A campsites door survey records every pod, lodge, gate and washroom door, then decides what fits, what moves each season and what the site can service alone.

Geplaatst op: mei 06, 2026

Smart Locks for Campsites, Glamping and Park Lodges: Door Survey and Fit Reality

Smart Locks for Campsites, Glamping and Park Lodges: Door Survey and Fit Reality

A campsite is the rare place where the door list is true for one season only. Pods arrive on a flatbed in March and go back on one in November. A lodge that had three bedrooms last year has five this year. The gate that took the delivery van in the spring takes a camper with a tow bar in the summer, and a different entrance takes the vehicles in winter because the main one floods. Any survey that records a count — twenty-four units, sixty doors — is out of date before the quotation is written. A campsites door survey is therefore not a measurement sheet with a site address on it. It is a per-leaf record built to be re-pointed at a different population next spring, carrying enough evidence on each leaf that a supplier can price the work without walking the site again.

  • Split the door types — sort the door population into classes that behave alike, starting from campsites door survey
  • Match each type to a class — state what five door populations needs before anything is quoted
  • Evidence the fit — record the measurement that closes campsites door survey
  • Treat this as the campsites door survey sequence, with campsites as the reference.

The physical side of that population is unlike a hotel. These are outdoor and semi-outdoor doors in rain, sun and salt: a pod door, a lodge or cabin entry, a site gate, a washroom block, a waterside or equipment store. Power is frequently off-grid or solar, so a reader on a washroom block may have no mains socket anywhere near it. The labour is seasonal too. The person who re-issues the credentials in May is not the person who re-issues them in September, and neither of them is a locksmith.

Direct answer. A campsites door survey is a re-pointable per-door decision record. For every leaf it settles three questions: whether a lock can physically live on that door, whether the site can maintain it without a specialist, and whether the credential it carries can be voided at the season boundary by the people on site. It runs in six stages — frame the closing question, classify the door population, walk and measure every leaf, test the credential behaviour, establish the power and egress posture, and issue a door schedule keyed to a location rather than to a unit number.

This guide is written for the property manager who has to return a survey to a supplier or to an owner. It covers a single-site campsite, a multi-site park operation and the glamping park where pods are leased to individual operators. Where the site is already fitted, the published Smart Lock Retrofit Site Survey covers the retrofit framing; where the accommodation is a building rather than a pod, the Hotel Smart Lock Site Survey covers the measurement discipline a lodge borrows from a hotel.

The five door populations, and why they cannot share one

The campsite door population splits into five groups, and the split matters more than the count. A pod door, a lodge entry, a site gate, a washroom block and an equipment store look superficially like five versions of the same door on a plan. In the hand they are five different products with five different failure stories, and the survey has to treat them separately from the first hour.

The pod door is the odd one out. A glamping pod is often a moulded shell or a framed timber box delivered complete, and the door in it is a small leaf in a narrow frame with very little flat surface on either face. A glamping pod door lock is therefore judged on the stile before it is judged on anything else: the reader has to sit somewhere, and a panel that is too tall for the stile is not a cheaper option — it is a door that cannot be fitted. The whole pod may also leave the site in autumn, which means the lock leaves with it, or the pod stays and the lock stays and the site has one fewer working door over winter. Specifications at this level come off the smart door locks.

The lodge or cabin entry is the opposite problem: a real door in a real building, often a proper mortise pocket, sometimes already carrying a multipoint locking system on a newer build. Park lodge door hardware is the one part of a campsite estate that a landlord or a tenant may actually own rather than the site operator, which is why a survey sometimes has two readers of the same schedule. Fitting a mortise smart lock to a door that already has a multipoint gear requires a spindle converter, and whether the converter is supplied is a per-model question the survey has to ask rather than assume.

The site gate, the washroom block and the equipment store are all outdoor or semi-outdoor, and each has its own dominant damage. The gate takes vehicles and wind. The washroom block takes hose water, splashback and several hundred openings a day. The equipment store takes salt and damp and holds things worth taking.

