What the SLK-118 Data Sheet Actually Tells a Buyer
This slk 118 specification decode starts with a simple rule: a specification sheet is evidence, not an acceptance decision. The supplied SLK-118 record tells a procurement manager what the factory catalogue says about access, management software, lock construction, power, packing and documentation. It does not, by itself, close the project questions raised by those fields. A buyer should separate three layers: a value actually recorded for SLK-118, a value that differs or is blank, and evidence that must be dated and tied to the ordered SKU.
Direct answer. Condensed to the essential point, slk 118 specification decode turns a request into a decision record. slk 118 specification decode and slk-118 are the two parts of slk 118 specification decode most often skipped. A slk 118 specification decode describes how one component behaves under load. The datasheet makes claims. slk 118 specification decode is what slk 118 specification decode can be tested against.
- Check the capability — confirm on the dated product page for the specific SKU behind slk 118 specification decode
- Check the limit — record where the technology in slk-118 stops working
- Check the fallback — name the mechanical path that remains if slk 118 specification decode fails
- In slk 118 specification decode, this sequence is what slk 118 is checked against.
That separation matters because a hotel lock data sheet can look complete at a glance while leaving the costly decisions unresolved. The record provides a panel size and a No. 2 hotel mortise, but the door-fit field is blank. It lists guest card issuance and unlock records, while the capacity and environment fields are blank. The useful result is therefore a conditional shortlist with an evidence plan, not an unconditional purchase order.
Read the sheet as an evidence ladder
A responsible slk 118 specification decode follows the evidence from general catalogue information to SKU-specific project proof. The catalogue row identifies what the factory has recorded. The dated product page for the specific SKU is the next reference point. Dimension drawings and the installation guide then turn body specifications into geometry. Finally, the buyer's own door measurements and operating requirements determine whether the recorded product belongs in the project.
flowchart TD
A[Read catalogue fields] --> B[Check dated SKU evidence]
B --> C{Required field is blank}
C -->|Yes| D[Request proof and hold approval]
C -->|No| E[Compare project fit]
D --> E
E --> F[Make a conditional decision]
| Evidence layer | What it can establish | Acceptance rule |
|---|---|---|
| Supplied catalogue row | The recorded product scope and populated fields | Treat it as the starting point, not final approval |
| Dated product page | The current SKU-specific statement | Confirm on the dated product page for the specific SKU |
| Dimension drawings | Panel, mortise and installation geometry | Match against recorded door measurements |
| Project measurements | The actual installation conditions | Retain the measured evidence with the approval file |
This sequence prevents two opposite errors: rejecting a viable product because one value is absent, or approving it because its record contains persuasive words. A blank field needs evidence; a populated field needs confirmation.
What the SLK-118 record establishes
The catalogue presents the SLK-118 RFID card lock as a hotel lock with an RFID/IC card, a mechanical override, PC hotel lock management software and a standalone operating arrangement. The recorded hardware includes a 201 stainless steel body and panel, a No. 2 hotel mortise, a 242 × 77 × 19 mm panel and silver or gold finishes.
| Recorded group | SLK-118 catalogue value | Procurement interpretation |
|---|---|---|
| Access | RFID/IC card and mechanical override | Two access routes are recorded for project confirmation |
| Platform | Hotel lock management software for PC | Ask how cards are issued, changed and audited |
| Network arrangement | Standalone lock with a PC-linked card encoder | Clarify the operating topology before approving it |
| Management functions | Guest card issuance, floor/room permissions, check-in validity windows and unlock records | These are workflow functions to test against project rules |
| Style | RFID Hotel Card Lock | Confirms the recorded product category, not installation suitability |
| Material | 201 stainless steel | A body specification, not a project-wide finish decision |
| Mortise | No. 2 hotel mortise | Obtain the applicable dimension drawing before ordering |
| Panel | 242 × 77 × 19 mm | Compare with the door and frame, not against the mortise alone |
| Finish | Silver or Gold | A recorded option that must be tied to the ordered configuration |
| Power | 4 × AA alkaline batteries with a low-battery alert | Review the service procedure and battery specification |
| Packing | 570 × 355 × 346 mm carton, 10 units per carton and 23.15 kg gross weight | Use for handling and packing review |
| Door fit | No catalogue entry | Treat compatibility as unestablished until drawings and measurements agree |
| Capacity and versions | No catalogue entry | Ask for the applicable configuration and user limits |
| Environment | No catalogue entry | Request the relevant environmental limits for the installation |
| Services | Dimension drawings, installation guide and full datasheet on request | Obtain all three for the selected SKU |
The field marked “Standard” in the access and power rows means that the capability is present in the catalogue record. It is not a substitute for a procurement confirmation. Before dimensions, power or workflow details drive an order, confirm on the dated product page for the specific SKU.
