Slk 238 door fit notes: assess SLK-238 door fit with a measurement-led runbook covering mortise geometry, panel clearance, supplier drawings, samples,.

Publicerad den: maj 16, 2024

Will SLK-238 Fit Your Door? A Fit and Preparation Guide

Will SLK-238 Fit Your Door? A Fit and Preparation Guide

Use these slk 238 door fit notes to turn a broad question—“Will it fit?”—into a controlled procurement decision. The short answer is that the current catalogue record does not support a universal yes or no. It identifies the lock’s panel and mortise family, but its Door fit field is blank. Confirm on the dated product page for the specific SKU, and obtain the applicable dimension drawings before approving a purchase order.

Direct answer. Condensed to the essential point, slk 238 door fit notes turns a request into a decision record. slk 238 door fit notes and slk-238 are the two parts of slk 238 door fit notes most often skipped. A slk 238 door fit notes describes how one component behaves under load. The datasheet makes claims. slk 238 door fit notes is what slk 238 door fit notes can be tested against.

The phrase slk 238 door fit notes is anchored in slk 238 door fit notes. For the rest of this article it denotes the conditions and evidence that slk 238 door fit notes sets out below. Nothing wider than that.

  • Check the capability — confirm on the dated product page for the specific SKU behind slk 238 door fit notes
  • Check the limit — record where the technology in slk-238 stops working
  • Check the fallback — name the mechanical path that remains if slk 238 door fit notes fails
  • For slk 238 door fit notes, the order below is fixed and slk 238 is the reference point.

A photograph, nominal door size, or installer’s phrase such as “standard hotel door” is not enough to establish fit. The evidence must connect the exact door leaf and frame to the current SKU drawing, then cover the hardware and operating interfaces that surround the lock.

This runbook produces one of four procurement outcomes: confirmed fit, conditional fit, hold, or out of scope. It also defines who owns each measurement, which evidence is required, and what must happen when a door differs from the schedule. The goal is to prevent a later door-preparation change from becoming an undocumented lock-order change.

Define the release outcome before measuring

SLK-238 door fit should be treated as a documented relationship between a particular door and a particular lock revision. The relationship is not established by the product name, the category, or one dimension.

OutcomeMinimum evidenceProcurement meaning
Confirmed fitCurrent SKU drawing, completed field measurements, and an accepted trial fitFit approval can be released for ordering
Conditional fitDrawing and measurements pass, but a sample or final site check remains openPurchase may be held until the named condition is closed
HoldA drawing, measurement, or interface check is missing or contradictoryNo fit-based approval should be issued
Out of scopeThe door or operating requirement falls outside the documented, current configurationReview an alternative door or lock rather than forcing the installation

A panel dimension answers only one part of the question. It does not establish the mortise cutout, backset, spindle clearance, frame rebate, door handing, projection beyond the face, or room for adjacent hardware. Procurement should therefore approve the evidence package, not a label called “fits.”

Assign one owner to every fit decision

The procurement manager controls the commercial release, but should not be asked to infer geometry from an installer’s verbal assurance. Assign named owners and require the evidence listed below.

RoleFit responsibilityRequired evidence
Procurement managerHolds the order and resolves missing supplier informationApproved drawing revision, measurement sheet, exception log, and final fit decision
Site surveyorRecords actual door and frame dimensionsAnnotated drawings, photographs with a visible scale, and door-by-door schedule
Door installer or fabricatorChecks the preparation against the approved drawingMarked cutout template and signed trial-fit record
Supplier technical contactDefines the current SKU geometry and answers deviationsDated drawings, installation instructions, and written response to exceptions
Project operations or security leadConfirms access workflow and adjacent-hardware constraintsApproved operating sequence and interface checklist

Use a controlled file name for each door record, such as the project, room or door identifier, measurement date, drawing revision, and sample status. Keep measurements, photographs, and decisions together. A single spreadsheet marked “standard” loses the evidence needed when one leaf warps, a closer is relocated, or a replacement door arrives from another supplier.