Door populationDominant environmentThe hard fit questionWhat a wrong answer looks like
Pod doorRain on a narrow stile, whole unit may be relocatedIs there a flat mounting face wide enough for the reader panelA pod delivered with no lock at all
Lodge or cabin entrySheltered, but heavy timber and possible multipoint lockingCan the mortise case and spindle reach the existing mechanismA door that closes but will not latch under its closer
Site gateRain, sun, salt, vehicles, wind on the leafDoes the lock mount on the rail or the post, and what stands the spindle off the faceA gate that fails in the first wet season with no local repair
Washroom blockSplashback, hose wash, near-constant trafficDoes the hardware survive cleaning and still latch when swollenA locked door that cannot be opened in an emergency
Equipment storeDamp, salt, unsecured storage of high-value gearIs the frame reinforced enough to carry a strikeA door that secures nothing because the frame gives way

A survey that survives the season is keyed to the place

Most campsite survey templates fail on a simple clerical point. The door reference is written as a unit number, and unit numbers are the one thing a campsite changes every year. Pod 14 was at the top of the site last season and is beside the lake this season, and the reference still says 14.

So the reference has to be a location, not an occupancy. A location reference in a campsite survey has three parts: a permanent marker the eye can find without a site map, the position of the door on the structure, and the role the door plays. That sounds fussy until the first season rolls over and the person re-issuing credentials cannot tell which physical door is door 14 any more.

What the schedule recordsWhy it has to be written this way
A permanent location referenceUnit numbers are re-used and re-assigned every season
The structural position, such as the gate leaf or the lodge side porchTwo doors on the same unit behave differently in weather
The role, such as guest entry, service, store or perimeterThe role decides the credential, not the unit number
Whether the door moves with a relocatable unitA lock that leaves with the pod is not a site asset
The season the record was last confirmedA stale leaf is worse than a missing leaf

That last row is worth defending, because it sounds like bureaucracy until a surveyor finds a pod leaf that was measured two seasons ago and has since been replaced with a lighter one. A campsite survey is not a survey of the site; it is a survey of the site as it stands in a named season, with a date on it and a list of what has changed since.

The seasonal credential reset has a survey dimension too, and it is the dimension the vertical's own first question points at: what happens to the credentials and the batteries when the site closes for the winter? The survey does not answer that, and it must not try to. What it does is record, per door, whether the credential on that door is expected to expire at the season boundary or to be wiped when the last guest leaves, and whether the batteries are expected to be removed, left in place, or swapped at closing. Those two answers per leaf are what tell the supplier whether the product needs an offline wipe path and how many spares the warden must hold. A campsite door survey carrying those two answers is also the document a returning warden can act on without a call to anybody. The credential design itself is a separate piece of work: Smart Lock Key Control and Master Key Decisions for Campsites, Glamping and Park Lodges covers the hierarchy, and Smart Locks for Campsites, Glamping and Park Lodges: Credential Model that Survives Annual Re-Issue at Season Start works through the re-issue model itself.

Stage one: the question that has to be answered before anyone

The failure point at most campsites is the brief rather than the site itself. A walk round carried out without an agreed method produces notes that cannot be priced later, because nobody settled what a measured field was supposed to mean before the first tape came out of the case. The sequence below is the one that holds up when a supplier asks where each figure came from.

flowchart TD
    A[Brief the season boundary first] --> B[Classify the door population]
    B --> C[Walk and measure every leaf]
    C --> D[Test the credential behaviour]
    D --> E[Establish power and egress posture]
    E --> F[Issue the location-keyed schedule]
    C --> G[Leaf outside the candidate range]
    G --> B
    D --> H[Credential cannot be cleared locally]
    H --> E
    E --> I[Answer still missing from an authority]
    I --> F

Stage one is a conversation, and on a campsite it is a conversation about closure. Before anyone visits, the operator answers three things in principle: which doors are closed and locked when the site is shut, which leaves stay in service through the winter, and who is on site to touch a credential or a battery if something has to be done in February. That last answer is the one that changes the specification more than any other, because a site with no winter presence needs products that tolerate a long unpowered period and credentials that expire on their own rather than credentials somebody has to revoke.

Stage two is the classification, done on paper from the site plan and then corrected on site, because the site plan rarely shows the equipment store and never shows the second gate. Stage three is the measurement walk. Stage four is the credential test, where the surveyor watches how the door is actually used rather than how it is described, including the case where the person carrying the load uses a shoulder instead of a handle. Stage five is the power and egress posture, which usually needs a phone call rather than a tape measure. Stage six produces the schedule.

