Will SLK-238 Fit Your Door? A Fit and Preparation Guide
Use these slk 238 door fit notes to turn a broad question—“Will it fit?”—into a controlled procurement decision. The short answer is that the current catalogue record does not support a universal yes or no. It identifies the lock’s panel and mortise family, but its Door fit field is blank. Confirm on the dated product page for the specific SKU, and obtain the applicable dimension drawings before approving a purchase order.
Direct answer. Condensed to the essential point, slk 238 door fit notes turns a request into a decision record. slk 238 door fit notes and slk-238 are the two parts of slk 238 door fit notes most often skipped. A slk 238 door fit notes describes how one component behaves under load. The datasheet makes claims. slk 238 door fit notes is what slk 238 door fit notes can be tested against.
The phrase slk 238 door fit notes is anchored in slk 238 door fit notes. For the rest of this article it denotes the conditions and evidence that slk 238 door fit notes sets out below. Nothing wider than that.
- Check the capability — confirm on the dated product page for the specific SKU behind slk 238 door fit notes
- Check the limit — record where the technology in slk-238 stops working
- Check the fallback — name the mechanical path that remains if slk 238 door fit notes fails
- For slk 238 door fit notes, the order below is fixed and slk 238 is the reference point.
A photograph, nominal door size, or installer’s phrase such as “standard hotel door” is not enough to establish fit. The evidence must connect the exact door leaf and frame to the current SKU drawing, then cover the hardware and operating interfaces that surround the lock.
This runbook produces one of four procurement outcomes: confirmed fit, conditional fit, hold, or out of scope. It also defines who owns each measurement, which evidence is required, and what must happen when a door differs from the schedule. The goal is to prevent a later door-preparation change from becoming an undocumented lock-order change.
Define the release outcome before measuring
SLK-238 door fit should be treated as a documented relationship between a particular door and a particular lock revision. The relationship is not established by the product name, the category, or one dimension.
| Outcome | Minimum evidence | Procurement meaning |
|---|---|---|
| Confirmed fit | Current SKU drawing, completed field measurements, and an accepted trial fit | Fit approval can be released for ordering |
| Conditional fit | Drawing and measurements pass, but a sample or final site check remains open | Purchase may be held until the named condition is closed |
| Hold | A drawing, measurement, or interface check is missing or contradictory | No fit-based approval should be issued |
| Out of scope | The door or operating requirement falls outside the documented, current configuration | Review an alternative door or lock rather than forcing the installation |
A panel dimension answers only one part of the question. It does not establish the mortise cutout, backset, spindle clearance, frame rebate, door handing, projection beyond the face, or room for adjacent hardware. Procurement should therefore approve the evidence package, not a label called “fits.”
Assign one owner to every fit decision
The procurement manager controls the commercial release, but should not be asked to infer geometry from an installer’s verbal assurance. Assign named owners and require the evidence listed below.
| Role | Fit responsibility | Required evidence |
|---|---|---|
| Procurement manager | Holds the order and resolves missing supplier information | Approved drawing revision, measurement sheet, exception log, and final fit decision |
| Site surveyor | Records actual door and frame dimensions | Annotated drawings, photographs with a visible scale, and door-by-door schedule |
| Door installer or fabricator | Checks the preparation against the approved drawing | Marked cutout template and signed trial-fit record |
| Supplier technical contact | Defines the current SKU geometry and answers deviations | Dated drawings, installation instructions, and written response to exceptions |
| Project operations or security lead | Confirms access workflow and adjacent-hardware constraints | Approved operating sequence and interface checklist |
Use a controlled file name for each door record, such as the project, room or door identifier, measurement date, drawing revision, and sample status. Keep measurements, photographs, and decisions together. A single spreadsheet marked “standard” loses the evidence needed when one leaf warps, a closer is relocated, or a replacement door arrives from another supplier.
No owner should approve their own unresolved exception. The person who closes the evidence should be different from the person requesting an exception where practical.