No owner should approve their own unresolved exception. The person who closes the evidence should be different from the person requesting an exception where practical.

Run the seven gates in sequence

The gates prevent early assumptions from becoming a purchase-order change. Do not jump from a catalogue image to the release stage merely because the project schedule is tight.

flowchart TD
    A[Freeze door requirement] --> B[Build door schedule]
    B --> C[Measure leaf and frame]
    C --> D[Match current SKU drawing]
    D --> E{Geometry and clearance pass?}
    E -->|Yes| F[Trial fit and inspect]
    E -->|No| G[Hold and raise exception]
    G --> C
    F --> H{Record accepted?}
    H -->|Yes| I[Release fit approval]
    H -->|No| G
GateInputRequired outputHard stop
0Project and access requirementControlled door requestNo supplier question has yet been framed
1Room and door inventoryDoor-by-door scheduleUnknown doors are marked for measurement
2Physical site accessCompleted measurement sheetMissing dimensions remain open
3Current SKU documentsDrawing-to-door comparisonUnverified revisions or generic templates are rejected
4Approved preparationTrial-fit recordVisual inspection alone is insufficient
5Trial-fit evidenceInterface and exception logUnresolved clashes block release
6Closed evidence packageProcurement fit decisionAll named approvers have signed

Record a hold as a controlled status, not as an informal email. Give every exception an owner, a requested response date, and a linked drawing or photograph. This matters even for a single-door trial because the same correction can affect a group of rooms.

Build the door schedule before the bill of materials

Hotel lock door preparation starts with a schedule that treats every leaf as an installation condition. Do not average the measurements across a floor or use the door schedule supplied by an architect as a substitute for site verification.

The Office Smart Lock Site Survey provides a useful reference for recording workplace access points and surrounding hardware. For existing guestroom doors, the Smart Lock Retrofit Site Survey is the closer starting point because retrofit conditions must be observed rather than inferred.

Capture the following fields for each door:

Schedule fieldWhat to record
Door identityProject, building, floor, room or door identifier, and schedule revision
Leaf constructionMaterial, core type, thickness range, and visible condition
Nominal and measured sizeLeaf width, height, thickness, and rebate dimensions
OrientationSwing direction, handing, active edge, and frame side
Existing preparationMortise, faceplate, cylinder, spindle, follower, strike, and keeper
Frame conditionFrame type, stop position, rebate, reveal, fixing points, and movement
Adjacent hardwareDoor closer, hold-open device, escape hardware, reader, and existing access controls
Evidence referenceDrawing number, photograph set, measurement sheet, and sample record
Current statusUnmeasured, measured, queried, trial-fitted, confirmed, or held

Mark a door “not measured” rather than “standard.” If a future door replaces the surveyed leaf, the replacement enters the same measurement and release sequence. This prevents a fit approval from being transferred automatically to a visually similar door.

Turn the slk 238 door fit notes into a measurement record

A repeatable door thickness measurement is more useful than one nominal figure. Use a rigid steel rule or a verified measuring tool and record actual dimensions with units. Measure the leaf at several positions because timber, metal, composite, and previously modified doors can vary.

The table below is a field worksheet, not an SLK-238 compatibility list. The current supplier drawing defines which values and variations are acceptable.

MeasurementMethodRecord
Leaf thicknessMeasure at the hinge, lock edge, and mid-span near the lock preparationThree readings, minimum, maximum, and instrument used
Leaf width and heightMeasure at top, middle, and bottom; include the finished surfaceActual dimensions rather than nominal sizes
RebateMeasure depth, width, length, and position of the frame stopFull-size profile and any existing seal
Lock-edge setbackMeasure from the active door edge to the centreline of the mortise or spindleDimension and a marked photograph
Stile widthMeasure usable face area beside the lock zoneMinimum available width and any obstruction
Frame depthMeasure from the door face to the rebate or stopFull projection plus clearance
Handing and swingPhotograph the pull side and mark hinge, lock, and active edgesDirection, handing, and any floor restriction

Photograph each dimension in context. A close-up should include the measuring tool and the edge from which the dimension is taken. Annotate the same photographs with the door identifier; loose image files quickly become unusable evidence.