The services row is particularly useful. The catalogue says that dimension drawings, an installation guide and the full datasheet are available on request, while the OEM/ODM scope covers logo, finish, packaging, manuals and product configuration for distributor and project orders. Those documents define what the buyer can verify and what can be customized.
SLK-118 vs SLK-118E: where the records separate
The direct comparison is narrower than the model names might suggest. The supplied records share the same access fields, management platform, body, mortise, panel, finishes, power arrangement, carton dimensions, units per carton and documentation scope. Their visible packing-data difference is gross carton weight: 23.15 kg for SLK-118 and 23.6 kg for SLK-118E.
| Comparison point | SLK-118 | SLK-118E | What the buyer should conclude |
|---|---|---|---|
| Catalogue name | RFID Card Lock for Hotels and B&Bs | Keypad Hotel Combination Lock for Wooden Doors | Names describe different positioning, but the supplied Access rows do not provide matching detail |
| RFID/IC card | Recorded as standard | Recorded as standard | Confirm the credential format and issuance workflow for the selected SKU |
| Passcode/keypad field | Not listed in the supplied Access row | Not listed in the supplied Access row, despite the catalogue name | Do not turn the SLK-118E name into a verified keypad specification |
| Mechanical override | Recorded as standard | Recorded as standard | Verify the supplied key and its installation details |
| Management software | PC hotel lock management software | PC hotel lock management software | The same platform fields are recorded for both |
| Card encoder | PC-linked card encoder | PC-linked card encoder | Ask for the exact encoder and accessory scope |
| Body and panel | 201 stainless steel; No. 2 hotel mortise; 242 × 77 × 19 mm panel | Same recorded values | Door fit still requires drawings because both Door fit fields are blank |
| Power | 4 × AA alkaline batteries; low-battery alert | 4 × AA alkaline batteries; low-battery alert | Review the service procedure for either model |
| Carton | 570 × 355 × 346 mm; 10 units; 23.15 kg | 570 × 355 × 346 mm; 10 units; 23.6 kg | Both can be included in handling and receiving plans |
| Documentation | Drawings, installation guide and datasheet on request | Drawings, installation guide and datasheet on request | Request the documents against the exact model |
The SLK-118E naming discrepancy is the central warning in this SLK-118 vs SLK-118E arena. Its catalogue name refers to a keypad hotel combination lock for wooden doors, while the supplied Access row lists RFID/IC card and mechanical override only. The conservative procurement reading is that the row provides no verified passcode/keypad entry for the buyer to approve.
Likewise, the SLK-118E name mentions wooden doors, but its Door fit field contains no catalogue entry. A name is not a cutting template. Ask for the dimension drawing and compare it with the actual door before placing SLK-118E in a project-specific shortlist.