Run the seven gates in sequence
The gates prevent early assumptions from becoming a purchase-order change. Do not jump from a catalogue image to the release stage merely because the project schedule is tight.
flowchart TD
A[Freeze door requirement] --> B[Build door schedule]
B --> C[Measure leaf and frame]
C --> D[Match current SKU drawing]
D --> E{Geometry and clearance pass?}
E -->|Yes| F[Trial fit and inspect]
E -->|No| G[Hold and raise exception]
G --> C
F --> H{Record accepted?}
H -->|Yes| I[Release fit approval]
H -->|No| G
| Gate | Input | Required output | Hard stop |
|---|---|---|---|
| 0 | Project and access requirement | Controlled door request | No supplier question has yet been framed |
| 1 | Room and door inventory | Door-by-door schedule | Unknown doors are marked for measurement |
| 2 | Physical site access | Completed measurement sheet | Missing dimensions remain open |
| 3 | Current SKU documents | Drawing-to-door comparison | Unverified revisions or generic templates are rejected |
| 4 | Approved preparation | Trial-fit record | Visual inspection alone is insufficient |
| 5 | Trial-fit evidence | Interface and exception log | Unresolved clashes block release |
| 6 | Closed evidence package | Procurement fit decision | All named approvers have signed |
Record a hold as a controlled status, not as an informal email. Give every exception an owner, a requested response date, and a linked drawing or photograph. This matters even for a single-door trial because the same correction can affect a group of rooms.
Build the door schedule before the bill of materials
Hotel lock door preparation starts with a schedule that treats every leaf as an installation condition. Do not average the measurements across a floor or use the door schedule supplied by an architect as a substitute for site verification.
The Office Smart Lock Site Survey provides a useful reference for recording workplace access points and surrounding hardware. For existing guestroom doors, the Smart Lock Retrofit Site Survey is the closer starting point because retrofit conditions must be observed rather than inferred.
Capture the following fields for each door:
| Schedule field | What to record |
|---|---|
| Door identity | Project, building, floor, room or door identifier, and schedule revision |
| Leaf construction | Material, core type, thickness range, and visible condition |
| Nominal and measured size | Leaf width, height, thickness, and rebate dimensions |
| Orientation | Swing direction, handing, active edge, and frame side |
| Existing preparation | Mortise, faceplate, cylinder, spindle, follower, strike, and keeper |
| Frame condition | Frame type, stop position, rebate, reveal, fixing points, and movement |
| Adjacent hardware | Door closer, hold-open device, escape hardware, reader, and existing access controls |
| Evidence reference | Drawing number, photograph set, measurement sheet, and sample record |
| Current status | Unmeasured, measured, queried, trial-fitted, confirmed, or held |
Mark a door “not measured” rather than “standard.” If a future door replaces the surveyed leaf, the replacement enters the same measurement and release sequence. This prevents a fit approval from being transferred automatically to a visually similar door.
Turn the slk 238 door fit notes into a measurement record
A repeatable door thickness measurement is more useful than one nominal figure. Use a rigid steel rule or a verified measuring tool and record actual dimensions with units. Measure the leaf at several positions because timber, metal, composite, and previously modified doors can vary.
The table below is a field worksheet, not an SLK-238 compatibility list. The current supplier drawing defines which values and variations are acceptable.
| Measurement | Method | Record |
|---|---|---|
| Leaf thickness | Measure at the hinge, lock edge, and mid-span near the lock preparation | Three readings, minimum, maximum, and instrument used |
| Leaf width and height | Measure at top, middle, and bottom; include the finished surface | Actual dimensions rather than nominal sizes |
| Rebate | Measure depth, width, length, and position of the frame stop | Full-size profile and any existing seal |
| Lock-edge setback | Measure from the active door edge to the centreline of the mortise or spindle | Dimension and a marked photograph |
| Stile width | Measure usable face area beside the lock zone | Minimum available width and any obstruction |
| Frame depth | Measure from the door face to the rebate or stop | Full projection plus clearance |
| Handing and swing | Photograph the pull side and mark hinge, lock, and active edges | Direction, handing, and any floor restriction |
Photograph each dimension in context. A close-up should include the measuring tool and the edge from which the dimension is taken. Annotate the same photographs with the door identifier; loose image files quickly become unusable evidence.