Record any bevel, taper, bowed panel, uneven frame, or surface damage separately. Do not average these conditions into a passing number. Supplier acceptance criteria and permitted measurement methods must be confirmed on the dated product page for the specific SKU and in the current drawing pack.

Match the No. 2 hotel mortise to real door geometry

The catalogue record identifies the mortise as a No. 2 hotel mortise. That is a useful starting description, but the name alone does not prove compatibility with a particular door. The family label does not replace a cutout drawing, and an existing mortise should not be accepted merely because it looks similar.

Confirm on the dated product page for the specific SKU before using catalogue information in a purchase decision. The detailed catalogue treatment is also separated from fit in Data Memo: What the SLK-238 Data Sheet Actually Tells a Buyer.

InterfaceField checkEvidence needed for acceptance
Mortise caseMeasure case depth, width, height, fixing positions, and pocket clearanceCurrent SKU cutout drawing
FaceplateRecord length, width, screw centres, and active-edge setbackFaceplate drawing and marked door template
Backset and spindleMeasure the spindle centreline from the active edge; record spindle diameter, projection, and follower sizeDated dimensional drawing
Latch or boltObserve the required projection, throw, and relationship to the keeperAssembly drawing and strike detail
Cylinder and overrideRecord opening, projection, and required internal clearanceInstallation guide for the exact configuration
Strike and keeperMeasure frame positions, recess, fixing points, and keeper engagementFrame and strike drawings

For a retrofit, remove only what the approved procedure permits and preserve enough evidence to determine whether the existing preparation can be reused. If the door contains an unfamiliar mortise, measure it rather than adapting it informally. A revised spindle, faceplate, or keeper may affect the door structure and adjacent components.

The correct outcome is not necessarily reuse. It may be retain, modify, replace the mortise area, or select another door preparation. The decision must follow the current SKU evidence and the project’s approved construction plan.

Prove the panel envelope, not merely the lock body

The catalogue record for SLK-238 lists the panel dimensions as 301 × 73 × 24 mm. It also identifies the material as aluminum alloy and records Black, Silver, and Red antique bronze finishes. These are catalogue fields, not a complete installation envelope. Confirm on the dated product page for the specific SKU before using the dimensions for procurement or preparation.

Use the supplier drawing to check all of the following:

  • The panel fits within the available stile and rebate without cutting into an engineered edge.
  • The required fixing points have material behind them and do not conflict with the mortise.
  • Projection beyond the door face leaves clearance for the frame, seal, closer, handle, and room-side traffic.
  • The panel can be installed and serviced without removing adjacent hardware that must remain in service.
  • Handing, handle position, reader orientation, and indicator visibility suit the door.
  • Surface finish and edge conditions do not create a visible gap or an unusable rebate.
  • The strike and keeper positions align without forcing the panel or frame.

The supplied SLK-238 dimensions should be checked against the complete drawing rather than marked “pass” on their own. A panel can be narrow enough while the spindle, cylinder, wiring route, or fixing pattern still fails. Keep the projected silhouette and every required clearance visible on the marked-up drawing.

Do not drill the production door until the preparation has been approved against the current drawing. If a visual template is used for a trial, mark it as a template and record which dimensions it represents.

Check operating interfaces around the prepared door

Mechanical fit is only one part of RFID hotel lock installation. The catalogue lists RFID/IC card access, mechanical override, hotel lock management software, a standalone lock, and a PC-linked card encoder with no in-room network required. It also lists guest card issuance, floor and room permissions, check-in validity windows, and unlock records. Confirm on the dated product page for the specific SKU because the operating configuration forms part of the released product definition.