Read access, software and network as one operating chain
The SLK-118 access and platform fields describe an operating chain rather than isolated features. A guest card is issued through the PC-linked card encoder, permissions and validity windows are applied through the management software, the lock records an unlock, and the mechanical override provides a separately recorded route when normal card use is unavailable. Each arrow in that chain needs project-specific confirmation.
| Recorded function | Question the buyer must ask | Evidence to request |
|---|---|---|
| RFID/IC card | Which card format and encoding process apply to the ordered configuration? | Current credential specification and sample issuance procedure |
| Guest card issuance | Who can issue, cancel and replace a guest card, and where is that workstation? | Software workflow description and encoder identification |
| Floor/room permissions | How are access boundaries configured and checked? | Permission examples tied to the proposed hotel structure |
| Check-in validity windows | How are arrival, departure and expiry rules represented? | A workflow example using the project's actual timing rules |
| Unlock records | Where are records retained, exported and reviewed? | Record structure, export method and operating responsibility |
| Mechanical override | Which key is supplied, and how is key control assigned? | Key schedule and supplied-accessory list |
The catalogue's “no in-room network required” statement belongs in the same review. It tells the buyer that the recorded arrangement does not require an in-room network. It does not explain the full operating workflow, the location of the PC, the consequences of a workstation outage, or how staff permissions are administered. Those are questions for the software and installation evidence.
SLK-118 Credential and Software Configuration Options expands the configuration choices separately. For a competitive review, use that discussion to define the workflow first, then ask the supplier which recorded SLK-118 fields satisfy it.
CONFIRM-WITH-LOCAL-ACCESS-PRIVACY-REVIEW: Verify locally applicable requirements for guest-cardholder records, unlock-log handling, staff access, retention and project approval before selecting the operating workflow.
Hotel lock door fit begins with geometry
Hotel lock door fit cannot be approved from the panel dimensions alone. The SLK-118 record gives a 242 × 77 × 19 mm panel and a No. 2 hotel mortise, but no populated door-fit information. The drawing still has to be matched with the door leaf, frame rebate, backset, spindle position, cylinder position, strike plate and keeper, plus the panel's relationship to the door edge and swing.
| Geometry item | Why the buyer needs it | Evidence to retain |
|---|---|---|
| Door leaf thickness | Determines whether the panel and mortise can be installed as drawn | Measurement at several points on the door |
| Frame rebate width and depth | Defines the space available to the lock body | Dimensioned site record and drawing comparison |
| Backset | Connects the chosen mortise to the edge of the door | Existing and required measurements |
| Spindle and cylinder positions | Control handle and override alignment | Drawing overlay against the door |
| Strike plate and keeper | Determine latch engagement in the frame | Frame condition and hardware dimensions |
| Panel envelope | Checks projection, lever clearance and adjacent finishes | Scaled drawing or physical template |
The dimensions should be handled as a fit exercise, not a model-name exercise. The SLK-118 Door Fit and Replacement Notes for Buyers companion article provides the model-specific reading task. For the measurement workflow, the Smart Lock Retrofit Site Survey and Office Smart Lock Site Survey provide useful survey structures that can be adapted to guest-room doors.
Before approving either SLK-118 or SLK-118E for a particular door, obtain the applicable dimension drawing and installation guide.
Power and packing are recorded, but service planning remains
The power rows are simple: both records state 4 × AA alkaline batteries and a low-battery alert. The buyer still needs to turn that into an operating procedure. The catalogue does not provide a battery-life figure, so the assessment should focus on maintenance ownership, replacement access, alert visibility and the process for using the recorded mechanical override.
| Power decision | Catalogue evidence | Buyer follow-up |
|---|---|---|
| Power source | 4 × AA alkaline batteries | Confirm the approved battery specification for the SKU and project |
| Low-battery indication | Low-battery alert recorded | Ask how the alert is presented and who acts on it |
| Battery replacement | No procedure recorded | Request an installation and maintenance instruction |
| Mechanical fallback | Mechanical override recorded | Verify the supplied key and local key-control process |
| Operating conditions | Environment field has no catalogue entry | Request the environmental limits relevant to the installation |
The packing data is more concrete. Both models use a 570 × 355 × 346 mm carton with 10 units per carton. Gross weight is 23.15 kg for SLK-118 and 23.6 kg for SLK-118E.
