Slk 233 door fit notes: use this SLK-233 reverse-mount replacement checklist to measure doors, verify clearances, plan lock changes, and record supplier.

Опубликовано: июл 27, 2023

Replacing Doors or Locks with SLK-233: A Fit Checklist

Replacing Doors or Locks with SLK-233: A Fit Checklist

Replacing a door or a lock can look like a hardware decision until the site measurements arrive. These slk 233 door fit notes turn the work into a sequence of evidence gates: identify what is changing, measure the opening, obtain current drawings, reconcile differences, and approve the fit before ordering.

Direct answer. In brief, this article covers slk 233 door fit notes from slk 233 door fit notes to slk-233. It states what to confirm about slk 233 door fit notes on the dated product page where a figure is involved. A slk 233 door fit notes treats one component on its own terms. slk 233 door fit notes names the tests that close it. slk 233 door fit notes is not accepted on a headline figure.

On slk 233 door fit notes, this article uses slk 233 door fit notes as the definition. It treats slk 233 door fit notes as a working definition specific to this market and product, rather than a general one.

  • Verify the function — confirm on the dated product page for the specific SKU behind slk 233 door fit notes
  • Verify the boundary — record where the technology in slk-233 stops working
  • Verify the backup — name the mechanical path that remains if slk 233 door fit notes fails
  • Treat this as the slk 233 door fit notes sequence, with slk 233 as the reference.

The catalogue record identifies the SLK-233 as a reverse-mount RFID card door lock in a hotel card lock style. Its published Door fit field is recorded as —, so it does not supply an applicable door thickness, door type, or dimensional drawing for procurement use. The record must be expanded through dated drawings and site measurements rather than inference.

This document is therefore a process for deciding what to replace and how to prove compatibility. It does not replace the supplier drawing, an installer’s site check, or a controlled fit sample.

Set the replacement boundary before the measurements start

Assign every affected opening a unique identification number. Record the room or opening reference, door type, existing lock type, frame description, and the reason for replacement in one line. If several openings appear identical, measure each one; the label “same door type” is not evidence that dimensions and hardware positions match.

The replacement boundary must also distinguish a planned product choice from a still-open selection. The catalogue lists RFID/IC card access and a mechanical override for the SLK-233, together with hotel lock management software, a PC-linked card encoder, guest cards, floor and room permissions, check-in validity windows, and unlock records. Confirm on the dated product page for the specific SKU before relying on any of those fields for procurement. The comparison the same buyer runs first is SLK-9905A Procurement Checklist for Hotel Projects.

Use the published specification as a starting point, not as a fit approval. The companion article SLK-233: Reading the Published Specification Without Guesswork explains which recorded fields can answer a question and which fields require dated evidence from the supplier.

Capture the decision owner

The fit file should identify one person responsible for site records, one person responsible for supplier documentation, and the installer or site reviewer who will perform the final comparison. A procurement manager can coordinate these records without turning the estimate into an unverified dimensional claim.

If another lock model is still under consideration, keep it in a separate option column. Do not allow features from the alternative model to fill gaps in the SLK-233 record.

Use a gated sequence instead of a single approval request

The order of work matters because a drawing requested before the opening is measured can only answer part of the question. Likewise, a sample checked before the drawing revision is fixed may test the wrong version.

flowchart TD
    A[Record opening and scope] --> B[Measure door and frame]
    B --> C[Obtain dated SLK-233 documents]
    C --> D{Fit data covers the site geometry?}
    D -->|Yes| E[Build controlled fit sample]
    D -->|No| F[Hold and close the evidence gap]
    E --> G{Physical fit passes?}
    G -->|Yes| H[Release procurement approval]
    G -->|No| F
    F --> C
StageWork at this stageOutputGate to the next stage
ScopeDefine the opening and replacement boundaryOpening scheduleA named decision owner accepts the scope
MeasureRecord door, frame, case, latch, strike, and hardware geometrySite measurement sheetRequired fields are complete
DocumentRequest current drawings, guide, and datasheetSupplier evidence packDrawings match the quoted SKU
ReconcileCompare supplier geometry with site recordsExceptions listEvery conflict has a resolution
SampleCheck a controlled sample against the openingFit-test recordMechanical operation and clearance pass
ApproveFreeze the drawing and commercial configurationSigned fit decisionProcurement may release the order

A stage is complete only when its output exists in the project record. A verbal assurance, an unlabeled photograph, or an undated sketch should not close a gate.

Decide whether the door, lock, or both are changing

Begin by stating what the project actually replaces. Changing the lock preserves the door leaf, frame, rebate, and most fixed hardware. Replacing the leaf may change thickness, rebate geometry, fixing positions, and clearance relationships even if the opening width is unchanged. A hotel door retrofit can also combine either path with changed access-control requirements.