What to carry: the working kit for a campsite walk-round

A campsite survey is unusual in that the walk crosses a site rather than a building, so the kit is half measuring equipment and half site equipment. The list below is a working checklist rather than a specification, and it exists because the failures are mundane: a door photographed from the wrong angle, a leaf measured over the architrave, a gate that was opened for the photographer and therefore never measured in its closed position.

mindmap
  root((Survey kit))
    Measuring
      Tape measure
      Depth gauge
      Feeler gauge
      Thickness callipers
      Spacer block for gate standoffs
    Imaging
      Wide shot of the whole leaf
      Close shot of the strike and keeper
      Shot of the closed gate and the open gate
    Power
      Spare cells in the door type used
      Cable for the emergency power port
      Torch for the inside of a store at midday
    Site
      Printed site plan with the gate marked
      Pencil and tape for marking the leaf
      Sibling and a second pair of hands

The photography rule for a campsite is specific and worth stating: photograph every leaf closed, and photograph the gate twice, once closed and once open. A gate is nearly impossible to measure in the state that matters, because opening it changes the geometry of everything attached to it.

The per-leaf record and the fields a campsite adds to it

The per-leaf sheet is deliberately narrow. Nine or ten fields taken from the door itself decide fit; everything else belongs in a separate schedule because it changes less often. The published Smart Lock Door Measurement Guide sets out the method, and each dimension is handled separately in Smart Lock Door Thickness Measurement, Smart Lock Backset Measurement, Smart Lock Lock Case Measurement and Smart Lock Door Gap Measurement, with the keeper side covered in Smart Lock Strike Plate Measurement.

Field to write downWhat the surveyor recordsWhy it decides somethingWhat voids the record
Leaf thicknessMillimetres, taken at three heights and clear of the edgesSets the lock family, the body length and the spindleA single reading taken near a hinge
Leaf material and finishTimber, composite shell, powder-coated steel, aluminium, glazedDecides the surface the panel and the fingerprint sensor live onAssumed from the building type
Frame and rebateRebate depth, jamb material, frame wall thicknessDecides whether the case sits without routing and whether the leaf closesTaken from a drawing rather than from the leaf
Existing lockPresent, absent, mortise profile, cylinder, or multipoint mechanismDecides whether the door is a retrofit or a replacementAssumed because the key is missing
Backset and spindle positionDistance from the door edge to the cylinder, and the spindle reachDecides whether a standard body reaches the mechanismMeasured to the wrong edge of the leaf
Strike and keeperType, condition, and whether the frame is reinforcedA weak frame is a hole regardless of the reader above itEyeballed with the leaf open
Mounting faceThe flat usable zone on the leaf, stile or frame, and its widthDecides whether the panel can be mounted at all on a pod or a gate railIgnored until a product is offered
ExposureRain reach, sun side, splashback, salt proximity, sheltered or fully exposedDecides the housing class and where the survey has to test rather than assumeAssumed from the site plan
Power availableMains, solar, none, and the distance to the nearest socketDecides whether a reader can be networked at allRecorded as "has power"
Closing behaviourSelf-closing, free swing, held open, wind-drivenDecides the latch behaviour and whether a hold-open device is neededNot watched through a gust of wind

The last three rows are the campsite addition. A hotel survey may treat exposure as a note; here it decides the product class, because the same door leaf in a sheltered porch and on an exposed gate is a different hardware decision.

Fit reality: the thresholds that decide whether a lock

Five thresholds resolve most of the campsite fit questions, and each one fails at installation rather than on paper.

The first is leaf thickness against the model's stated range. This is a per-model figure and the manufacturer records it inconsistently — some rows carry a range, some leave the door fit group empty. A card hotel lock in this manufacturer's catalogue records a door thickness of 36 to 100 mm for wooden and metal doors with a five-pin profile cylinder and a three-point latch. A five-in-one fingerprint mortise lock records a door thickness of 38 to 100 mm with a faceplate of 227 by 66 by 20 mm and an operating range of minus 25 to 65 degrees and 20 to 95 per cent relative humidity. A weatherproof narrow-profile model in the same catalogue records no door thickness at all, and instead gives a mortise lock case of 35 by 85 mm or 40 by 85 mm. That absence is not a range; it is a gap in the record, and the survey should treat it as one. Confirm on the dated product page for the specific SKU before any of these figures is used to accept or reject a leaf.