Record any bevel, taper, bowed panel, uneven frame, or surface damage separately. Do not average these conditions into a passing number. Supplier acceptance criteria and permitted measurement methods must be confirmed on the dated product page for the specific SKU and in the current drawing pack.
Match the No. 2 hotel mortise to real door geometry
The catalogue record identifies the mortise as a No. 2 hotel mortise. That is a useful starting description, but the name alone does not prove compatibility with a particular door. The family label does not replace a cutout drawing, and an existing mortise should not be accepted merely because it looks similar.
Confirm on the dated product page for the specific SKU before using catalogue information in a purchase decision. The detailed catalogue treatment is also separated from fit in Data Memo: What the SLK-238 Data Sheet Actually Tells a Buyer.
| Interface | Field check | Evidence needed for acceptance |
|---|---|---|
| Mortise case | Measure case depth, width, height, fixing positions, and pocket clearance | Current SKU cutout drawing |
| Faceplate | Record length, width, screw centres, and active-edge setback | Faceplate drawing and marked door template |
| Backset and spindle | Measure the spindle centreline from the active edge; record spindle diameter, projection, and follower size | Dated dimensional drawing |
| Latch or bolt | Observe the required projection, throw, and relationship to the keeper | Assembly drawing and strike detail |
| Cylinder and override | Record opening, projection, and required internal clearance | Installation guide for the exact configuration |
| Strike and keeper | Measure frame positions, recess, fixing points, and keeper engagement | Frame and strike drawings |
For a retrofit, remove only what the approved procedure permits and preserve enough evidence to determine whether the existing preparation can be reused. If the door contains an unfamiliar mortise, measure it rather than adapting it informally. A revised spindle, faceplate, or keeper may affect the door structure and adjacent components.
The correct outcome is not necessarily reuse. It may be retain, modify, replace the mortise area, or select another door preparation. The decision must follow the current SKU evidence and the project’s approved construction plan.
Prove the panel envelope, not merely the lock body
The catalogue record for SLK-238 lists the panel dimensions as 301 × 73 × 24 mm. It also identifies the material as aluminum alloy and records Black, Silver, and Red antique bronze finishes. These are catalogue fields, not a complete installation envelope. Confirm on the dated product page for the specific SKU before using the dimensions for procurement or preparation.
Use the supplier drawing to check all of the following:
- The panel fits within the available stile and rebate without cutting into an engineered edge.
- The required fixing points have material behind them and do not conflict with the mortise.
- Projection beyond the door face leaves clearance for the frame, seal, closer, handle, and room-side traffic.
- The panel can be installed and serviced without removing adjacent hardware that must remain in service.
- Handing, handle position, reader orientation, and indicator visibility suit the door.
- Surface finish and edge conditions do not create a visible gap or an unusable rebate.
- The strike and keeper positions align without forcing the panel or frame.
The supplied SLK-238 dimensions should be checked against the complete drawing rather than marked “pass” on their own. A panel can be narrow enough while the spindle, cylinder, wiring route, or fixing pattern still fails. Keep the projected silhouette and every required clearance visible on the marked-up drawing.
Do not drill the production door until the preparation has been approved against the current drawing. If a visual template is used for a trial, mark it as a template and record which dimensions it represents.
Check operating interfaces around the prepared door
Mechanical fit is only one part of RFID hotel lock installation. The catalogue lists RFID/IC card access, mechanical override, hotel lock management software, a standalone lock, and a PC-linked card encoder with no in-room network required. It also lists guest card issuance, floor and room permissions, check-in validity windows, and unlock records. Confirm on the dated product page for the specific SKU because the operating configuration forms part of the released product definition.
The prepared door must support the intended operating sequence:
- Confirm that the card reader remains reachable in normal use and is not obstructed by a handle, privacy fitting, or stored furniture.
