SLK-235 Door Fit and Replacement Notes for Buyers
For procurement managers comparing a retrofit, the slk 235 door fit notes should be treated as a decision record, not as an assumption that the lock will fit. The immediate question is whether the existing door leaf, mortise case, faceplate, strike, spindle and credential setup can accept the ordered SLK-235 configuration without avoidable drilling or door rework. That question comes before feature comparisons: a lock can be specified correctly and still fail at installation if the opening geometry is wrong.
Direct answer. In short, slk 235 door fit notes is the subject of this piece. slk 235 door fit notes is where the work on slk 235 door fit notes sits. slk-235 is what has to be evidenced before anyone signs. A slk 235 door fit notes is a component-level look at how the technology behaves. slk 235 door fit notes is where the limits sit. slk 235 door fit notes is verified on the dated product page.
slk 235 door fit notes is used here in the narrow sense set out in slk 235 door fit notes. It is a working definition built for slk 235 door fit notes. It is not a statutory one, and it has to be read against the market and product concerned.
- Confirm the feature — confirm on the dated product page for the specific SKU behind slk 235 door fit notes
- Confirm the constraint — record where the technology in slk-235 stops working
- Confirm the contingency — name the mechanical path that remains if slk 235 door fit notes fails
- For slk 235 door fit notes, slk 235 is what each step has to answer to.
This Comparison Arena sets four routes side by side: like-for-like exchange, mortise-case retention with an adapted panel, full lock-case replacement and a broader access control upgrade. For an RFID hotel lock replacement, it starts with what can be reused, then tests each remaining assumption against drawings, field measurements and the exact ordered configuration.
The replacement decision starts with four routes
Choose the replacement route from the opening evidence, not from the credential features visible on a sample. The table is a screening matrix for the procurement team.
| Replacement route | Use it when | Main door work | Principal risk | Evidence required |
|---|---|---|---|---|
| Like-for-like exchange | The existing case, faceplate, spindle and strike arrangement match the ordered drawings | Remove the old panel and install the replacement | A concealed mismatch in the mortise cavity | Dated drawings plus a field measurement record |
| Retain the mortise case with an adapted panel | The internal case is usable, but the exterior panel or reader arrangement differs | Fit a documented adapter and align the new panel | An unapproved adapter or unsuitable panel footprint | Adapter drawing, case condition record and fit check |
| Replace the lock case and strike system | The case, fixing pattern, faceplate or bolt geometry does not match | Replace hardware and machine the door as required | Door-leaf damage or unsuitable machining | Cut list, door-supplier acceptance and trial fit |
| Redesign the access-control workflow | The project needs different credential or management arrangements | Fit a new panel and migrate the operating workflow | Inconsistent configurations across doors | Workflow acceptance, configuration sheet and commissioning plan |
A like-for-like route is the least disruptive only when the documents and the field opening agree. The redesign route can be justified by operational requirements, but it should not be used to conceal unresolved door geometry.
What the SLK-235 record can and cannot settle
The first-party catalogue supports an access and management comparison, but it does not supply installation geometry for this model family. SLK-235 records RFID/IC card and mechanical override as standard, while passcode and mobile-app support depend on the selected model version. Its platform is TTLock over Bluetooth, with hotel lock management software available on card-model versions. The listed functions include guest card issuance, floor and room permissions, check-in validity windows and unlock records.
| Record point | SLK-235 | SLK-235-2 | SLK-235-3 |
|---|---|---|---|
| Access | RFID/IC card standard; passcode and mobile app optional by model version | RFID/IC card and mechanical override standard | RFID/IC card and mechanical override standard |
| Management | TTLock over Bluetooth; hotel software available on card-model versions | PC-linked card encoder with guest cards; standalone operation and no in-room network required | PC-linked card encoder with guest cards; standalone operation and no in-room network required |
| Style and finish | Hotel Card Lock or Homestay Password Lock; silver | Hotel Card Lock; silver | Hotel Card Lock; silver |
| Catalogue position | Keypad Door Lock and Smart Door Locks | Hotel Door Lock and Smart Door Locks | Keypad Door Lock and Smart Door Locks |
| Physical and power record | Door-fit and power fields are blank | Door-fit and power fields are blank | Door-fit and power fields are blank |
| Documentation | Dimension drawings, installation guide and full datasheet available on request | Same documentation set available on request | Same documentation set available on request |
A category label is not proof of a credential method. In particular, SLK-235-3 is catalogued under Keypad Door Lock, but its access row lists RFID/IC card rather than passcode. The slk 235 door fit notes must therefore distinguish catalogue wording from the ordered configuration. For every comparison that affects procurement, confirm on the dated product page for the specific SKU and request the drawings and configuration sheet for that suffix.
