The Handle Is Not the Lock: Writing EN 1906 Into a Smart Lock RFQ
What follows is a working reference on en 1906 smart lock rfq clause, written for the buyer who must sign the submittal. A smart lock request for quotation that names EN 1906 is normally written by somebody who believes the lock has been covered. It has not. EN 1906 is a standard for lever handle and knob furniture — the grip a hand turns to open the door — and a document issued against it speaks to the durability of operation, the strength, the corrosion behaviour and the security of that furniture. It says nothing about the mechanism that retracts the bolt, nothing about a cylinder where the design has one, nothing about the escape function, and nothing about the radio.
The failure this produces is quiet, which is why it survives to handover. A certificate arrives, it is filed against the lock line, and the enclosure is marked as evidenced. Nobody objects at quotation stage, because nobody is looking for an objection. The gap appears when a consultant asks for the evidence covering the locking function and finds the only document in the file covers the handle.
Direct answer. An EN 1906 smart lock RFQ clause is finished when it does two separate jobs: it binds the handle or knob tightly enough that a supplier cannot substitute a finish or a geometry without notice, and it is written so that it can never be read as evidence about the lock. This guide builds the clause slot by slot, names the companion clause that must sit beside it, and shows where the boundary sentence goes so the furniture document stays where it belongs.
This is written for the procurement manager who issues the request for quotation and who will be held to the evidence afterwards, usually by a consultant, a tender assessor or an internal auditor.
What EN 1906 covers, and what it will never cover
EN 1906 covers lever handle and knob furniture. Its subject is the furniture and the furniture's own behaviour under use: durability of operation, strength, corrosion and security. Check the published title and the scope statement against the current edition before relying on any wording about it, because standards are revised and the exact set of properties inside the scope is settled by the published text, not by a summary.
Two things follow, and they pull in opposite directions. The first is what you can write: if the request for quotation names the furniture and asks for the document that demonstrates it, the clause can be precise and a supplier can answer it without guessing. The second is what the naming must not be allowed to imply.
A lock is not one object. A battery-driven smart lock on a real door contains a handle or knob, a lock case with a driving mechanism, often a cylinder, an escape function, a radio module, a power source and a set of credentials. EN 1906 speaks to the first of those. The rest are separate questions with separate evidence, and the one the standard knows about is rarely the one anybody was worried about. What the specification covers is in the smart door locks.
The commercial consequence is a drafting decision. A clause written at the level of "the product" reads as covering everything on the door. A clause written at the level of "the lever handle and knob furniture" reads as covering exactly that. Both read fine on the page. Only the second one survives a question.
Two habits compound this. The first is mis-citation: templates in circulation reach for a door-hardware standard whenever a door appears on a schedule, and EN 1935 — a standard for single-axis hinges — is cited as though it were a latch standard. The second is substitution in the other direction: a buyer holding mechanism evidence assumes the handle arrived with it, and the furniture becomes an unevidenced part of the order.
CONFIRM-WITH-LOCAL-STANDARDS-BODY — the published title, scope statement and current edition of EN 1906 in the market you are supplying, and which edition and amendment your national implementation refers to at the date of your order. Clause-level claims must be routed to the published standard text.
The mistake, in one sentence
The mistake is buying a lever-handle certificate and treating it as lock evidence. It is worth writing out in full, because each half fails differently.
| What the buyer believes | What the document actually says | Where the belief shows up |
|---|---|---|
| The lock is covered because the RFQ named EN 1906 | The document covers the furniture only — durability, strength, corrosion and security of the handle or knob | The evaluation sheet is ticked; the mechanism line has nothing behind it |
| One document per product | One document per object — furniture, mechanism, cylinder, escape, radio, environment | The file looks complete and is short several parts |
| The document names the model, so it covers the model | A type entry may list several furniture variants on a common body | A knob ships where a lever was quoted, against a document that never covered it |
| The supplier holds it, so the programme holds it | The holder may be unable or unwilling to confirm the scope later | The question becomes unanswerable at handover |
| The lock is covered, so the handle is covered | A mechanism document says nothing about the furniture | The furniture arrives unevidenced and nobody notices, because the enclosure was signed off |
None of this is dishonesty. It is an artefact of silence at clause level. A clause that does not say which object it governs leaves the object to be inferred, and the person inferring is usually the reader with the least context: an evaluator working down a checklist at the end of a long tender, or an auditor reading the file after it was assembled.