Treat the slk 233 door fit notes as separate work packages for each case. This prevents the dimensions of a replacement door from being copied into a lock-only estimate or the case of an existing lock from being carried into a new-door order.

Replacement pathWhat must be measuredMain fit riskRequired proof
Lock onlyExisting case, backset, spindle, cylinder, latch or bolt, strike, and panel positionThe new lock cannot occupy the recorded case or reach the existing strikeSupplier drawing compared with site measurements and a fit sample
Door leaf onlyLeaf thickness, rebate, fixing points, and required hardware positionsThe supplied leaf differs from the frame or the existing lock interfaceDoor schedule, dimensioned sketch, and supplier confirmation against that schedule
Door leaf and lockBoth existing geometry and the complete new interfaceErrors in either scope can cancel the otherOne combined fit record covering the final assembly
Frame or rebate modificationExisting frame condition and the exact alteration proposedWork expands beyond the original replacement scopeRevised drawings and site approval before alteration

Do not use this checklist as approval for an opening with special fire-rating, emergency-egress, or life-safety constraints. The project record must identify the relevant reviewer and the evidence required for that opening.

CONFIRM-WITH-LOCAL-FIRE-AND-EGRESS-REVIEW

Build the door measurement checklist without guesswork

A useful door measurement checklist records the actual opening rather than a catalogue label. Use the same units throughout, identify the measurement point, and attach a scaled photograph showing where the tape or calliper was placed. Record nominal frame information separately from measured site information.

ItemSite methodEvidence to retain
Door leaf thicknessMeasure at the lock position and away from hardwareDimension, location, and photograph
Leaf width and heightMeasure the leaf itself, not only the frame openingOverall dimension sketch
Frame opening and rebateRecord width, depth, and rebate dimensions at the lock areaSection sketch with dimensions
Lock case pocketMeasure length, width, and depth of the opening in the leafMarked photograph
Faceplate areaMeasure plate width and height plus fixing positionsDirect outline or sketch
Lock body backsetMeasure from the door edge to the spindle or cylinder referenceDimensioned edge view
Spindle and fixing patternRecord square section, centres, and fixing locationsPhotograph and dimension drawing
Cylinder areaMeasure diameter, projection, and available collar spaceFront and edge views
Latch or deadboltRecord faceplate projection and bolt reachClose-up photograph and dimension
Strike and keeperMeasure plate, keeper, screw positions, and frame depthFrame-side photograph and sketch
Panel and lever clearanceCheck projection, hand clearance, and nearby hardwareInstalled-position photographs
Door movementObserve the leaf through normal open and closed positionsFit-test note

“Lock body backset” must be measured rather than copied from a door schedule. A supplier drawing may use a different datum, such as the cylinder centre or the spindle axis. Record which reference point was used.

For a new-door order, measure the proposed leaf rather than only the old one. For a lock-only order, retain the existing leaf and frame as the baseline. When either changes later, reopen the affected gate.

Translate the catalogue record into usable fit evidence

The supplied SLK-233 record establishes the product family and management architecture, but its Door fit row contains no dimensional value. That absence is a request for evidence, not permission to assume a thickness range or standard case size.

Catalogue fieldWhat the record establishesFit question it does not settle
AccessRFID/IC card and mechanical override are listedThe physical reader, cylinder, spindle, and panel arrangement
PlatformHotel lock management software with a PC encoder and guest cardsThe door-side dimensions and mounting pattern
NetworkStandalone lock with a PC-linked card encoder and no in-room network requiredAny door geometry; network arrangement does not prove fit
FunctionsGuest card issuance, floor and room permissions, validity windows, and unlock recordsCutout sizes, edge distances, and hardware clearances
Style and finishHotel card lock style in silverPanel projection or operating clearance
Door fitThe row is recorded as —Applicable door thickness and suitable door types
DocumentationDimension drawings, installation guide, and full datasheet are available on requestWhether the released documents match the site and current SKU

Ask the supplier for the dimension drawing tied to the quoted model and finish. The request should also cover the door-side arrangement, case and backset references, spindle or fixing pattern, faceplate, latch or deadbolt, strike, panel projection, and installation clearances.

RFID card door lock fit includes the credential workflow only after the mechanical interfaces are controlled. For the card issuance, permission, validity, and recordkeeping side, see Configuring SLK-233: Credential Choices and Management Tools. Keep the physical fit record separate from that software configuration.

Resolve reverse-mount geometry before approving an order

“Reverse mount” identifies the model family, but the name alone does not tell the installer how the case, panel, spindle, or strike must be oriented on a particular door. Do not infer the mounting direction from photographs, the product name, or a supplier’s verbal description.

