Slk 118 specification decode: decode the SLK-118 data sheet into procurement-ready comparisons, evidence requests, door-fit checks, credential workflow.

Pubblicato il: giu 23, 2023

What the SLK-118 Data Sheet Actually Tells a Buyer

What the SLK-118 Data Sheet Actually Tells a Buyer

This slk 118 specification decode starts with a simple rule: a specification sheet is evidence, not an acceptance decision. The supplied SLK-118 record tells a procurement manager what the factory catalogue says about access, management software, lock construction, power, packing and documentation. It does not, by itself, close the project questions raised by those fields. A buyer should separate three layers: a value actually recorded for SLK-118, a value that differs or is blank, and evidence that must be dated and tied to the ordered SKU.

Direct answer. Condensed to the essential point, slk 118 specification decode turns a request into a decision record. slk 118 specification decode and slk-118 are the two parts of slk 118 specification decode most often skipped. A slk 118 specification decode describes how one component behaves under load. The datasheet makes claims. slk 118 specification decode is what slk 118 specification decode can be tested against.

  • Check the capability — confirm on the dated product page for the specific SKU behind slk 118 specification decode
  • Check the limit — record where the technology in slk-118 stops working
  • Check the fallback — name the mechanical path that remains if slk 118 specification decode fails
  • In slk 118 specification decode, this sequence is what slk 118 is checked against.

That separation matters because a hotel lock data sheet can look complete at a glance while leaving the costly decisions unresolved. The record provides a panel size and a No. 2 hotel mortise, but the door-fit field is blank. It lists guest card issuance and unlock records, while the capacity and environment fields are blank. The useful result is therefore a conditional shortlist with an evidence plan, not an unconditional purchase order.

Read the sheet as an evidence ladder

A responsible slk 118 specification decode follows the evidence from general catalogue information to SKU-specific project proof. The catalogue row identifies what the factory has recorded. The dated product page for the specific SKU is the next reference point. Dimension drawings and the installation guide then turn body specifications into geometry. Finally, the buyer's own door measurements and operating requirements determine whether the recorded product belongs in the project.

flowchart TD
    A[Read catalogue fields] --> B[Check dated SKU evidence]
    B --> C{Required field is blank}
    C -->|Yes| D[Request proof and hold approval]
    C -->|No| E[Compare project fit]
    D --> E
    E --> F[Make a conditional decision]
Evidence layerWhat it can establishAcceptance rule
Supplied catalogue rowThe recorded product scope and populated fieldsTreat it as the starting point, not final approval
Dated product pageThe current SKU-specific statementConfirm on the dated product page for the specific SKU
Dimension drawingsPanel, mortise and installation geometryMatch against recorded door measurements
Project measurementsThe actual installation conditionsRetain the measured evidence with the approval file

This sequence prevents two opposite errors: rejecting a viable product because one value is absent, or approving it because its record contains persuasive words. A blank field needs evidence; a populated field needs confirmation.

What the SLK-118 record establishes

The catalogue presents the SLK-118 RFID card lock as a hotel lock with an RFID/IC card, a mechanical override, PC hotel lock management software and a standalone operating arrangement. The recorded hardware includes a 201 stainless steel body and panel, a No. 2 hotel mortise, a 242 × 77 × 19 mm panel and silver or gold finishes.

Recorded groupSLK-118 catalogue valueProcurement interpretation
AccessRFID/IC card and mechanical overrideTwo access routes are recorded for project confirmation
PlatformHotel lock management software for PCAsk how cards are issued, changed and audited
Network arrangementStandalone lock with a PC-linked card encoderClarify the operating topology before approving it
Management functionsGuest card issuance, floor/room permissions, check-in validity windows and unlock recordsThese are workflow functions to test against project rules
StyleRFID Hotel Card LockConfirms the recorded product category, not installation suitability
Material201 stainless steelA body specification, not a project-wide finish decision
MortiseNo. 2 hotel mortiseObtain the applicable dimension drawing before ordering
Panel242 × 77 × 19 mmCompare with the door and frame, not against the mortise alone
FinishSilver or GoldA recorded option that must be tied to the ordered configuration
Power4 × AA alkaline batteries with a low-battery alertReview the service procedure and battery specification
Packing570 × 355 × 346 mm carton, 10 units per carton and 23.15 kg gross weightUse for handling and packing review
Door fitNo catalogue entryTreat compatibility as unestablished until drawings and measurements agree
Capacity and versionsNo catalogue entryAsk for the applicable configuration and user limits
EnvironmentNo catalogue entryRequest the relevant environmental limits for the installation
ServicesDimension drawings, installation guide and full datasheet on requestObtain all three for the selected SKU

The field marked “Standard” in the access and power rows means that the capability is present in the catalogue record. It is not a substitute for a procurement confirmation. Before dimensions, power or workflow details drive an order, confirm on the dated product page for the specific SKU.