The prepared door must support the intended operating sequence:

  1. Confirm that the card reader remains reachable in normal use and is not obstructed by a handle, privacy fitting, or stored furniture.
  2. Confirm that emergency access can be reached without adding hardware outside the documented configuration.
  3. Confirm that the battery compartment can be serviced without damaging the door finish or adjacent frame.
  4. Confirm that a door closer, hold-open device, reader, or other control can operate at the same time as the lock.
  5. Confirm that the room workflow supports the intended card issuance, validity window, override, and record review process.

The record states a supply of 4 × AA alkaline batteries and a standard low-battery alert. Confirm on the dated product page for the specific SKU, and use that evidence when deciding whether service access and stock procedures are adequate.

Door preparation must also respect any project-specific fire-door, egress, accessibility, and access-control constraints.

CONFIRM-WITH-LOCAL-AUTHORITY: Confirm fire-door, egress, accessibility, and access-control requirements with the authority and project professionals for the installation location.

For the credential and software side of the project, use the Regulatory Brief: SLK-238 Credential and Software Configuration Options to keep card issuance, permissions, validity periods, and records in one review cycle.

Accept the drawing pack as controlled evidence

The catalogue states that dimension drawings, an installation guide, and a full datasheet are available on request. Confirm on the dated product page for the specific SKU, then request the documents that apply to the quoted configuration. A collection of photographs sent at different times is not a controlled drawing pack.

DocumentAcceptance questionOwner
Dimension drawingDoes it identify the current SKU or configuration and show every preparation dimension?Supplier technical contact
Installation guideAre sequence, tool, fixing, and service-access requirements stated?Installer and supplier
Mortise and faceplate detailCan the field measurements be compared directly with the cutout?Supplier technical contact
Panel and clearance drawingAre projection, fixing zones, and adjacent clearances defined?Supplier and installer
Sample procedureWhat is checked, who records it, and what constitutes acceptance?Installer and project representative
Revision recordCan the drawing used for approval be identified unambiguously?Procurement manager
Change noticeHow will a drawing or product revision affect an open order?Procurement manager

Mark the approved revision on every measurement sheet and sample record. When a newer document arrives, compare it with the previous revision before replacing it. Record whether the change affects preparation, operation, packaging, or only documentation. A revised catalogue photograph without a revised dimensional drawing does not close an old exception.

Compare common door scenarios before committing

The following decision-comparison table helps procurement distinguish a documented match from an assumption. It does not predict the result before measurement; it defines what each result requires.

Door conditionEvidence availableFit classificationRequired action
New leaf matching the current drawingSupplier drawing and field measurements agreeConfirmed on geometryComplete trial fit and release if the sample is accepted
Existing leaf with a reusable mortiseExisting preparation is measured and matches the drawingConditional until trial fitVerify spindle, faceplate, keeper, and panel clearance
Existing mortise only looks similarNo current drawing for the existing caseUnresolvedHold and request the cutout dimensions
Door is thinner, wider, or more deeply rebated than the drawing allowsMeasurements fall outside the documented envelopeOutside the recorded fitReview preparation changes or another lock option
Door schedule changes after approvalNew revision replaces the measured leafApproval withdrawnReopen measurement, drawing, and trial-fit gates
No field measurement existsOnly a nominal size is availableUnknownSchedule a site survey before commercial release
Hardware crowds the lock zoneCloser, reader, trim, or escape device conflicts with the preparationInterface exceptionRecord the clash and obtain an approved resolution

This matrix should sit beside the door schedule, not replace it. A “confirmed” result belongs to a named door and drawing revision. It cannot be generalized to another leaf with the same nominal size, especially where the frame, handing, surface, or adjacent hardware differs.

When the fit record remains conditional, state the exact condition that must close it. “Check on site” is not a release condition. A useful condition names the measurement, drawing clause, sample step, responsible person, and evidence required.

Control the sample and route exceptions

Use the first installation or a representative sample to test the approved preparation, then document what was checked. The sample is a verification step, not a reason to improvise. If the door does not match the approved drawing, stop and record the discrepancy rather than enlarging, narrowing, or relocating a cutout without approval.