Build the smart lock door measurement record
A smart lock door measurement is not one dimension. It is a set of related values taken from named datums on the door, frame and existing hardware. Assign a unique door ID before collecting anything, because a photograph alone cannot show edge distance, cavity depth or the position of fixing holes.
| Object to inspect | Measurement basis | Record | Decision use |
|---|---|---|---|
| Door leaf | Lock bore, latch edge and hinge side | Thickness, width and any taper | Panel and case insertion |
| Backset | Door edge to the datum defined by the lock drawing | Value and datum used | Spindle and case alignment |
| Spindle | Both ends of the existing installation | Diameter, length and section | Handle or lever connection |
| Lock body and mortise case | Full case envelope | Width, height, depth and fixing centres | Cavity compatibility |
| Faceplate | Complete outline and fixing holes | Dimensions and thickness | Door-edge coverage |
| Door-frame rebate | Open cavity | Width and depth | Case clearance |
| Latch or deadbolt | Door edge and strike face | Projection, throw and shape | Closing and strike engagement |
| Strike plate and keeper | Jamb and frame depth | Dimensions, fixings and keeper position | Bolt engagement |
| Panel bores | Centre lines from the door edge | Positions and diameters | Reader and keypad alignment |
| Door swing and closer | Hinge, frame and closer positions | Hand, swing and available clearance | Lever and panel operation |
State whether each value is measured, taken from the old lock, or copied from a drawing. Do not mix those sources without identifying them. A measured value can reveal a different installation condition; a drawing value describes only the design.
flowchart TD
A[Assign door ID and exact SKU] --> B[Measure leaf and mortise geometry]
B --> C[Compare drawings with field parts]
C --> D{Geometry matches the ordered configuration}
D -->|Yes| E[Use like-for-like replacement route]
D -->|No| F[Check adapter or full case replacement]
E --> G[Install, test and document]
F --> G
The decision output should show which parts remain, which must change and which remain unresolved. That distinction prevents a replacement quote from hiding door preparation, machining or software conversion.
Route A — a like-for-like exchange when the drawings match
A direct exchange is appropriate when the existing mortise case and exterior interfaces match the replacement drawings. The buyer should request the dated dimension drawings, installation guide and full datasheet for the exact SLK-235 configuration, then compare them with the physical lock and the field measurements.
The approval evidence should cover:
- Lock body compatibility with the existing case dimensions and fixing pattern.
- Spindle, handle or lever, and mechanical-key interfaces.
- Faceplate, latch or deadbolt, and strike alignment.
- Panel footprint and the position of reader, keypad or emergency-access features.
- The intended RFID, passcode, app and management configuration.
An illustrative scenario: after the escutcheon is removed, a surveyor sees a case with apparently unchanged fixing centres and spindle line. That observation starts the comparison; it does not prove compatibility. Trial-fit the lock, confirm the door closes without forcing, and complete a small pilot before approving the same operation across a room block.
Route B — retain the mortise case with a documented adapter
This mortise lock retrofit route can reduce work at the door edge when the internal case remains serviceable and the new panel needs a different reader, handle or control arrangement. It remains a replacement project, however, because an adapter becomes part of the mechanical and credential interface.
The buyer should verify the case condition, fixing points, tail components, spindle connection, panel backing and any routing required for the selected control arrangement. An adapter drawing must identify the permitted old case, the new panel and the installation sequence. Do not approve a generic universal plate or rely on visual similarity between the old and new panels.
Illustrative scenario: the mortise case appears undamaged, but the new escutcheon is wider and the reader position differs. If the manufacturer or supplier has not documented that adapter for the exact combination, the route remains on hold. Record the intended adapter revision with the door and the ordered SKU so installation staff cannot substitute an unverified part.
Route C — replace the lock case and strike system
A full lock-case replacement is the appropriate comparison when the existing case, fixing pattern, faceplate or bolt geometry differs materially from the ordered SLK-235 configuration. It may also be necessary when the old case is damaged, but the case condition should be inspected before that decision is made.