| Packing input | SLK-118 | SLK-118E | Use in the comparison |
|---|---|---|---|
| Carton dimensions | 570 × 355 × 346 mm | 570 × 355 × 346 mm | Check receiving, storage and handling space |
| Units per carton | 10 | 10 | Plan carton counts against the approved project quantity |
| Gross weight per carton | 23.15 kg | 23.6 kg | Include the difference in manual-handling review |
| Export-carton configuration | Recorded | Recorded | Confirm the final packed configuration with the supplier |
These values support physical planning, but they are not a complete logistics instruction. Ask for carton labels, packing method, handling marks and the packing configuration tied to the ordered finish and accessories. Treat all recorded dimensions and weights as subject to confirmation on the dated product page for the specific SKU.
Blank fields and naming conflicts require conservative reading
The catalogue's em dash is an absence, not an invitation to fill the gap with a marketing assumption. For SLK-118, the Door fit, Capacity & versions, and Environment groups contain no catalogue entry. The same pattern appears for SLK-118E. The buyer should identify what evidence is required instead of converting an absence into a favourable assumption.
| Issue in the supplied record | Conservative reading | Evidence needed |
|---|---|---|
| No SLK-118 Door fit entry | The catalogue does not establish door compatibility | Dimension drawings, installation guide and site measurements |
| No SLK-118E Door fit entry despite “wooden doors” in the name | The name does not establish the required door geometry | Current drawings and a door-by-door comparison |
| No capacity or versions entries | User limits and available configurations are not established | Current configuration sheet for the selected SKU |
| No environment entries | Weather and temperature/humidity limits are not established | Environmental specification for the installation |
| SLK-118E name refers to keypad, but Access omits passcode/keypad | The current row does not provide verified keypad evidence | Dated SKU page and credential-method description |
| No low-battery procedure detail | An alert exists, but the response process is not defined | Installation, maintenance and staff operating instructions |
This approach is especially useful in a comparison arena. One model should not win because its catalogue wording is more persuasive. Each model should receive the same evidence request and the same pass, hold or exclude decision. A missing mandatory field creates a hold until evidence arrives; it does not automatically create a rejection, and it never creates an approval by itself.
A hotel lock procurement checklist that turns the sheets
The following hotel lock procurement checklist is a worksheet, not a product rating. The weights are buyer-defined examples and sum to 100; replace them according to the project. “Verify” means the catalogue contains a populated field that must be confirmed for the selected SKU. “Hold” means approval waits for evidence. Neither label says that the product passes or fails.
| Evaluation criterion | Buyer-defined weight | SLK-118 record | SLK-118E record | Decision treatment |
|---|---|---|---|---|
| Credential route | 25 | RFID/IC card recorded | Name refers to keypad; Access row omits passcode/keypad | SLK-118: verify; SLK-118E: hold pending clarification |
| Door-fit evidence | 25 | Door fit absent | Door fit absent | Hold both until drawings and measurements agree |
| Management workflow | 20 | PC software and encoder recorded | PC software and encoder recorded | Verify against the required guest-card process |
| Power and service | 10 | 4 × AA and alert recorded | 4 × AA and alert recorded | Verify battery and alert details |
| Packing and handling | 5 | Carton data recorded | Carton data recorded | Verify final packed configuration |
| Documentation and OEM scope | 15 | Drawings, guide, datasheet and configuration scope recorded | Same documented scope recorded | Verify what the selected order receives |
Turn that scorecard into an evidence request rather than a spreadsheet exercise. Each response should name the model, carry a current date and identify whether it applies to the exact configuration being considered.