The fifth row is the mirror image and it is just as expensive. A programme holding mechanism evidence often assumes the handle is covered, so the furniture is ordered without a document at all. One clause, correctly scoped, closes both directions: it says what the furniture document covers, and that the locking function is governed by a different clause with its own evidence.
The questions a smart lock door actually asks
Before a clause can be written, the door has to be broken into questions. This is the part that usually gets skipped, and it is the part that makes an EN 1906 clause work or fail.
graph TD
Door["A smart lock on a real door"]
Door --> Q1["Furniture question"]
Door --> Q2["Lock mechanism question"]
Door --> Q3["Cylinder question"]
Door --> Q4["Escape function question"]
Door --> Q5["Radio and EMC question"]
Door --> Q6["Environment question"]
Door --> Q7["Fire assembly question"]
Q1 --> A1["EN 1906 document"]
Q2 --> A2["EN 14846 or EN 12209 document"]
Q3 --> A3["EN 1303 document"]
Q4 --> A4["EN 179 or EN 1125 document"]
Q5 --> A5["Destination market radio regime"]
Q6 --> A6["Corrosion and ingress evidence"]
Q7 --> A7["Assembly test evidence"]
A1 -.-> Risk["Furniture document stretched to cover the rest"]
| Question on the door | What is being asked | Who answers it | The document that must exist |
|---|---|---|---|
| Handle and knob furniture | Will the grip survive daily operation, and does it resist being forced | EN 1906 | Report or certificate scoped to the ordered furniture |
| Locking mechanism | Will the mechanism drive the bolt and latch under repeated operation and load | EN 14846 for an electromechanically operated lock, EN 12209 for a mechanically operated one | Certificate or report covering the electromechanical family |
| Cylinder | Does the cylinder resist picking, drilling and wear, and how is it keyed | EN 1303, or EN 15684 where the cylinder is mechatronic | Certificate covering the cylinder type and key control |
| Escape function | Can the door be released from inside without a key, in one operation | EN 179 for a lever-operated device, EN 1125 for a panic bar | Certificate for the device type named in the door schedule |
| Radio and electromagnetic compatibility | What the radio emits, and what it has to tolerate around it | The radio and electromagnetic regimes of the destination market | Declaration and marking, with the test evidence behind them |
| Environment | What rain, salt and impact do to the outside face | Ingress and impact ratings, corrosion test evidence | Test evidence matching the exposure that door has |
| Fire assembly | What happens when the door is part of a fire-rated assembly | The fire-resistance test route for assemblies | Evidence for the assembly with the hardware fitted |
For a battery-driven smart lock, the electromechanically operated lock family is the closer fit for the locking function than the mechanically operated family, and EN 14846 is written for exactly that combination of mechanical and electrical locking. Treat the routing in this table as a routing table, not a compliance finding: check the published title and scope for each designation, and confirm the route your market applies to the specific product.
Eight slots in an EN 1906 clause
A clause is not a sentence. It is a set of bindings, and each binding can be empty. When a slot is empty, the missing content is supplied by the reader's assumption, and the reader's assumption is never written down anywhere you can correct it later.
Eight slots will carry an EN 1906 clause. The order below works because each one constrains the next: you cannot name a document before you know what it must cover, and you cannot name a milestone before you know what is being asked for.
| Slot | What it binds | What fills the gap when it is empty |
|---|---|---|
| 1. Requirement | Which object, and which edition of which standard | The supplier picks the object and the document |
| 2. Object | The designation, type, finish and geometry actually quoted | The supplier ships whatever sits under the designation |
| 3. Document type | Whether a report, a certificate, a declaration or a marking is acceptable | Anything with the right letterhead satisfies the clause |
| 4. Holder | Who issued the document and who can confirm it | An unverifiable number with no scope attached |
| 5. Edition | The current published edition and any amendment in force | A document against an edition the market no longer uses |
| 6. Scope coverage | That the type entry includes the ordered variant | A certificate for a family that excludes the shipped item |
| 7. Site and validity | The production site and what keeps the evidence true after the sample passed | An assertion that the certificate simply applies |
| 8. Timing and consequence | The milestone and what follows a miss | A promise with no date and no consequence |
Slot one: the requirement, and the exclusion that travels with it
The requirement slot carries the standard, the object and the evidence type in a single sentence, and it carries the word furniture deliberately.