The second threshold is the rebate and the body. A thicker leaf needs a longer body, and a case deeper than the rebate will not close. The third is the spindle and the standoff, which decides the gate and the pod. The fourth is the strike, where a hollow-core leaf or a thin aluminium frame needs reinforcement that is a joinery job, not a lock decision. The fifth is exposure, where the housing class has to be established from the manufacturer's documentation rather than from a photograph of a product on a bench.

graph LR
    P[Pod or lodge leaf] --> T[Thickness and rebate check]
    T -->|Passes| B[Body and spindle check]
    T -->|Fails| X[Different route or a new leaf]
    B --> S[Strike and keeper check]
    S -->|Passes| F[Fit verdict recorded on the schedule]
    S -->|Fails| Y[Frame work before any fitting]
    G[Site gate] --> V[Mounting face and standoff check]
    V --> F
    F --> Q[Quotation can be priced from the sheet]

The survey's output at this point is a verdict per leaf, and there are only four verdicts worth writing down: it fits as recorded, it fits subject to a stated condition, it does not fit and needs a different route, or it has not been established because the power or the leaf could not be examined. That last verdict is the honest one, and it is better than a guess: a leaf behind a stacked container is a leaf whose thickness nobody has measured.

The site gate is a different object from a door

The site gate deserves its own treatment because it is where the vertical's stated failure mode lives — a product chosen for the guest-room fit and then asked to work on a site gate in the wet season with no local maintenance. Three things make a gate different.

The first is geometry, and a site gate access survey starts with the gate type rather than with the lock. A gate leaf is a frame, not a slab. A lock body either mounts on the horizontal rail, where the stile width is narrow and the spindle stands off the door face by a distance that varies with the gate's own sag, or it mounts on the post, where the leaf has to be drilled for a keep and the post has to be heavy enough to take the load. Both routes are legitimate and both need a standoff figure that a standard door measurement does not produce. One catalogue row in the keypad family records a zinc deadbolt described as adjustable between 60 and 70 mm, which is a reminder that adjustability is a per-model field rather than a general property of the category.

The second is the load and the weather. A gate leaf moves in wind, and a lock whose latch is not a positive deadbolt may not hold the leaf against a gust that tries to swing it. A gate that is driven by a vehicle needs a surface-mounted or concealed closer with the correct rating, and the survey records whether the closer exists, what type it is, and whether it has been adjusted since installation — a gate closer that has been disconnected in a previous season is the most common finding on an outdoor gate at any site.

The third is power. A gate at the far end of a site is often the one place with no mains and no signal, and a gate is exactly where a remote release is most valuable to a warden driving a mower. The survey records whether the gate is on the perimeter of the network, whether solar is available and who maintains the panel, and whether the manual override survives a flat battery. The outdoor gate product route on the manufacturer's site is at smart lock for outdoor gates, and the environmental framing is set out in Smart Lock Outdoor Security Considerations.

Washroom blocks, pod doors and the hardware that lives in the rain

A washroom block is a semi-outdoor building in most campsites: two or three cubicles, a basin, a door that has to close at night in a place where nobody is watching it. Its door is usually the one leaf on the site that sees the most openings per day, and the one that gets the most abuse from a hose and from wet hands.

Three survey findings matter here. The first is the strike and the swollen leaf. A block door in a wet climate swells in the wet season and shrinks in the dry one, and a lock fitted to a door in August can bind in January. The survey should record the door gap and the gap under the door leaf, and it should record which way the door was hung, because a door hung to swing against the prevailing weather direction moves differently.

The second finding is the panel's position. A washroom reader sits at hand height on the outside of a door that people approach with wet hands and a full bag. That is a case for a code and a card rather than for a fingerprint pad, and it is a case the catalogue supports: several weatherproof aluminium models in this manufacturer's range record RFID or card, passcode, fingerprint, a mobile app and a mechanical override as standard access methods, with a weatherproof housing recorded in their environment field and a low-battery alert recorded on their power supply.

