Slk 235 door fit notes: compare SLK-235 replacement routes, verify door measurements, and plan a low-risk retrofit for hotel, homestay, and access-control.

Publicerad den: jun 28, 2024

SLK-235 Door Fit and Replacement Notes for Buyers

SLK-235 Door Fit and Replacement Notes for Buyers

For procurement managers comparing a retrofit, the slk 235 door fit notes should be treated as a decision record, not as an assumption that the lock will fit. The immediate question is whether the existing door leaf, mortise case, faceplate, strike, spindle and credential setup can accept the ordered SLK-235 configuration without avoidable drilling or door rework. That question comes before feature comparisons: a lock can be specified correctly and still fail at installation if the opening geometry is wrong.

Direct answer. In short, slk 235 door fit notes is the subject of this piece. slk 235 door fit notes is where the work on slk 235 door fit notes sits. slk-235 is what has to be evidenced before anyone signs. A slk 235 door fit notes is a component-level look at how the technology behaves. slk 235 door fit notes is where the limits sit. slk 235 door fit notes is verified on the dated product page.

slk 235 door fit notes is used here in the narrow sense set out in slk 235 door fit notes. It is a working definition built for slk 235 door fit notes. It is not a statutory one, and it has to be read against the market and product concerned.

  • Confirm the feature — confirm on the dated product page for the specific SKU behind slk 235 door fit notes
  • Confirm the constraint — record where the technology in slk-235 stops working
  • Confirm the contingency — name the mechanical path that remains if slk 235 door fit notes fails
  • For slk 235 door fit notes, slk 235 is what each step has to answer to.

This Comparison Arena sets four routes side by side: like-for-like exchange, mortise-case retention with an adapted panel, full lock-case replacement and a broader access control upgrade. For an RFID hotel lock replacement, it starts with what can be reused, then tests each remaining assumption against drawings, field measurements and the exact ordered configuration.

The replacement decision starts with four routes

Choose the replacement route from the opening evidence, not from the credential features visible on a sample. The table is a screening matrix for the procurement team.

Replacement routeUse it whenMain door workPrincipal riskEvidence required
Like-for-like exchangeThe existing case, faceplate, spindle and strike arrangement match the ordered drawingsRemove the old panel and install the replacementA concealed mismatch in the mortise cavityDated drawings plus a field measurement record
Retain the mortise case with an adapted panelThe internal case is usable, but the exterior panel or reader arrangement differsFit a documented adapter and align the new panelAn unapproved adapter or unsuitable panel footprintAdapter drawing, case condition record and fit check
Replace the lock case and strike systemThe case, fixing pattern, faceplate or bolt geometry does not matchReplace hardware and machine the door as requiredDoor-leaf damage or unsuitable machiningCut list, door-supplier acceptance and trial fit
Redesign the access-control workflowThe project needs different credential or management arrangementsFit a new panel and migrate the operating workflowInconsistent configurations across doorsWorkflow acceptance, configuration sheet and commissioning plan

A like-for-like route is the least disruptive only when the documents and the field opening agree. The redesign route can be justified by operational requirements, but it should not be used to conceal unresolved door geometry.

What the SLK-235 record can and cannot settle

The first-party catalogue supports an access and management comparison, but it does not supply installation geometry for this model family. SLK-235 records RFID/IC card and mechanical override as standard, while passcode and mobile-app support depend on the selected model version. Its platform is TTLock over Bluetooth, with hotel lock management software available on card-model versions. The listed functions include guest card issuance, floor and room permissions, check-in validity windows and unlock records.

Record pointSLK-235SLK-235-2SLK-235-3
AccessRFID/IC card standard; passcode and mobile app optional by model versionRFID/IC card and mechanical override standardRFID/IC card and mechanical override standard
ManagementTTLock over Bluetooth; hotel software available on card-model versionsPC-linked card encoder with guest cards; standalone operation and no in-room network requiredPC-linked card encoder with guest cards; standalone operation and no in-room network required
Style and finishHotel Card Lock or Homestay Password Lock; silverHotel Card Lock; silverHotel Card Lock; silver
Catalogue positionKeypad Door Lock and Smart Door LocksHotel Door Lock and Smart Door LocksKeypad Door Lock and Smart Door Locks
Physical and power recordDoor-fit and power fields are blankDoor-fit and power fields are blankDoor-fit and power fields are blank
DocumentationDimension drawings, installation guide and full datasheet available on requestSame documentation set available on requestSame documentation set available on request

A category label is not proof of a credential method. In particular, SLK-235-3 is catalogued under Keypad Door Lock, but its access row lists RFID/IC card rather than passcode. The slk 235 door fit notes must therefore distinguish catalogue wording from the ordered configuration. For every comparison that affects procurement, confirm on the dated product page for the specific SKU and request the drawings and configuration sheet for that suffix.