| Evidence item | It must answer | Approval owner |
|---|---|---|
| Dated product-page extract | Which populated values and options apply to the selected SKU? | Procurement manager |
| Dimension drawing | Does the mortise and panel geometry match the measured door? | Installer or site-survey lead |
| Installation guide | What installation conditions and steps apply? | Technical evaluator |
| Full datasheet | What are the complete technical and configuration fields? | Engineer or product evaluator |
| Credential and encoder pack | How is guest card issuance performed, and what equipment is supplied? | Operations owner |
| Software workflow evidence | How are permissions, validity windows and unlock records managed? | Operations and IT reviewers |
| Packing specification | What carton, unit count, weight and accessories will be supplied? | Logistics reviewer |
The SLK-118 Purchase-Order Checklist: What to Confirm Before Ordering provides the place to convert these evidence items into order conditions. Keep every accepted document, approved configuration and measurement sheet with the purchase record so that the final comparison remains auditable.
Run the comparison through an illustrative hotel scenario
Consider an illustrative small hotel or B&B refurbishment where guest-room doors are being surveyed, staff issue cards from a front-desk PC and the project team is deciding between SLK-118 and SLK-118E. No product has been installed and no project outcome is being reported. The purpose is to show how the records control the shortlist.
| Decision question | SLK-118 path | SLK-118E path |
|---|---|---|
| Does the required guest credential route have recorded evidence? | RFID/IC card is recorded; verify the current card and encoder details | Hold while the keypad wording is reconciled with the Access row |
| Can the lock be fitted to the surveyed wooden doors? | Obtain drawings and compare the panel and No. 2 mortise with every door type | Obtain drawings; do not rely on the name alone |
| Does the management workflow match front-desk operations? | Test guest card issuance, permissions, validity windows and unlock records | Test the same workflow against the confirmed credential method |
| Can maintenance be planned from the power data? | Verify 4 × AA alkaline supply and the low-battery alert procedure | Apply the same evidence request to the confirmed SKU |
| Is the order package complete? | Add the SLK-118 drawing, guide, datasheet and packing confirmation to the order file | Add the same package plus evidence resolving the naming discrepancy |
The first decision is not “Which name sounds right?” It is “Which documented configuration matches the operating requirement?” If the project needs card-based guest access and the site measurements accept the SLK-118 geometry, SLK-118 remains a credible conditional candidate. If the project needs a specific keypad method, SLK-118E cannot advance on its catalogue name until the Access record is reconciled. If either door or workflow evidence fails, the comparison stops.
This illustrative sequence also prevents scope mixing. The door-fit article answers geometry, the credential article answers software and issuance, and the purchase-order checklist controls what must be confirmed before commitment. The data sheet should connect those workstreams, not replace them.
The final decision is a documented conditional outcome
The supplied SLK-118 record tells a buyer what is recorded: RFID/IC card and mechanical override access; PC hotel lock management software; a PC-linked card encoder; guest card issuance, floor/room permissions, check-in validity windows and unlock records; 201 stainless steel; a No. 2 hotel mortise; a 242 × 77 × 19 mm panel; silver or gold finishes; 4 × AA alkaline power with a low-battery alert; and defined carton packing. It also says that dimension drawings, an installation guide and a full datasheet are available on request.
It leaves other questions open. Door fit has no populated entry. Capacity, versions and environment have no catalogue entries. The SLK-118E name and Access row require reconciliation before a keypad method can be treated as verified. Those are procurement findings, not weaknesses to be hidden with assumptions.
Apply three final gates. Approve only when the selected SKU, configuration, measurements and operating workflow agree. Hold any model whose missing field is mandatory to the project. Exclude a route when the buyer requires evidence that the supplier cannot provide for that configuration.
The same question is worked through in more detail in bluetooth smart locks for commercial applications. That is the same question slk 118 specification decode has to answer here.Once the evidence pack is tied to the selected model, request the catalogue, current SKU information and a project quotation through the request-catalog and request-a-quote routes. The recorded OEM/ODM scope for SLK-118 includes custom logo, finish, packaging, manuals and product configuration for distributor and project orders. Confirm which changes belong in the final order, then close the comparison with the approved evidence attached rather than a copied specification paragraph.