The third finding is the a campsite washroom block lock cannot resolve on its own: the egress arrangement. A block door that has to be opened from the outside in an emergency is not a hardware decision, and a reader fitted to a door that has to fail open on a signal is a decision for the fire authority rather than for a supplier. The same applies to a self check-in point, where a keypad carries the code for a guest arriving after dark into a site nobody is watching.

CONFIRM-WITH-LOCAL-FIRE-AUTHORITY — Ask the fire authority, or the site's own fire risk assessment author, which doors at a campsite are used for escape and what locking arrangement each one may carry, including the washroom block, the lodge entrance and any gate that forms part of a pedestrian route. Confirm locally what the manual release must do when the door is unpowered, and keep the written answer with the door schedule rather than in an email.

Off-grid power and the exposure-versus-consequence map

The two questions a campsite survey has to answer about hardware are not the same question, and the survey records them separately. The first is environmental: how hard is this door worked? The second is consequential: what is behind it? A door that is fully exposed but protects nothing valuable needs a modest hardware decision and a tolerant replacement plan. A sheltered door in front of valuable equipment needs a better hardware decision, but it will not be tested by weather.

Plotted against each other, the campsite's doors fall into four groups, and the quadrant decides what the survey has to prove before a model can be named.

quadrantChart
    title Door classes by weather exposure and security consequence
    x-axis Sheltered --> Fully exposed
    y-axis Low consequence --> High consequence
    quadrant-1 Exposed and valuable
    quadrant-2 Sheltered and valuable
    quadrant-3 Sheltered and low value
    quadrant-4 Exposed and low value
    "Lodge or cabin entry": [0.2, 0.8]
    "Pod door": [0.55, 0.45]
    "Site vehicle gate": [0.9, 0.55]
    "Washroom block": [0.8, 0.25]
    "Equipment store": [0.65, 0.7]
    "Self check-in point": [0.3, 0.5]

The top-right quadrant is the expensive one. An exposed store holding generators, outboards and fuel is a door that needs a housing class the manufacturer will stand behind, a strike on a reinforced frame, and a replacement plan the site can execute. The bottom-right quadrant is the false economy: a washroom block is fully exposed, but the consequence of a failure is a locked door in the rain rather than a loss, so the correct decision there is often a simpler lock, a better maintained one, and a manual route that has been walked rather than documented.

The power question belongs in the same section because on a campsite they are entangled. Off-grid site power means the reader runs on cells, the gateway cannot rely on a wired network, and the solar panel that charges the battery is itself a piece of equipment that somebody has to keep clear of leaves. The survey records, per leaf, what power exists, who maintains it and when it was last checked. The programme behind that record — cell choice, rotation, the winter read — is a separate piece of work and Battery and Power Programme for Smart Locks in Campsites, Glamping and Park Lodges covers it in full.

Choosing a lock family from what the survey

The catalogue for this manufacturer is wide — smart door locks, fingerprint locks, keypad locks, hotel card locks, glass door locks, cabinet locks and an outdoor aluminium series — so the survey's real work is narrowing it. The narrowing below starts from the door, not from the model.

Door classAccess route that fitsModel family to evaluateThe catalogue field that decides itConfirm before naming a model
Lodge and cabin entryCard or code with a season-scoped credentialHotel card lock with a card encoderStated door thickness range and mortise profileThickness range and panel size on the dated page
Pod doorCode and card, with the whole unit possibly relocatingWeatherproof narrow-profile lockLock case size and the panel footprintWhether the mounting face fits the stile
Site vehicle gateCode with a mechanical override and a manual releaseWeatherproof aluminium gate lockHousing class and power supplyEnclosure coverage and battery life on the dated page
Washroom blockCode, with a card as the warden's routeOutdoor keypad lock with a low-battery alertHousing class and low-battery alertEnclosure coverage and the override arrangement
Equipment store and internal cabinetsCard, with the store door and the cabinet on one credentialCabinet lock body for the inner casesAccess fields listed for that modelWhether the cabinet accepts the same card as the door
Glazed lodge door or reception screenLocal reader on the glass fittingGlass door lockGlass thickness range and patch fitting typeWhether the patch fitting suits the glazing

A card hotel lock in the hotel family records card access and a mechanical override, a stainless steel and alloy body with a five-pin high-security profile cylinder and a three-point latch, a door thickness range of 36 to 100 mm, a supply of four AA cells, and a standalone arrangement driven by a PC-linked card encoder that the catalogue records as needing no in-room network. A weatherproof single-sided model for courtyard aluminium gates records an aluminium alloy body, four AA alkaline cells, a low-battery alert, a weatherproof housing, and a platform offering remote unlock, temporary and periodic passcodes, user management and access records. A stainless steel dual-sided keypad model in the keypad family records card, passcode, a mobile app and a mechanical override with Bluetooth connectivity, and leaves both its power group and its door fit group empty — an absence that means the fit has to come from the manufacturer's documentation rather than from the range sheet.