The lever handle and knob furniture supplied under this item shall be shown to conform with the current published edition of EN 1906 by [document type], issued by [holder], whose scope covers the product designation, furniture type, finish and geometry as quoted in this request for quotation, and shall be provided before [milestone].
That sentence works on its own. What makes it work in practice is the sentence that follows it, because the failure mode is not that a supplier lies — it is that the file is read later by somebody who has not read the clause, and who reasonably concludes that a document attached to a smart lock is about the smart lock.
The evidence supplied under this clause relates solely to the lever handle and knob furniture. It shall not be relied upon as evidence of conformity of the locking function, the cylinder, the escape function, the radio characteristics, the electrical characteristics or the environmental performance of the product, each of which is governed by a separate clause in this request for quotation.
Notice where the exclusion points. It does not say the product fails those requirements; it says this document cannot speak to them. A clause that reads like a disclaimer gets ignored, while a clause that assigns each requirement to a named place gets used. Put the exclusion in the evidence schedule as well as in the clause body, so a reviewer working through a schedule of document rows sees the boundary without reading the prose.
Slot two: the object, and why finish is the field that breaks
The object slot is where furniture clauses live or die. A furniture type entry typically lists a family of variants built on a common body, and the fields that vary across that family are the fields that can move without anybody noticing.
| Field | What to write | Where to take it from | The substitution it invites |
|---|---|---|---|
| Product designation | The factory part number exactly as it appears on the dated product page | The dated product page for the specific SKU | A near-identical designation from an adjacent series |
| Furniture type | Lever handle or knob, stated in words | The quotation line | A knob supplied against a lever line |
| Finish | The finish designation as it appears on the product page | The dated product page | The most frequent change in a furniture order |
| Handing | The handing that applies to the door swing | The door schedule and product page | Reverse-hand supplied against a swing schedule |
| Fixing centres and projection | Read from the dated product page; do not transcribe them into the request for quotation | The dated product page | Geometry that does not suit the door |
| Fixing interface | How the furniture mates with the lock case | The supplier's technical description for the SKU | A furniture set that will not mount on the case |
Two rules follow. First, do not type measured values into the request for quotation. A number written there becomes the buyer's requirement, and a mismatch reads as a dispute rather than a substitution. Keep the geometry values on the product page and put the pointer — designation, finish, dated product page reference — into the clause and the schedule instead.
Second, require the supplier to map the quotation onto the type entry, because the mapping is what is missing from almost every furniture document.
The Supplier shall state which of the furniture variants listed in the type entry of the evidence supplied correspond to the product designation, furniture type, finish and geometry quoted in this request for quotation, and shall not supply a variant outside that list without prior written notice.
In an original-equipment programme this clause earns its place on its own. The finish changes three months into production; the knob becomes a lever because the door schedule moved; the handing is wrong on one pallet because two swings were mixed in the survey. Without the notice obligation each becomes a silent substitution, and the evidence for the shipped furniture stops matching.
Slot three: the document, slot four: the holder, slot five
The document slot. Name the document type. "Evidence of EN 1906 conformity" is not a document type; it is the phrase a buyer uses when the decision has not been made, and a supplier who reads it sends whatever is easiest to send. "A certificate issued by a named body" and "the test report issued for the type, together with the signed declaration that relies on it" are document types, and a supplier can answer either.
The holder slot. Name who issued the document and who can confirm it. For a self-declaration, name the signatory and the capacity in which they sign, because the strength of a declaration comes from the legal exposure of whoever signs it. For a third-party certificate, record the issuing body so that a scope question can be put to the body rather than to a salesperson. If a supplier declines to release the certificate, do not accept the refusal silently: ask for the scope page and the holder's name, ask the holder to confirm the scope directly, and record a decision to rely on a lower rung as a decision rather than as an omission.
The edition slot. Write the current published edition, including any amendment in force at the date the evidence is issued, and require the edition and amendment cited to be stated on the document. Add a change-notification obligation so that a supersession during production does not pass unnoticed.
One practical point about furniture files. A supplier's standards pack is usually assembled over years rather than issued as one dated set, so an EN 1906 furniture document may sit beside a mechanism document from a different vintage. Never assume one PDF is internally consistent. Check the date, the edition and the scope on each document separately, and record them separately in the schedule.