- Confirm that emergency access can be reached without adding hardware outside the documented configuration.
- Confirm that the battery compartment can be serviced without damaging the door finish or adjacent frame.
- Confirm that a door closer, hold-open device, reader, or other control can operate at the same time as the lock.
- Confirm that the room workflow supports the intended card issuance, validity window, override, and record review process.
The record states a supply of 4 × AA alkaline batteries and a standard low-battery alert. Confirm on the dated product page for the specific SKU, and use that evidence when deciding whether service access and stock procedures are adequate.
Door preparation must also respect any project-specific fire-door, egress, accessibility, and access-control constraints.
CONFIRM-WITH-LOCAL-AUTHORITY: Confirm fire-door, egress, accessibility, and access-control requirements with the authority and project professionals for the installation location.
For the credential and software side of the project, use the Regulatory Brief: SLK-238 Credential and Software Configuration Options to keep card issuance, permissions, validity periods, and records in one review cycle.
Accept the drawing pack as controlled evidence
The catalogue states that dimension drawings, an installation guide, and a full datasheet are available on request. Confirm on the dated product page for the specific SKU, then request the documents that apply to the quoted configuration. A collection of photographs sent at different times is not a controlled drawing pack.
| Document | Acceptance question | Owner |
|---|---|---|
| Dimension drawing | Does it identify the current SKU or configuration and show every preparation dimension? | Supplier technical contact |
| Installation guide | Are sequence, tool, fixing, and service-access requirements stated? | Installer and supplier |
| Mortise and faceplate detail | Can the field measurements be compared directly with the cutout? | Supplier technical contact |
| Panel and clearance drawing | Are projection, fixing zones, and adjacent clearances defined? | Supplier and installer |
| Sample procedure | What is checked, who records it, and what constitutes acceptance? | Installer and project representative |
| Revision record | Can the drawing used for approval be identified unambiguously? | Procurement manager |
| Change notice | How will a drawing or product revision affect an open order? | Procurement manager |
Mark the approved revision on every measurement sheet and sample record. When a newer document arrives, compare it with the previous revision before replacing it. Record whether the change affects preparation, operation, packaging, or only documentation. A revised catalogue photograph without a revised dimensional drawing does not close an old exception.
Compare common door scenarios before committing
The following decision-comparison table helps procurement distinguish a documented match from an assumption. It does not predict the result before measurement; it defines what each result requires.
| Door condition | Evidence available | Fit classification | Required action |
|---|---|---|---|
| New leaf matching the current drawing | Supplier drawing and field measurements agree | Confirmed on geometry | Complete trial fit and release if the sample is accepted |
| Existing leaf with a reusable mortise | Existing preparation is measured and matches the drawing | Conditional until trial fit | Verify spindle, faceplate, keeper, and panel clearance |
| Existing mortise only looks similar | No current drawing for the existing case | Unresolved | Hold and request the cutout dimensions |
| Door is thinner, wider, or more deeply rebated than the drawing allows | Measurements fall outside the documented envelope | Outside the recorded fit | Review preparation changes or another lock option |
| Door schedule changes after approval | New revision replaces the measured leaf | Approval withdrawn | Reopen measurement, drawing, and trial-fit gates |
| No field measurement exists | Only a nominal size is available | Unknown | Schedule a site survey before commercial release |
| Hardware crowds the lock zone | Closer, reader, trim, or escape device conflicts with the preparation | Interface exception | Record the clash and obtain an approved resolution |
This matrix should sit beside the door schedule, not replace it. A “confirmed” result belongs to a named door and drawing revision. It cannot be generalized to another leaf with the same nominal size, especially where the frame, handing, surface, or adjacent hardware differs.
When the fit record remains conditional, state the exact condition that must close it. “Check on site” is not a release condition. A useful condition names the measurement, drawing clause, sample step, responsible person, and evidence required.