The procurement sequence is straightforward: remove the old hardware, inspect the cavity, trial-fit the replacement, obtain the agreed cut list, machine only the required openings, install the case and strike system, and repeat the fit check before final fixing. Photograph each stage against the same door ID.
Door modification can engage fire-door, egress, accessibility and building requirements that vary by opening and jurisdiction. Do not infer approval from a lock drawing.
CONFIRM-WITH-LOCAL-AUTHORITY: Confirm fire-door, egress, accessibility and building requirements for each opening with the authority having jurisdiction, the door supplier and the project approver.
Where the leaf is valuable or already finished, compare the operational disruption of this route with a new door or a retained case. The commercial comparison should identify machining, patching, reinstallation and potential leaf replacement as separate work items rather than burying them inside the lock description.
Route D — use the project to upgrade access control
An access control upgrade changes the comparison from physical replacement to operating design. Decide whether the doors need RFID cards only, a passcode-capable version, a mobile-app version, or a common hotel management workflow. Then compare that decision with the legacy lock, the existing credential process and the records the site must retain.
For the catalogue-defined versions, SLK-235 can be ordered with a passcode keypad or TTLock smart-app configuration, while card-model versions support the listed hotel management functions. SLK-235-2 and SLK-235-3 are recorded as RFID/IC card models using a PC-linked card encoder, standalone lock operation and guest-card workflows; the records state that no in-room network is required. SLK-235-3 still needs to be treated as an RFID catalogue record unless the ordered configuration states otherwise.
The migration test is not simply whether a card opens the door. Check guest-card issuance, floor and room permissions, validity windows, unlock records, issue handling, lost-card response and the operating roles that issue or revoke credentials. The broader credential and software comparison is covered in How Credentials and Management Software Work on SLK-235.
Compare disruption, evidence and operational conversion
The route matrix below compares the consequences a procurement manager should evaluate. The ratings are screening judgments, not claims about a particular installation.
| Decision factor | Like-for-like exchange | Adapted panel | Full case replacement | Access-control redesign |
|---|---|---|---|---|
| Door alteration | Usually lowest if geometry matches | Low to moderate | Moderate to high | Depends on selected hardware |
| Hardware retained | Existing case may remain | Mortise case retained | Little of the lock system retained | Depends on project scope |
| Credential conversion | Direct when the access profile stays similar | Reader and card workflow must be checked | Full door-set retesting | Workflow and credential migration |
| Main evidence load | Drawing-to-field comparison | Adapter and case-compatibility records | Cut list and door acceptance | Configuration and operating acceptance |
| Operational risk | Incorrect hidden geometry | Unapproved adaptation | Machining or door-leaf condition | Inconsistent versions or user practices |
| Rollback position | Existing parts may be available if retained | Original panel may not be directly restorable | Original hardware is removed | Original workflow may not remain available |
Ask each option to separate the replacement lock, door preparation, strike changes, credential issuance, operator training and record migration in its quotation. A lower hardware line item may still create more site disruption if conversion work is omitted. The comparison should expose those work packages without assigning unsupported cost or timing figures.
Turn the survey into a door replacement checklist
The door replacement checklist should follow the door ID and use one evidence source for each field. Any unfilled or conflicting field remains a hold rather than an assumed value.
- Record the building, floor, room and door reference.
- Attach a full-leaf photograph and a close photograph of the existing lock.
- Identify the current lock, panel, mortise case and strike arrangement.
- Record leaf thickness at the lock, edge and hinge side.
- Record leaf width, backset, spindle and relevant bore positions.
- Measure the lock case, rebate, faceplate, latch or deadbolt and strike.
- Note door hand, swing, closer position and panel-clearance constraints.
- State the exact SLK-235 version and ordered access configuration.
- State the credential platform and required management functions.
- Request the dated dimension drawings, installation guide and full datasheet.
- Identify the power source from the exact SKU documents; the catalogue power field is blank.
- Record who will approve the fit, configuration and commissioning evidence.
Attach the completed checklist to the door schedule rather than storing it as a general survey note. That allows the installation team to trace each physical decision back to the purchase order and the product configuration under review.
Sequence the installation without hiding rework
A controlled sequence keeps the replacement decision visible through handover. The goal is to discover geometry conflicts before the new escutcheon conceals them.
- Complete the survey before ordering non-returnable hardware.