Slot six: the scope, slot seven: site and validity, slot
The scope slot. The type entry must include the variant you have ordered. When it does not, you are not being asked to accept a lower quality of evidence — you are being asked to accept evidence about a different object. That is a legitimate position for a programme with a sensible risk appetite, provided the gap and its consequence are written down and someone owns them. What is not legitimate is discovering the gap at handover.
The site and validity slot. Name the production site the evidence covers, and ask what keeps the evidence true after the sample passed. Something has to maintain the connection between a tested type and a shipping product: a stated control on changes to the type, a surveillance arrangement, an inspection regime, or an internal control the supplier can evidence. Ask to see the arrangement rather than the assurance. This slot connects to the supplier-side checks in the Smart Lock Factory Audit Checklist for International Buyers and to the document review in What Documents Should You Request From a Smart Lock Supplier?.
The timing and consequence slot. Set the milestone and the consequence together, and be realistic about which evidence is available when. Furniture evidence is commonly in the supplier's file before quotation, because the handle is an existing part of the range. Mechanism evidence for a newly developed smart lock is frequently a pre-shipment condition, because the lock is the thing being developed. Two milestones on two rows, with two consequences, is the honest arrangement; a single milestone for both assumes the harder document arrives with the easier one.
CONFIRM-WITH-LOCAL-CERTIFICATION-BODY — whether a certificate issued against one edition of EN 1906 remains valid when a later edition or amendment is published, and what your national implementation guidance says at the date of your order. Ask the body that issued the document, not the factory.
The companion clause: pairing the furniture clause
The rule that makes an EN 1906 clause work is simple to state and easy to omit: every EN 1906 clause in a smart lock request for quotation is issued with a named companion clause for the locking function, and the two are cross-referenced in the schedule. One without the other leaves a hole that the furniture document will be invited to fill.
| The question on the door | The clause that answers it | What that clause must not be used for |
|---|---|---|
| Handle and knob furniture | EN 1906 | The locking function, the cylinder, the escape function, the radio |
| Electromechanically operated lock and striking plate | EN 14846 | Furniture durability, radio characteristics, fire assembly performance |
| Mechanically operated lock, latch or locking plate | EN 12209 | The electromechanical function of a battery-driven lock |
| Cylinder for locks | EN 1303 | The lock body, the electronics, the escape function |
| Mechatronic cylinder | EN 15684 | Plain mechanical cylinders, the lock body |
| Multi-point locking system | EN 15685 | Single-point smart lock bodies |
| Emergency escape device operated by a lever handle | EN 179 | Panic bars, which fall under EN 1125 |
| Emergency escape device operated by a panic bar | EN 1125 | Single-lever exit devices |
| Radio and electromagnetic compatibility | The radio and electromagnetic regimes of the destination market | Mechanical durability, escape release, ingress protection |
| Ingress and impact protection | The ingress and mechanical-impact rating system | Fire assembly performance, escape release |
| Fire and smoke door assembly performance | The fire-resistance test route for assemblies, with hardware fitted | Stand-alone hardware performance |
Every row is a routing aid, and the published title and scope for each designation is the authority. The scope boundary of the standard under discussion is set out in EN 1906 for Smart Locks: Scope, Tests and What the Standard Never Proves, and the hinge-versus-lock citation confusion that shows up in the same templates is examined in EN 1906 Versus EN 1935: Which One Applies to Your Smart Lock Door.
The class and grade numbering that appears on furniture documents is decoded in Decoding EN 1906 Class and Grade Numbers for Door Hardware. For drafting purposes the rule is simple: do not transcribe a number from a document into the clause. Write the requirement against the current published edition, let the supplier state the classification on the evidence, and check that it agrees with the variant you ordered.
classDiagram
class ClauseSet {
+string reference
+string requirement
+string boundary
+string boundTo
}
class FurnitureClause {
+string designation
+string furnitureType
+string finish
+string geometry
+string documentType
+string productionSite
}
class MechanismClause {
+string designation
+string drivingFunction
+string documentType
}
class ScheduleRow {
+string documentType
+string holder
+string number
+string issueDate
+string coveredVariant
+string dueMilestone
+string consequence
}
ClauseSet "1" *-- "1" FurnitureClause : furniture requirement
ClauseSet "1" *-- "1" MechanismClause : locking function requirement
FurnitureClause --> ScheduleRow : evidenced by
MechanismClause --> ScheduleRow : evidenced by
Who supplies the furniture decides whose file it goes
Before the clause is drafted, one commercial fact has to be settled, because it determines whose document is being requested and from whom: who actually supplies the handle. Three arrangements are common, and they produce three different document flows.