The point of the last paragraph is the argument of this whole article. The two figures that decide whether a campsite door can be modified at all are the thickness range and the enclosure class, and they are recorded per model and per door rather than per building. The pod door decision is usually settled by the mounting face, and the gate decision by the standoff. A survey that has not captured those two things per leaf has not captured anything a supplier can price.

What a campsite survey cannot answer on its own

No survey closes every question, and a document that claims it has should be read carefully before it is signed rather than after the hardware is ordered. Each of these belongs to somebody else, and the survey's job is to record who that somebody is and whether the answer has been obtained.

Question the buyer is askedWho actually answers itWhat the survey records
Which leaves may be locked without a key on the insideThe fire authority or the site's fire risk assessment authorThe locking arrangement per door, and the date the answer was given
Is the gate on a pedestrian escape routeThe fire authorityWhether an answer exists, and who gave it
May a reader be interfaced with anything on siteThe site's own system ownerWhether the door is interfaced today
What may be recorded about guest movements through a siteThe data-protection reviewerThe logging position per door class and the date it was agreed
How long a guest credential stays validThe operator, on adviceThe credential validity window per door class
Whether a reader survives a full winter outdoorsA site trial on a real doorThe trial result, or an explicit note that it was not proven
What the site power can actually deliverThe site's electrical contractor or its energy supplierThe power source per leaf and the maintenance owner

Two of these are worth pulling out, because on a campsite they change the specification rather than merely annotate it. The first is the guest movement record. A site that logs every entry across a pod and a gate is holding a record about named guests and where they went on the site, which is a decision for the operator and whoever advises it on data obligations rather than a default setting in a lock. The Data Retention and Privacy for Smart Locks in Campsites, Glamping and Park Lodges piece covers the retention side, and Audit Trail Requirements for Smart Locks in Campsites, Glamping and Park Lodges: What Records Matter covers which records are worth keeping at all.

The second is the winter trial. No datasheet tells a property manager how a lock behaves on their own gate after a season of salt and rain, and the survey should therefore end with one question that cannot be answered by measurement: which leaf on this site is the worst case, and will a candidate model be trialled on it before the season opens.

CONFIRM-WITH-LOCAL-DATA-PROTECTION-REVIEW — Ask the data-protection reviewer, or the operator's own adviser, what the site may record about guest movements and credentials, who may read those records, how long they are kept and where they are held. Get the position per door class before any reader that produces records is specified, and take the answer from the reviewing authority rather than from the equipment supplier.

Turning the survey sheet into something a supplier can quote

A completed survey is only useful if it converts into a document a supplier can quote against, and on a campsite that document has to do two jobs: price this season, and survive next season. The schedule carries, per leaf, a location reference, the door class, the measured fit fields, the exposure and power position, the access route, the credential position, the fit verdict, the catalogue figures used with their confirmation status, and the open questions with an owner.

Item in the supplier packWhy a campsite needs it specificallyWhere it is checked
Dimension drawing per candidate modelResolves thickness, body length and panel footprint against the leafAgainst each leaf's measured fields
Stated door thickness rangeThe first filter; a leaf outside it needs a different routeAgainst the thickness column
Lock case, mortise and panel dimensionsDecides the rebate conflict and the mounting faceAgainst the rebate and mounting face fields
Spindle and standoff optionsThe deciding measurement on a gate or a podAgainst the standoff field
Strike and keeper options, including reinforcementA thin frame needs work regardless of the lock above itAgainst the strike condition field
Enclosure coverage, stated for the modelDecides whether an exposed door is eligible at allAgainst the exposure column
Power supply and low-battery behaviourDecides the winter read and the spares the warden holdsAgainst the power column
Mechanical override arrangementThe manual route when the cell is flat or the credential failsAgainst the out-of-hours procedure
Configuration options, stated per model versionThe same model name exists in several configurationsOn the quotation, in writing
Documentation available on requestThe submittal needs drawings, guides and datasheetsBefore the order, not after