- Compare the survey with drawings for the exact ordered SKU.
- Remove the existing escutcheon and inspect the exposed case.
- Trial-fit the proposed case or adapter without final fixing.
- Resolve any drilling, faceplate or strike issue against the approved cut list.
- Install the case and panel in the documented sequence.
- Connect and test the handle, spindle and mechanical override.
- Apply the power arrangement stated in the exact SKU documentation.
- Configure the ordered RFID, passcode or app version.
- Test guest cards or other credentials against the approved workflow.
- Record unlock events and complete operating handover.
Do not infer battery count, voltage, external power override or other power provisions from a category or a related model. Those fields are blank in the first-party record for these versions and must be confirmed for the specific SKU.
Test physical fit and credential operation separately
Physical acceptance and electronic acceptance should have separate evidence. A lock can align correctly while its credential record is wrong, or a card can work while the door is being forced against an incorrect strike.
| Test | Pass evidence | Record against |
|---|---|---|
| Panel and case clearance | No interference in the stated door swing | Door ID and drawing revision |
| Spindle and handle operation | Handle operates without binding or forcing | Lock body and spindle record |
| Latch or bolt engagement | Bolt enters the keeper without door-leaf distortion | Strike and faceplate record |
| Door closure | Door closes and latches in its normal position | Opening ID and adjustment note |
| Mechanical override | Override operates according to the exact instructions | SKU and access configuration |
| RFID credential | Issued credential opens the assigned door | Card or credential test record |
| Passcode or app version | Function operates only when ordered | Configuration sheet and test entry |
| Management records | Guest issuance, permissions and unlock events appear as required | Workflow acceptance record |
| Operational checks | Door behaviour matches the approved operating scenario | Commissioning sign-off |
Any conditional test should remain conditional. Do not record a passcode or mobile-app test as complete when the ordered model version does not include that method.
Use a procurement scorecard with evidence-based gates
The scorecard should expose gaps before release rather than average them away. Pass, hold and fail are more useful than a weighted total when physical compatibility is a non-negotiable condition.
| Gate | Pass evidence | Hold or fail trigger |
|---|---|---|
| Physical fit | Approved drawing, measurement and fit-check record | Unresolved dimension or unapproved machining |
| SKU and configuration | Exact suffix and access-method confirmation | Configuration shown only as “optional” |
| Credential workflow | Issued test credential and recorded permissions | Untested migration or mixed versions |
| Mechanical access | Override and handle test completed | Incomplete operating procedure |
| Management records | Unlock-record and guest-issuance test | Records cannot be reviewed as required |
| Site requirements | Relevant local and door-supplier confirmation | Approval scope remains undefined |
| Document pack | Drawings, guide, datasheet and configuration attached | Supplier cannot tie documents to the ordered SKU |
A release should require every physical-fit gate to pass. It should also require the configuration and credential gates to pass for the doors in that release. The procurement team can then use A SLK-235 Order Review: Items to Confirm Before Release to reconcile the site survey, order record and acceptance evidence.
Connect the survey, specifications and order records
Use the documents as a chain rather than separate downloads. The Office Smart Lock Site Survey and Smart Lock Retrofit Site Survey support field collection, while SLK-235 Specifications, Field by Field helps separate recorded capabilities from blank fields.
For credential decisions, use How Credentials and Management Software Work on SLK-235. For release control, use A SLK-235 Order Review: Items to Confirm Before Release. The order review should point back to the same door IDs, exact SKU suffixes, drawings and test records used during the survey. That traceability prevents a valid product document from being applied to the wrong door configuration.
Close the remaining evidence gaps before release
The unresolved items are known because the first-party door-fit and power fields are blank. Before approval, obtain the applicable door thickness range, panel dimensions, lock-body and mortise dimensions, spindle information, faceplate and strike details, and the documented power arrangement for the exact SKU.
The same question is worked through in more detail in how to choose a connected smart lock system. That is the same question slk 235 door fit notes has to answer here.Also close the configuration gaps: credential method, management platform, guest-card workflow, mechanical override arrangement, environment conditions, packing requirements and any OEM/ODM logo, finish, packaging, manual or configuration requirements.
Send the completed door schedule, survey photographs, exact configuration request and required document list with the request a quote. An approved SLK-235 replacement should leave one traceable chain from the existing opening to the selected route, ordered configuration, installation record and operational handover.