Build the smart lock door measurement record

A smart lock door measurement is not one dimension. It is a set of related values taken from named datums on the door, frame and existing hardware. Assign a unique door ID before collecting anything, because a photograph alone cannot show edge distance, cavity depth or the position of fixing holes.

Object to inspectMeasurement basisRecordDecision use
Door leafLock bore, latch edge and hinge sideThickness, width and any taperPanel and case insertion
BacksetDoor edge to the datum defined by the lock drawingValue and datum usedSpindle and case alignment
SpindleBoth ends of the existing installationDiameter, length and sectionHandle or lever connection
Lock body and mortise caseFull case envelopeWidth, height, depth and fixing centresCavity compatibility
FaceplateComplete outline and fixing holesDimensions and thicknessDoor-edge coverage
Door-frame rebateOpen cavityWidth and depthCase clearance
Latch or deadboltDoor edge and strike faceProjection, throw and shapeClosing and strike engagement
Strike plate and keeperJamb and frame depthDimensions, fixings and keeper positionBolt engagement
Panel boresCentre lines from the door edgePositions and diametersReader and keypad alignment
Door swing and closerHinge, frame and closer positionsHand, swing and available clearanceLever and panel operation

State whether each value is measured, taken from the old lock, or copied from a drawing. Do not mix those sources without identifying them. A measured value can reveal a different installation condition; a drawing value describes only the design.

flowchart TD
  A[Assign door ID and exact SKU] --> B[Measure leaf and mortise geometry]
  B --> C[Compare drawings with field parts]
  C --> D{Geometry matches the ordered configuration}
  D -->|Yes| E[Use like-for-like replacement route]
  D -->|No| F[Check adapter or full case replacement]
  E --> G[Install, test and document]
  F --> G

The decision output should show which parts remain, which must change and which remain unresolved. That distinction prevents a replacement quote from hiding door preparation, machining or software conversion.

Route A — a like-for-like exchange when the drawings match

A direct exchange is appropriate when the existing mortise case and exterior interfaces match the replacement drawings. The buyer should request the dated dimension drawings, installation guide and full datasheet for the exact SLK-235 configuration, then compare them with the physical lock and the field measurements.

The approval evidence should cover:

  • Lock body compatibility with the existing case dimensions and fixing pattern.
  • Spindle, handle or lever, and mechanical-key interfaces.
  • Faceplate, latch or deadbolt, and strike alignment.
  • Panel footprint and the position of reader, keypad or emergency-access features.
  • The intended RFID, passcode, app and management configuration.

An illustrative scenario: after the escutcheon is removed, a surveyor sees a case with apparently unchanged fixing centres and spindle line. That observation starts the comparison; it does not prove compatibility. Trial-fit the lock, confirm the door closes without forcing, and complete a small pilot before approving the same operation across a room block.

Route B — retain the mortise case with a documented adapter

This mortise lock retrofit route can reduce work at the door edge when the internal case remains serviceable and the new panel needs a different reader, handle or control arrangement. It remains a replacement project, however, because an adapter becomes part of the mechanical and credential interface.

The buyer should verify the case condition, fixing points, tail components, spindle connection, panel backing and any routing required for the selected control arrangement. An adapter drawing must identify the permitted old case, the new panel and the installation sequence. Do not approve a generic universal plate or rely on visual similarity between the old and new panels.

Illustrative scenario: the mortise case appears undamaged, but the new escutcheon is wider and the reader position differs. If the manufacturer or supplier has not documented that adapter for the exact combination, the route remains on hold. Record the intended adapter revision with the door and the ordered SKU so installation staff cannot substitute an unverified part.

Route C — replace the lock case and strike system

A full lock-case replacement is the appropriate comparison when the existing case, fixing pattern, faceplate or bolt geometry differs materially from the ordered SLK-235 configuration. It may also be necessary when the old case is damaged, but the case condition should be inspected before that decision is made.