| Arrangement | Where the furniture evidence sits | What the smart lock request for quotation must say |
|---|---|---|
| Lock and furniture supplied as one package by the lock supplier | In the lock supplier's pack, with the furniture clause and the mechanism clause in the same file | Require both documents, and require the type entry to name the furniture as well as the lock |
| Lock supplied with a specified furniture set from the lock supplier's range, chosen on the quotation | Same pack, but the variant selection belongs to the buyer | Require the supplier to map the quoted finish and geometry onto the type entry |
| Furniture supplied under a separate contract line by a hardware supplier | In the hardware supplier's file, under a different contract, with a different holder and expiry date | Ask for no furniture evidence on the lock contract, and require the two contracts to name each other so the boundary is visible |
The third arrangement is the one that quietly breaks. The smart lock file closes with a document that the lock supplier's evidence cannot supply, the hardware file closes with a document nobody asked for, and the door arrives complete while the file stays incomplete. A single sentence in the schedule — naming which party supplies the furniture and which contract line carries the evidence — prevents it, and matters more still where the two files are read by people who have never met.
The four documents a supplier will offer
Four documents arrive under a heading like "EN 1906 compliance", and they are not interchangeable. Naming which one the clause requires is the difference between a comparable set of quotations and a folder of brochures.
| Document | What it actually says | What to check before relying on it | Typical furniture failure |
|---|---|---|---|
| Test report | A sample of a described product was tested against named clauses | Number, date, who tested, the sample description, the clauses tested, whether the sample matches the ordered variant | A report on a handle in a different finish, or on a knob rather than the quoted lever |
| Certificate | A named body attests that a defined scope of product conforms to a defined standard | Issuing body, number, scope wording, standards listed, issue date, any surveillance or validity condition | A scope covering a furniture family whose type entry omits the ordered variant |
| Declaration of conformity | The manufacturer or importer makes its own legal claim | Who signed it, in what capacity, what it covers, what evidence it rests on, whether it matches the shipped variant | Signed by a party with no relationship to the product, or with no signature and no date |
| Marking | The manufacturer declares the product is placed on the market under an applicable regime | Which regime, whether the marking appears on the product or only in a document, and what the supporting declaration says | A marking shown in a brochure graphic rather than on the product or its label |
The rungs run in a known order: a marketing image at the bottom, then a self-declared declaration, then a test report on a sample, then a third-party certificate with a scope and a number, then a certificate whose scope covers the exact variant being bought, and finally the production-control evidence that keeps it valid after the sample passed. The recurring commercial failure is buying near the bottom and discovering at installation that nothing above it was going to exist. For en 1906 smart lock rfq clause, the position on this ladder is what the purchase decision turns on.
So set the rung in writing before the request for quotation is issued: "Responses are evaluated at the evidence rung stated in the evidence schedule, and a lower rung may not be substituted for the rung stated." That turns an argument about how much evidence is enough into a decision you made in advance and can defend.
Marking, the construction products route and the market question
Two routes run in parallel with the furniture requirement, and neither substitutes for it.
The first is market access. A marking on the product declares that the product is placed on the market under an applicable regime; it says nothing about which clauses of which standard were tested on which sample, and nothing about furniture performance. Which regimes apply, and which mark each destination market expects, is a per-market and per-product question. Acceptance practice for the UK mark varies between specifiers and approving bodies, which is a recurring source of confusion.
The second is the construction products route. For door hardware sold as a construction product, the European construction products route drives a Declaration of Performance in addition to a declaration of conformity, and the mechanically operated and electromechanically operated lock families sit inside that route. Whether the handle and knob furniture in your order sits on that route is a per-product question your market's implementation decides, and it should be checked rather than assumed. The routing table for that route and the declaration language is in Writing the EU Construction Products Regulation Into a Smart Lock RFQ: Clause Language that Gets Real Answers.
CONFIRM-WITH-LOCAL-LEGAL-ADVISER — which conformity route applies to the furniture and to the locking mechanism in each market you are supplying, whether a Declaration of Performance is required in addition to a declaration of conformity, and which party in your supply chain carries the legal obligation to hold and to produce it. Check the published scope and the harmonised list in force for each market at the date of your order, because the list changes.