The services row is particularly useful. The catalogue says that dimension drawings, an installation guide and the full datasheet are available on request, while the OEM/ODM scope covers logo, finish, packaging, manuals and product configuration for distributor and project orders. Those documents define what the buyer can verify and what can be customized.

SLK-118 vs SLK-118E: where the records separate

The direct comparison is narrower than the model names might suggest. The supplied records share the same access fields, management platform, body, mortise, panel, finishes, power arrangement, carton dimensions, units per carton and documentation scope. Their visible packing-data difference is gross carton weight: 23.15 kg for SLK-118 and 23.6 kg for SLK-118E.

Comparison pointSLK-118SLK-118EWhat the buyer should conclude
Catalogue nameRFID Card Lock for Hotels and B&BsKeypad Hotel Combination Lock for Wooden DoorsNames describe different positioning, but the supplied Access rows do not provide matching detail
RFID/IC cardRecorded as standardRecorded as standardConfirm the credential format and issuance workflow for the selected SKU
Passcode/keypad fieldNot listed in the supplied Access rowNot listed in the supplied Access row, despite the catalogue nameDo not turn the SLK-118E name into a verified keypad specification
Mechanical overrideRecorded as standardRecorded as standardVerify the supplied key and its installation details
Management softwarePC hotel lock management softwarePC hotel lock management softwareThe same platform fields are recorded for both
Card encoderPC-linked card encoderPC-linked card encoderAsk for the exact encoder and accessory scope
Body and panel201 stainless steel; No. 2 hotel mortise; 242 × 77 × 19 mm panelSame recorded valuesDoor fit still requires drawings because both Door fit fields are blank
Power4 × AA alkaline batteries; low-battery alert4 × AA alkaline batteries; low-battery alertReview the service procedure for either model
Carton570 × 355 × 346 mm; 10 units; 23.15 kg570 × 355 × 346 mm; 10 units; 23.6 kgBoth can be included in handling and receiving plans
DocumentationDrawings, installation guide and datasheet on requestDrawings, installation guide and datasheet on requestRequest the documents against the exact model

The SLK-118E naming discrepancy is the central warning in this SLK-118 vs SLK-118E arena. Its catalogue name refers to a keypad hotel combination lock for wooden doors, while the supplied Access row lists RFID/IC card and mechanical override only. The conservative procurement reading is that the row provides no verified passcode/keypad entry for the buyer to approve.

Likewise, the SLK-118E name mentions wooden doors, but its Door fit field contains no catalogue entry. A name is not a cutting template. Ask for the dimension drawing and compare it with the actual door before placing SLK-118E in a project-specific shortlist.

Read access, software and network as one operating chain

The SLK-118 access and platform fields describe an operating chain rather than isolated features. A guest card is issued through the PC-linked card encoder, permissions and validity windows are applied through the management software, the lock records an unlock, and the mechanical override provides a separately recorded route when normal card use is unavailable. Each arrow in that chain needs project-specific confirmation.

Recorded functionQuestion the buyer must askEvidence to request
RFID/IC cardWhich card format and encoding process apply to the ordered configuration?Current credential specification and sample issuance procedure
Guest card issuanceWho can issue, cancel and replace a guest card, and where is that workstation?Software workflow description and encoder identification
Floor/room permissionsHow are access boundaries configured and checked?Permission examples tied to the proposed hotel structure
Check-in validity windowsHow are arrival, departure and expiry rules represented?A workflow example using the project's actual timing rules
Unlock recordsWhere are records retained, exported and reviewed?Record structure, export method and operating responsibility
Mechanical overrideWhich key is supplied, and how is key control assigned?Key schedule and supplied-accessory list

The catalogue's “no in-room network required” statement belongs in the same review. It tells the buyer that the recorded arrangement does not require an in-room network. It does not explain the full operating workflow, the location of the PC, the consequences of a workstation outage, or how staff permissions are administered. Those are questions for the software and installation evidence.

SLK-118 Credential and Software Configuration Options expands the configuration choices separately. For a competitive review, use that discussion to define the workflow first, then ask the supplier which recorded SLK-118 fields satisfy it.

CONFIRM-WITH-LOCAL-ACCESS-PRIVACY-REVIEW: Verify locally applicable requirements for guest-cardholder records, unlock-log handling, staff access, retention and project approval before selecting the operating workflow.

Hotel lock door fit begins with geometry

Hotel lock door fit cannot be approved from the panel dimensions alone. The SLK-118 record gives a 242 × 77 × 19 mm panel and a No. 2 hotel mortise, but no populated door-fit information. The drawing still has to be matched with the door leaf, frame rebate, backset, spindle position, cylinder position, strike plate and keeper, plus the panel's relationship to the door edge and swing.