The procurement sequence is straightforward: remove the old hardware, inspect the cavity, trial-fit the replacement, obtain the agreed cut list, machine only the required openings, install the case and strike system, and repeat the fit check before final fixing. Photograph each stage against the same door ID.

Door modification can engage fire-door, egress, accessibility and building requirements that vary by opening and jurisdiction. Do not infer approval from a lock drawing.

CONFIRM-WITH-LOCAL-AUTHORITY: Confirm fire-door, egress, accessibility and building requirements for each opening with the authority having jurisdiction, the door supplier and the project approver.

Where the leaf is valuable or already finished, compare the operational disruption of this route with a new door or a retained case. The commercial comparison should identify machining, patching, reinstallation and potential leaf replacement as separate work items rather than burying them inside the lock description.

Route D — use the project to upgrade access control

An access control upgrade changes the comparison from physical replacement to operating design. Decide whether the doors need RFID cards only, a passcode-capable version, a mobile-app version, or a common hotel management workflow. Then compare that decision with the legacy lock, the existing credential process and the records the site must retain.

For the catalogue-defined versions, SLK-235 can be ordered with a passcode keypad or TTLock smart-app configuration, while card-model versions support the listed hotel management functions. SLK-235-2 and SLK-235-3 are recorded as RFID/IC card models using a PC-linked card encoder, standalone lock operation and guest-card workflows; the records state that no in-room network is required. SLK-235-3 still needs to be treated as an RFID catalogue record unless the ordered configuration states otherwise.

The migration test is not simply whether a card opens the door. Check guest-card issuance, floor and room permissions, validity windows, unlock records, issue handling, lost-card response and the operating roles that issue or revoke credentials. The broader credential and software comparison is covered in How Credentials and Management Software Work on SLK-235.

Compare disruption, evidence and operational conversion

The route matrix below compares the consequences a procurement manager should evaluate. The ratings are screening judgments, not claims about a particular installation.

Decision factorLike-for-like exchangeAdapted panelFull case replacementAccess-control redesign
Door alterationUsually lowest if geometry matchesLow to moderateModerate to highDepends on selected hardware
Hardware retainedExisting case may remainMortise case retainedLittle of the lock system retainedDepends on project scope
Credential conversionDirect when the access profile stays similarReader and card workflow must be checkedFull door-set retestingWorkflow and credential migration
Main evidence loadDrawing-to-field comparisonAdapter and case-compatibility recordsCut list and door acceptanceConfiguration and operating acceptance
Operational riskIncorrect hidden geometryUnapproved adaptationMachining or door-leaf conditionInconsistent versions or user practices
Rollback positionExisting parts may be available if retainedOriginal panel may not be directly restorableOriginal hardware is removedOriginal workflow may not remain available

Ask each option to separate the replacement lock, door preparation, strike changes, credential issuance, operator training and record migration in its quotation. A lower hardware line item may still create more site disruption if conversion work is omitted. The comparison should expose those work packages without assigning unsupported cost or timing figures.

Turn the survey into a door replacement checklist

The door replacement checklist should follow the door ID and use one evidence source for each field. Any unfilled or conflicting field remains a hold rather than an assumed value.

  • Record the building, floor, room and door reference.
  • Attach a full-leaf photograph and a close photograph of the existing lock.
  • Identify the current lock, panel, mortise case and strike arrangement.
  • Record leaf thickness at the lock, edge and hinge side.
  • Record leaf width, backset, spindle and relevant bore positions.
  • Measure the lock case, rebate, faceplate, latch or deadbolt and strike.
  • Note door hand, swing, closer position and panel-clearance constraints.
  • State the exact SLK-235 version and ordered access configuration.
  • State the credential platform and required management functions.
  • Request the dated dimension drawings, installation guide and full datasheet.
  • Identify the power source from the exact SKU documents; the catalogue power field is blank.
  • Record who will approve the fit, configuration and commissioning evidence.

Attach the completed checklist to the door schedule rather than storing it as a general survey note. That allows the installation team to trace each physical decision back to the purchase order and the product configuration under review.

Sequence the installation without hiding rework

A controlled sequence keeps the replacement decision visible through handover. The goal is to discover geometry conflicts before the new escutcheon conceals them.