CONFIRM-WITH-LOCAL-REGULATORY-CONSULTANT — whether the marking on the product and the evidence supplied under the furniture and mechanism clauses are consistent, and whether the mark required differs from the mark already present for each destination market.
Keep the two routes apart on paper. A short clause stating that conformity evidence under the furniture clause is supplied in addition to any marking or market-access document, and that neither substitutes for the other, costs one line and prevents a category of handover argument.
The evidence schedule row for the furniture clause
The schedule is where clauses become checkable. One row per clause, and a row with an empty cell is a clause nobody is working on.
| Column | What goes in it | Why it earns its place |
|---|---|---|
| Clause reference | The clause number from the request for quotation | Ties the document to the obligation that demanded it |
| Document type | Report, certificate, declaration or marking | Stops a lower rung being passed off as the required one |
| Object covered | Designation, furniture type, finish and geometry as quoted | The column that catches a substitution later |
| Holder | The issuing body, or the signatory and capacity | Gives you somebody to ask when the scope is unclear |
| Number and date | As printed on the document | Dates the evidence and exposes mixed-vintage packs |
| Edition cited | As printed, with any amendment | Connects the document to the edition in force |
| Production site | The site the evidence covers | Catches the second-factory problem |
| Due milestone | Before quotation, before award or before shipment | Decides whether you are comparing documents or promises |
| Consequence | What follows a miss | A date without a consequence is a date nobody has to meet |
The worked row for a typical furniture clause carries the clause reference, the document type, the quoted designation with its finish and geometry, the issuing body, the number and date as printed, the edition cited, the production site that will ship the goods, a milestone before the technical comparison closes, and a consequence.
Two schedule disciplines are worth more than the individual columns. Split the pack — ask for one file per object rather than one combined standards pack, so the furniture document, the mechanism document and the marking are never mistaken for each other. And record the rung you are buying at, because a schedule with no rung statement invites a negotiation down one clause at a time.
Reading the responses: what comes back and what it means
Suppliers reply in paragraphs. Grade the answer rather than the tone, and return the replies that are not answers while there is still time to re-ask.
| Reply pattern | Reading | Action |
|---|---|---|
| Document named, attached, with a scope page | Answerable | Grade against the rung the schedule states |
| A standard listed with no document attached | Not yet an answer | Request the document and name the type required |
| A scope page listing a furniture family that excludes the quoted finish or geometry | Wrong object for this order | Re-ask with the quotation line fields written into the request |
| An edition cited with no amendment | Ambiguous | Ask for both, and for the amendment in force |
| The claim that the company is "certified to EN 1906" with no number, no scope and no holder | An unattributed assertion | Ask for the holder and the scope, in writing |
| The claim that the certificate is available on request after the order | A promise, not a document | Decide whether it is a condition of award or of shipment, and write the date and consequence |
| One combined file holding the furniture, mechanism and marking documents | One pack, three objects | Ask for it split, one file per object, before evaluation |
The last row causes the mistake this article is about. When the furniture certificate, the mechanism certificate and a market-access declaration travel together in one pack, a reader under time pressure will find the EN 1906 document first, read the pack as a set of answers for the product, and treat the product as evidenced. Splitting the pack is a five-minute instruction that prevents the costliest misreading in the file.
The clause set, collected
Collected, these are the clauses a smart lock request for quotation would carry for the furniture requirement. The bracketed fields are the ones only the programme can fill in.