Control the sample and route exceptions
Use the first installation or a representative sample to test the approved preparation, then document what was checked. The sample is a verification step, not a reason to improvise. If the door does not match the approved drawing, stop and record the discrepancy rather than enlarging, narrowing, or relocating a cutout without approval.
| Exception | Immediate containment | Evidence to close it |
|---|---|---|
| Panel or fixing zone conflicts with the door edge | Mark the affected area and do not drill | Revised drawing or written preparation change |
| Spindle or follower clearance is insufficient | Keep the current bore untouched | Supplier confirmation of the correct preparation |
| Faceplate or strike position is misaligned | Mark both door and frame positions | Marked drawing and revised frame check |
| Door closer or handle clashes with the panel | Remove only temporary obstructions | Interface approval and adjusted drawing or hardware layout |
| Handing is reversed or ambiguous | Suspend fitting and label the door | Correct handing record and rechecked measurement |
| Frame, leaf, or surface condition differs from the survey | Photograph and reassess the affected door | Updated measurement and revised fit decision |
Keep an exception log with the issue, affected doors, evidence, owner, and status. Decide whether the exception affects one door, a door type, a floor, or the project. If it changes the preparation for multiple doors, update the schedule and drawing package before work continues.
Record the trial-fit result by component: panel position, fixing access, spindle operation, latch or bolt engagement, strike alignment, handle movement, reader access, and service access. Do not reduce the result to “installed successfully.” A successful installation can still reveal an operating clash or an undocumented preparation change.
Release the fit package to procurement
The final fit package should contain the door schedule, measurement sheets, photographs, the current supplier drawing and installation guide, the marked template, the trial-fit record, the interface checklist, the exception log, and signed approvals. A single “fit confirmed” message is not enough to reconstruct the decision later.
| Approver | Must confirm | Signature meaning |
|---|---|---|
| Site surveyor | Measurements match the photographs and door identifiers | Field evidence is complete |
| Installer or fabricator | Preparation and trial fit follow the approved drawing | Physical work is traceable to the drawing |
| Supplier technical contact | Any deviation has an approved written answer | Technical exceptions are closed |
| Project operations or security lead | Access and adjacent-hardware workflow is workable | Operational constraints are accepted |
| Procurement manager | The package identifies the exact revision and released doors | Fit approval is granted for named doors |
Use the Checklist Tearoff: SLK-238 Purchase-Order Checklist: What to Confirm Before Ordering after the fit package is complete. Fit approval should be one controlled input to that checklist, not a substitute for the other commercial and configuration checks.
Do not treat confirmed fit as approval of the purchase order. A drawing revision, product configuration, delivery batch, packaging instruction, or order quantity may still require separate confirmation. If a released door is replaced after order placement, return that door to the fit gates before installation.
Send one preparation-ready request to the supplier
A focused request reduces clarification cycles and gives the supplier enough information to return a usable answer. Include the exact SLK-238 configuration being considered, but do not ask for a general compatibility statement that cannot be tied to a drawing.
The same question is worked through in more detail in the smart lock environmental specification. That is the same question slk 238 door fit notes has to answer here.Prepare the request with these fields:
- Project, supplier, requester, date, and required response date
- Door identifier and a marked leaf-and-frame drawing
- Measured leaf dimensions, rebate, backset, spindle, and existing mortise details
- Existing faceplate, strike, keeper, closer, and other adjacent hardware
- Photographs with scales and a reference to each measurement sheet
- Requested confirmation of current SKU drawings, cutout dimensions, panel envelope, and tolerances
- Requested installation, trial-fit, and change-notification procedure
- Required document language, revision format, and approval route
Ask the supplier to answer each deviation separately. A response such as “should work” is not a dimensioned acceptance. Require a marked drawing or written instruction that identifies the affected door and revision.
The commercially useful output from this runbook is not another catalogue image. It is a traceable fit decision that protects preparation effort, gives site teams one approved basis for work, and lets procurement order against known evidence. Send the completed package with a request for a quote when the drawing revision, configuration, and preparation details are ready for commercial review.