  1. Complete the survey before ordering non-returnable hardware.
  2. Compare the survey with drawings for the exact ordered SKU.
  3. Remove the existing escutcheon and inspect the exposed case.
  4. Trial-fit the proposed case or adapter without final fixing.
  5. Resolve any drilling, faceplate or strike issue against the approved cut list.
  6. Install the case and panel in the documented sequence.
  7. Connect and test the handle, spindle and mechanical override.
  8. Apply the power arrangement stated in the exact SKU documentation.
  9. Configure the ordered RFID, passcode or app version.
  10. Test guest cards or other credentials against the approved workflow.
  11. Record unlock events and complete operating handover.

Do not infer battery count, voltage, external power override or other power provisions from a category or a related model. Those fields are blank in the first-party record for these versions and must be confirmed for the specific SKU.

Test physical fit and credential operation separately

Physical acceptance and electronic acceptance should have separate evidence. A lock can align correctly while its credential record is wrong, or a card can work while the door is being forced against an incorrect strike.

TestPass evidenceRecord against
Panel and case clearanceNo interference in the stated door swingDoor ID and drawing revision
Spindle and handle operationHandle operates without binding or forcingLock body and spindle record
Latch or bolt engagementBolt enters the keeper without door-leaf distortionStrike and faceplate record
Door closureDoor closes and latches in its normal positionOpening ID and adjustment note
Mechanical overrideOverride operates according to the exact instructionsSKU and access configuration
RFID credentialIssued credential opens the assigned doorCard or credential test record
Passcode or app versionFunction operates only when orderedConfiguration sheet and test entry
Management recordsGuest issuance, permissions and unlock events appear as requiredWorkflow acceptance record
Operational checksDoor behaviour matches the approved operating scenarioCommissioning sign-off

Any conditional test should remain conditional. Do not record a passcode or mobile-app test as complete when the ordered model version does not include that method.

Use a procurement scorecard with evidence-based gates

The scorecard should expose gaps before release rather than average them away. Pass, hold and fail are more useful than a weighted total when physical compatibility is a non-negotiable condition.

GatePass evidenceHold or fail trigger
Physical fitApproved drawing, measurement and fit-check recordUnresolved dimension or unapproved machining
SKU and configurationExact suffix and access-method confirmationConfiguration shown only as “optional”
Credential workflowIssued test credential and recorded permissionsUntested migration or mixed versions
Mechanical accessOverride and handle test completedIncomplete operating procedure
Management recordsUnlock-record and guest-issuance testRecords cannot be reviewed as required
Site requirementsRelevant local and door-supplier confirmationApproval scope remains undefined
Document packDrawings, guide, datasheet and configuration attachedSupplier cannot tie documents to the ordered SKU

A release should require every physical-fit gate to pass. It should also require the configuration and credential gates to pass for the doors in that release. The procurement team can then use A SLK-235 Order Review: Items to Confirm Before Release to reconcile the site survey, order record and acceptance evidence.

Connect the survey, specifications and order records

Use the documents as a chain rather than separate downloads. The Office Smart Lock Site Survey and Smart Lock Retrofit Site Survey support field collection, while SLK-235 Specifications, Field by Field helps separate recorded capabilities from blank fields.

For credential decisions, use How Credentials and Management Software Work on SLK-235. For release control, use A SLK-235 Order Review: Items to Confirm Before Release. The order review should point back to the same door IDs, exact SKU suffixes, drawings and test records used during the survey. That traceability prevents a valid product document from being applied to the wrong door configuration.

Close the remaining evidence gaps before release

The unresolved items are known because the first-party door-fit and power fields are blank. Before approval, obtain the applicable door thickness range, panel dimensions, lock-body and mortise dimensions, spindle information, faceplate and strike details, and the documented power arrangement for the exact SKU.

The same question is worked through in more detail in how to choose a connected smart lock system. That is the same question slk 235 door fit notes has to answer here.Also close the configuration gaps: credential method, management platform, guest-card workflow, mechanical override arrangement, environment conditions, packing requirements and any OEM/ODM logo, finish, packaging, manual or configuration requirements.

Send the completed door schedule, survey photographs, exact configuration request and required document list with the request a quote. An approved SLK-235 replacement should leave one traceable chain from the existing opening to the selected route, ordered configuration, installation record and operational handover.

Din kundvagn
Din upplevelse på denna webbplats förbättras om du tillåter cookies. Cookiepolicy
Chat on WhatsApp