| Ref | Clause | Document that must exist | Bound to |
|---|---|---|---|
| C1 | Furniture shown to conform with the current published edition of EN 1906 by [document type], scope covering the quoted designation, type, finish and geometry | Certificate or test report with a scope page | Supplier |
| C2 | Evidence under C1 relates solely to the furniture and is not evidence of the locking function, cylinder, escape function, radio, electrical or environmental performance | Boundary statement | Buyer |
| C3 | Supplier states which type entry variants correspond to the quoted designation, type, finish and geometry, and gives prior notice of any variant outside that list | Type entry mapping | Supplier |
| C4 | Evidence supplied as a complete document with its scope page, not a summary, extract or marketing page | Full document | Supplier |
| C5 | Conformity to the current published edition and any amendment in force at issue, cited on the document | Edition statement | Supplier |
| C6 | Supplier notifies before shipment if the cited edition or amendment is superseded and states whether the evidence remains valid | Change notification | Supplier |
| C7 | Evidence covers the production site that will ship the goods, with the production-control and type-change arrangement stated | Site statement and control description | Supplier |
| C8 | Responses identify document type, holder, number, date, edition cited, object covered and production site, and attach the document | Complete response per clause | Each respondent |
| C9 | Documents supplied as one file per object, so furniture, mechanism and marking evidence are not held in one combined pack | Split packs | Supplier |
| C10 | The locking mechanism, cylinder, escape function, radio and environment are specified in separate clauses and evidenced separately | Companion clause set | Supplier |
The two fields carrying the most weight are the milestone in C1 and the boundary in C2. The milestone decides whether you are comparing documents or comparing intentions, and it is much cheaper to set before the quotations arrive. The boundary decides whether the file stays honest, and it costs one sentence.
Ten moves before the request for quotation goes
- Break the door into its questions. Furniture, mechanism, cylinder, escape, radio, environment, assembly. If you cannot list them, you cannot write clauses for them.
- Decide who supplies the furniture. Lock package, supplier's furniture set, or a separate hardware contract. This decides whose document you request.
- Partition the requirement by object. One clause set for the furniture, a separate clause set for the locking function, separate clauses for everything else.
- Fill the object fields from the dated product page. Designation, furniture type, finish, handing and geometry — and keep the measured values off the clause text.
- Name the document type. Not "evidence", not "compliance". A report, a certificate, a declaration or a marking.
- Write the boundary sentence and put it in the schedule. It is the clause that stops the furniture document being borrowed.
- Decide the rung and write it into the schedule. You are choosing where the programme sits on the ladder of evidence, before quotations arrive.
- Set two milestones, not one. Furniture evidence before the technical comparison closes; mechanism evidence as a condition of award or of shipment, each with its own consequence.
- Check the neighbours. Mechanism, cylinder, escape, radio, environment and fire assembly are separate questions with separate documents, and each one needs its own clause or an explicit statement that it is out of scope for this contract.
What a reviewer will ask about the handle
"The supplier says the lock already has EN 1906. Why are you asking for more?" Because a document that names EN 1906 says something about the furniture, and your question is about the ordered variant of that furniture. Ask for the scope page and the type entry, and the answer is usually already inside the document the supplier offered.
"Can we just take the certificate number and check it ourselves?" You can, and you should, but a number carries no scope. The scope page tells you what is covered; the number tells you who to ask. Ask for the document.
"Our supplier will not release the certificate for commercial reasons." Then ask for the scope page, the holder and the date, and ask the holder to confirm the scope directly. If the answer is still no, the programme is choosing to rely on a lower rung, and that choice belongs in the minutes rather than in a silence.
"Should we name the edition, or leave it open?" Name the current published edition including any amendment in force at the date of issue, require the edition and amendment to be cited on the document, and attach a change-notification obligation. If a specific edition is wanted for a reason — a local implementation rule, a tender instruction, a client standard — put that reason in the clause so it survives the next review.
Where this clause set stops
The clause set cannot tell you which standard your market applies to the furniture, because that is a per-product and per-market question and it changes. It cannot tell you whether a given door needs an escape device, because that is a question about the door schedule, the escape strategy of the building and the local approving route. It does not tell you how much evidence is enough — that is a programme risk decision, and the value of the rung statement is that it lets you make the decision explicitly.
What the clause set does do is narrow the claim. It makes the furniture requirement say exactly what it covers, keep it out of the questions it cannot answer, and put the locking function, the cylinder, the escape function, the radio and the environment into clauses of their own with evidence of their own. The evidence-list version of the same set for a tender pack is in EN 1906 in a Smart Lock Tender Pack: the Evidence Checklist, and the ways this evidence disappoints buyers after award are set out in Three Ways EN 1906 Evidence Disappoints Smart Lock Buyers.
For the sourcing-side preparation around these moves, the Smart Lock Supplier Due Diligence Checklist and the Smart Lock RFQ Guide for International Buyers are the documents to hand to whoever maintains the template. The Smart Lock Door Measurement Guide and Smart Lock Handle Measurement supply the geometry fields the object slot depends on. The order samples page describes the product-side review, the certifications page the conformity documentation route, and request a quote the route where a scoped enquiry saves a round of correspondence.

