management requirement | Encoder, card, permission and unlock-record needs |
| Environment | Exposure at each representative door location |
| Document request | Dimension drawings, installation guide and full datasheet |
| Sample request | Representative-door fit test and documentation |
| Commercial reference | The approved fit-package reference |
Clause 15 — Preserve a handover record at the installed door
The handover should preserve the decisions that made the installation workable. Store the approved drawing, measurement sheet, exception closure and relevant installation reference with the building’s maintenance record. Identify the lock configuration and selected finish in the asset register so a later replacement does not start from the original uncertainty.
Use the handover sequence below:
| Stage | Record to complete |
|---|---|
| Before installation | Verify the door identifier, document revision, configuration and retained hardware |
| During installation | Record removed parts, installed parts, adjustments and reader routing |
| At commissioning | Record card test, permission test, unlock-record test and mechanical operation |
| After adjustment | Record closer interaction, handle movement and any modified hardware arrangement |
| At acceptance | Attach the approved fit package and close the exception log |
| For future maintenance | Link the asset record to the configuration, finish and controlled documents |
A future installer should be able to understand why a particular lock case, strike, reader position or door preparation was accepted. That history is particularly valuable when the project later changes from lock replacement to full door replacement, or when a repeated purchase uses the SLK-9905A across several properties.
The same question is worked through in more detail in narrow edge locks for office doors. That is the same question slk 9905a door fit notes has to answer here.Once the fit package is complete, request a project quotation and representative samples through the request-a-quote process. Include the controlled drawings, door measurements, configuration, finish and unresolved exceptions. Request samples through order-samples with the same references so the evaluation reflects the door schedule rather than a generic display unit. The commercial offer should identify the configuration and evidence package to which it applies, giving procurement a traceable basis for release.