ExceptionImmediate containmentEvidence to close it
Panel or fixing zone conflicts with the door edgeMark the affected area and do not drillRevised drawing or written preparation change
Spindle or follower clearance is insufficientKeep the current bore untouchedSupplier confirmation of the correct preparation
Faceplate or strike position is misalignedMark both door and frame positionsMarked drawing and revised frame check
Door closer or handle clashes with the panelRemove only temporary obstructionsInterface approval and adjusted drawing or hardware layout
Handing is reversed or ambiguousSuspend fitting and label the doorCorrect handing record and rechecked measurement
Frame, leaf, or surface condition differs from the surveyPhotograph and reassess the affected doorUpdated measurement and revised fit decision

Keep an exception log with the issue, affected doors, evidence, owner, and status. Decide whether the exception affects one door, a door type, a floor, or the project. If it changes the preparation for multiple doors, update the schedule and drawing package before work continues.

Record the trial-fit result by component: panel position, fixing access, spindle operation, latch or bolt engagement, strike alignment, handle movement, reader access, and service access. Do not reduce the result to “installed successfully.” A successful installation can still reveal an operating clash or an undocumented preparation change.

Release the fit package to procurement

The final fit package should contain the door schedule, measurement sheets, photographs, the current supplier drawing and installation guide, the marked template, the trial-fit record, the interface checklist, the exception log, and signed approvals. A single “fit confirmed” message is not enough to reconstruct the decision later.

ApproverMust confirmSignature meaning
Site surveyorMeasurements match the photographs and door identifiersField evidence is complete
Installer or fabricatorPreparation and trial fit follow the approved drawingPhysical work is traceable to the drawing
Supplier technical contactAny deviation has an approved written answerTechnical exceptions are closed
Project operations or security leadAccess and adjacent-hardware workflow is workableOperational constraints are accepted
Procurement managerThe package identifies the exact revision and released doorsFit approval is granted for named doors

Use the Checklist Tearoff: SLK-238 Purchase-Order Checklist: What to Confirm Before Ordering after the fit package is complete. Fit approval should be one controlled input to that checklist, not a substitute for the other commercial and configuration checks.

Do not treat confirmed fit as approval of the purchase order. A drawing revision, product configuration, delivery batch, packaging instruction, or order quantity may still require separate confirmation. If a released door is replaced after order placement, return that door to the fit gates before installation.

Send one preparation-ready request to the supplier

A focused request reduces clarification cycles and gives the supplier enough information to return a usable answer. Include the exact SLK-238 configuration being considered, but do not ask for a general compatibility statement that cannot be tied to a drawing.

The same question is worked through in more detail in the smart lock environmental specification. That is the same question slk 238 door fit notes has to answer here.Prepare the request with these fields:

  • Project, supplier, requester, date, and required response date
  • Door identifier and a marked leaf-and-frame drawing
  • Measured leaf dimensions, rebate, backset, spindle, and existing mortise details
  • Existing faceplate, strike, keeper, closer, and other adjacent hardware
  • Photographs with scales and a reference to each measurement sheet
  • Requested confirmation of current SKU drawings, cutout dimensions, panel envelope, and tolerances
  • Requested installation, trial-fit, and change-notification procedure
  • Required document language, revision format, and approval route

Ask the supplier to answer each deviation separately. A response such as “should work” is not a dimensioned acceptance. Require a marked drawing or written instruction that identifies the affected door and revision.

The commercially useful output from this runbook is not another catalogue image. It is a traceable fit decision that protects preparation effort, gives site teams one approved basis for work, and lets procurement order against known evidence. Send the completed package with a request for a quote when the drawing revision, configuration, and preparation details are ready for commercial review.

Din kundvagn
Din upplevelse på denna webbplats förbättras om du tillåter cookies. Cookiepolicy
Chat on WhatsApp