Geometry itemWhy the buyer needs itEvidence to retain
Door leaf thicknessDetermines whether the panel and mortise can be installed as drawnMeasurement at several points on the door
Frame rebate width and depthDefines the space available to the lock bodyDimensioned site record and drawing comparison
BacksetConnects the chosen mortise to the edge of the doorExisting and required measurements
Spindle and cylinder positionsControl handle and override alignmentDrawing overlay against the door
Strike plate and keeperDetermine latch engagement in the frameFrame condition and hardware dimensions
Panel envelopeChecks projection, lever clearance and adjacent finishesScaled drawing or physical template

The dimensions should be handled as a fit exercise, not a model-name exercise. The SLK-118 Door Fit and Replacement Notes for Buyers companion article provides the model-specific reading task. For the measurement workflow, the Smart Lock Retrofit Site Survey and Office Smart Lock Site Survey provide useful survey structures that can be adapted to guest-room doors.

Before approving either SLK-118 or SLK-118E for a particular door, obtain the applicable dimension drawing and installation guide.

Power and packing are recorded, but service planning remains

The power rows are simple: both records state 4 × AA alkaline batteries and a low-battery alert. The buyer still needs to turn that into an operating procedure. The catalogue does not provide a battery-life figure, so the assessment should focus on maintenance ownership, replacement access, alert visibility and the process for using the recorded mechanical override.

Power decisionCatalogue evidenceBuyer follow-up
Power source4 × AA alkaline batteriesConfirm the approved battery specification for the SKU and project
Low-battery indicationLow-battery alert recordedAsk how the alert is presented and who acts on it
Battery replacementNo procedure recordedRequest an installation and maintenance instruction
Mechanical fallbackMechanical override recordedVerify the supplied key and local key-control process
Operating conditionsEnvironment field has no catalogue entryRequest the environmental limits relevant to the installation

The packing data is more concrete. Both models use a 570 × 355 × 346 mm carton with 10 units per carton. Gross weight is 23.15 kg for SLK-118 and 23.6 kg for SLK-118E.

Packing inputSLK-118SLK-118EUse in the comparison
Carton dimensions570 × 355 × 346 mm570 × 355 × 346 mmCheck receiving, storage and handling space
Units per carton1010Plan carton counts against the approved project quantity
Gross weight per carton23.15 kg23.6 kgInclude the difference in manual-handling review
Export-carton configurationRecordedRecordedConfirm the final packed configuration with the supplier

These values support physical planning, but they are not a complete logistics instruction. Ask for carton labels, packing method, handling marks and the packing configuration tied to the ordered finish and accessories. Treat all recorded dimensions and weights as subject to confirmation on the dated product page for the specific SKU.

Blank fields and naming conflicts require conservative reading

The catalogue's em dash is an absence, not an invitation to fill the gap with a marketing assumption. For SLK-118, the Door fit, Capacity & versions, and Environment groups contain no catalogue entry. The same pattern appears for SLK-118E. The buyer should identify what evidence is required instead of converting an absence into a favourable assumption.

Issue in the supplied recordConservative readingEvidence needed
No SLK-118 Door fit entryThe catalogue does not establish door compatibilityDimension drawings, installation guide and site measurements
No SLK-118E Door fit entry despite “wooden doors” in the nameThe name does not establish the required door geometryCurrent drawings and a door-by-door comparison
No capacity or versions entriesUser limits and available configurations are not establishedCurrent configuration sheet for the selected SKU
No environment entriesWeather and temperature/humidity limits are not establishedEnvironmental specification for the installation
SLK-118E name refers to keypad, but Access omits passcode/keypadThe current row does not provide verified keypad evidenceDated SKU page and credential-method description
No low-battery procedure detailAn alert exists, but the response process is not definedInstallation, maintenance and staff operating instructions

This approach is especially useful in a comparison arena. One model should not win because its catalogue wording is more persuasive. Each model should receive the same evidence request and the same pass, hold or exclude decision. A missing mandatory field creates a hold until evidence arrives; it does not automatically create a rejection, and it never creates an approval by itself.

A hotel lock procurement checklist that turns the sheets

The following hotel lock procurement checklist is a worksheet, not a product rating. The weights are buyer-defined examples and sum to 100; replace them according to the project. “Verify” means the catalogue contains a populated field that must be confirmed for the selected SKU. “Hold” means approval waits for evidence. Neither label says that the product passes or fails.