Buyers who have never walked through a factory ask better questions when they have seen what a check looks like, so two published pieces are worth reading before the first technical call: the Smart Lock Factory Audit Checklist for International Buyers, which covers what to look for on the floor, and How to Verify a Smart Lock Manufacturer Before Placing an Order, which covers what to demand in writing afterwards. The commercial shape of the enquiry sits in the Smart Lock RFQ Guide for International Buyers, and the campsite version, with the door classes already filled in, is the RFQ Template for Smart Locks for Campsites, Glamping and Park Lodges. The compatibility work behind the fit columns is set out separately in Door Types in Campsites, Glamping and Park Lodges: Pod, Lodge and Gate Access Compatibility Notes.

Questions a property manager asks before signing a campsite survey

Does a campsite really need its own survey, or will the hotel template do? The measurement work is the same and the published Hotel Smart Lock Site Survey is a fair starting point. What differs is the population, the exposure and the fact that the doors move. A hotel list is stable for a decade; a campsite list is stable for a season.

How many doors do we need to survey? Every leaf in the pod, lodge, gate, washroom and store classes, because those classes vary far more within themselves than the classes vary from each other. If the site is large and the pods are identical, a representative sample per pod type is defensible — but only if the survey records which pod the sample came from and states that the rest are assumed identical.

What if the fit test fails on a leaf? That is a legitimate survey outcome and one of the reasons to survey before ordering. The schedule records the failure, the reason and the alternative route, and the alternative is often a mechanical solution — a surface-mounted pull bolt, a gate pin, a hasp on a store door — rather than an electronic lock at all.

Can we leave the gate and the washroom block out of it? You can, and it is a decision with a known cost. Both are the doors that take the abuse, and both are the doors where a failure is found by a guest rather than by the site. If they are excluded, the exclusion belongs on the schedule with a name against it.

What happens to the survey when the site closes for the winter? It is filed with the date, the season it describes and the list of what changed. A survey that is not dated is a survey nobody can trust, and a survey that is not compared against the previous season's leaves is how a pod arrives with a door nobody has measured.

Should the survey cover the wifi and the network? Only to the extent of recording whether there is any signal at each door and whether the reader depends on it. The architecture decision follows the survey rather than preceding it, and Choosing Between Standalone and Networked Smart Locks for Campsites, Glamping and Park Lodges takes that decision in full for a site where the power and the signal are as thin as the budget.

Who signs the schedule? The property manager owns the fit verdict and the maintenance route, the operator owns the credential and the logging position, the fire authority owns the escape-route answers, and the survey is complete only when all three are represented on it.

Where a campsite survey leads

A finished campsite survey is not a hardware list. It is a per-door statement about three things: whether a lock can physically live on that leaf, whether the site can maintain it without a specialist, and whether the credential on it can be voided when the season turns. That statement is what makes a campsite programme defensible in a season where the population changes twice and the labour changes with it.

The next decisions follow from the survey rather than preceding it. Whether the programme is phased across a portfolio of sites, and how the first wave is chosen, is in Phased Retrofit: Smart Locks Across a Campsites, Glamping and Park Lodges Portfolio; how a site with twenty doors and a site with two hundred are scoped differently is in Illustrative 20-300 Units Smart Lock Programme for Campsites, Glamping and Park Lodges: Scope Notes; and what a failed lock looks like at eight in the morning in the wet season is in Smart Lock Failure Triage for Campsites, Glamping and Park Lodges.

Send the door schedule rather than the door count, and ask for the samples against the specific leaf classes that failed the fit test rather than against the total. Sample handling is arranged through order samples and pricing through request a quote, with the factory-side checklist for those samples in the Smart Lock Factory Sample Testing Guide. Send the schedule with the dated season, the exposure column filled in and the open questions named, because that is the document a supplier can work from and a warden can act on.

Winkelwagen
Uw ervaring op deze site wordt verbeterd door cookies toe te staan Cookiebeleid
Chat on WhatsApp