Evaluation criterionBuyer-defined weightSLK-118 recordSLK-118E recordDecision treatment
Credential route25RFID/IC card recordedName refers to keypad; Access row omits passcode/keypadSLK-118: verify; SLK-118E: hold pending clarification
Door-fit evidence25Door fit absentDoor fit absentHold both until drawings and measurements agree
Management workflow20PC software and encoder recordedPC software and encoder recordedVerify against the required guest-card process
Power and service104 × AA and alert recorded4 × AA and alert recordedVerify battery and alert details
Packing and handling5Carton data recordedCarton data recordedVerify final packed configuration
Documentation and OEM scope15Drawings, guide, datasheet and configuration scope recordedSame documented scope recordedVerify what the selected order receives

Turn that scorecard into an evidence request rather than a spreadsheet exercise. Each response should name the model, carry a current date and identify whether it applies to the exact configuration being considered.

Evidence itemIt must answerApproval owner
Dated product-page extractWhich populated values and options apply to the selected SKU?Procurement manager
Dimension drawingDoes the mortise and panel geometry match the measured door?Installer or site-survey lead
Installation guideWhat installation conditions and steps apply?Technical evaluator
Full datasheetWhat are the complete technical and configuration fields?Engineer or product evaluator
Credential and encoder packHow is guest card issuance performed, and what equipment is supplied?Operations owner
Software workflow evidenceHow are permissions, validity windows and unlock records managed?Operations and IT reviewers
Packing specificationWhat carton, unit count, weight and accessories will be supplied?Logistics reviewer

The SLK-118 Purchase-Order Checklist: What to Confirm Before Ordering provides the place to convert these evidence items into order conditions. Keep every accepted document, approved configuration and measurement sheet with the purchase record so that the final comparison remains auditable.

Run the comparison through an illustrative hotel scenario

Consider an illustrative small hotel or B&B refurbishment where guest-room doors are being surveyed, staff issue cards from a front-desk PC and the project team is deciding between SLK-118 and SLK-118E. No product has been installed and no project outcome is being reported. The purpose is to show how the records control the shortlist.

Decision questionSLK-118 pathSLK-118E path
Does the required guest credential route have recorded evidence?RFID/IC card is recorded; verify the current card and encoder detailsHold while the keypad wording is reconciled with the Access row
Can the lock be fitted to the surveyed wooden doors?Obtain drawings and compare the panel and No. 2 mortise with every door typeObtain drawings; do not rely on the name alone
Does the management workflow match front-desk operations?Test guest card issuance, permissions, validity windows and unlock recordsTest the same workflow against the confirmed credential method
Can maintenance be planned from the power data?Verify 4 × AA alkaline supply and the low-battery alert procedureApply the same evidence request to the confirmed SKU
Is the order package complete?Add the SLK-118 drawing, guide, datasheet and packing confirmation to the order fileAdd the same package plus evidence resolving the naming discrepancy

The first decision is not “Which name sounds right?” It is “Which documented configuration matches the operating requirement?” If the project needs card-based guest access and the site measurements accept the SLK-118 geometry, SLK-118 remains a credible conditional candidate. If the project needs a specific keypad method, SLK-118E cannot advance on its catalogue name until the Access record is reconciled. If either door or workflow evidence fails, the comparison stops.

This illustrative sequence also prevents scope mixing. The door-fit article answers geometry, the credential article answers software and issuance, and the purchase-order checklist controls what must be confirmed before commitment. The data sheet should connect those workstreams, not replace them.

The final decision is a documented conditional outcome

The supplied SLK-118 record tells a buyer what is recorded: RFID/IC card and mechanical override access; PC hotel lock management software; a PC-linked card encoder; guest card issuance, floor/room permissions, check-in validity windows and unlock records; 201 stainless steel; a No. 2 hotel mortise; a 242 × 77 × 19 mm panel; silver or gold finishes; 4 × AA alkaline power with a low-battery alert; and defined carton packing. It also says that dimension drawings, an installation guide and a full datasheet are available on request.

It leaves other questions open. Door fit has no populated entry. Capacity, versions and environment have no catalogue entries. The SLK-118E name and Access row require reconciliation before a keypad method can be treated as verified. Those are procurement findings, not weaknesses to be hidden with assumptions.

Apply three final gates. Approve only when the selected SKU, configuration, measurements and operating workflow agree. Hold any model whose missing field is mandatory to the project. Exclude a route when the buyer requires evidence that the supplier cannot provide for that configuration.

The same question is worked through in more detail in bluetooth smart locks for commercial applications. That is the same question slk 118 specification decode has to answer here.Once the evidence pack is tied to the selected model, request the catalogue, current SKU information and a project quotation through the request-catalog and request-a-quote routes. The recorded OEM/ODM scope for SLK-118 includes custom logo, finish, packaging, manuals and product configuration for distributor and project orders. Confirm which changes belong in the final order, then close the comparison with the approved evidence attached rather than a copied specification paragraph.

Il tuo carrello
La tua esperienza su questo sito sarà migliorata consentendo i cookie Informativa sui cookie
Chat on WhatsApp