Request a dimensioned drawing that marks the installation orientation and all datum points. Then compare those points with the site record. The question is not whether the parts appear similar; it is whether the documented geometry closes against the measured geometry.

The same question is worked through in more detail in smart locks for server rooms. That is the same question slk 233 door fit notes has to answer here.

Fit questionEvidence requiredSite comparison
Which side carries the lock body and panel?Marked drawing with an orientation referenceCompare with the existing leaf and planned handing
Where is the case relative to the door edge?Case dimensions and defined backset datumMeasure from the same edge and reference point
How do the panel and lever project?Panel elevation and clearance notesCheck handles, frames, and adjacent walls
How does the bolt meet the strike?Latch or deadbolt and strike arrangementCompare reach, faceplate position, and keeper location
Where may fixing holes be placed?Fixing schedule or cutting templateCheck for clashes and unsupported areas
What access is needed during installation?Installation guide and service-clearance drawingCheck tool and hand access in the final position

If the drawing does not answer a question, add it to the exceptions list before requesting a fit sample. A sample can demonstrate one arrangement, but it cannot correct ambiguous instructions or settle an unrecorded dimension.

Compare the replacement decision with explicit pass conditions

Procurement should select a replacement path, not simply a preferred lock. The following decision comparison keeps site work, evidence needs, and failure conditions visible at the same time.

Replacement decisionWhat must be provenSite impactApprove when
Keep the leaf and replace the lockExisting case, spindle, cylinder, bolt, strike, and panel positions support the released drawingLowest door work, but hidden geometry may limit the choiceThe dated drawing covers the measured interface and the sample passes
Replace the leaf and retain existing lock hardwareThe new leaf reproduces every interface required by the retained hardwareFrame and leaf work, with compatibility risk at the lockThe door schedule matches the existing lock and frame evidence
Replace both leaf and lockThe complete assembly matches the door, frame, and released SLK-233 documentsHighest coordination requirement, but one controlled configurationAll components share the same revision and pass one fit record
Modify the frame or rebateThe alteration is shown on a revised drawing and accepted for the openingAdditional site work and possible schedule effectsThe revised scope is approved before alteration
Hold pending measurementsMissing geometry is named and assigned to an action ownerNo irreversible commitmentEvidence arrives and the comparison is rerun

Give the criteria project weights before reviewing supplier responses. Possible criteria include retained hardware, site disruption, installation access, credential workflow, and fit certainty. Record the reason for each weight so another reviewer can reproduce the decision.

Do not allow convenience features to compensate for missing dimensions. A proposed configuration that cannot be reconciled with the opening belongs in the hold column until the evidence is complete.

Test a controlled fit sample against the recorded opening

A fit sample should verify the released configuration, not merely demonstrate that a lock can be attached to a demonstration board. Use the same supplier drawing revision and finish configuration intended for the project.

  1. Mark the sample door edge, panel side, fixing locations, spindle reference, and strike position against the site sketch.
  2. Compare the sample faceplate and case position with the measured door edge, rebate, and lock pocket.
  3. Open and close the leaf through its normal movement range, watching for binding at the case, spindle, latch, or deadbolt.
  4. Check the panel and lever against nearby frames, walls, closers, hold-open devices, and other operating hardware.
  5. Confirm that the intended latch or deadbolt engages the strike without forcing the door.
  6. Test the approved access and emergency procedures, then inspect for loose movement or surface damage.
  7. Photograph the completed fit and attach the drawing revision to the record.

A failed sample is useful when it identifies the cause of the conflict. Mark the interfering area, return it to the supplier or installer for review, and reopen the relevant evidence gate.

Assemble the fit-note package the supplier can quote

The supplier needs one controlled package rather than scattered photographs and chat messages. Each drawing should carry a revision, and every site photograph should identify its opening number.

Package componentRequired contentAcceptance check
Opening scheduleUnique ID, location, replacement path, and quantity by typeEvery ordered opening is represented
Dimensioned site sketchLeaf, frame, rebate, case, spindle, strike, and hardware referencesDimensions use stated datums and units
Site photographsOverall view plus close-ups of each measurementOpening ID is visible or separately labelled
Existing hardware recordCase, faceplate, spindle, cylinder, latch or deadbolt, strike, and leverData is observed, not assumed from a schedule
Door and frame dataThickness, width, height, rebate, frame depth, and movementMeasurements agree with the sketch
Requested SLK-233 documentsDimension drawing, installation guide, full datasheet, and current revisionModel and finish match the intended order
Exception listUnresolved conflicts, assumptions, and required responsesEach item has an owner and disposition
Approval recordFit sample result and signed releaseApproval names the drawing revision

Use the broader commercial checklist in SLK-233 Order Checklist for Project and Repeat Purchases after the mechanical fit has been released. That keeps the fit decision distinct from order quantities, packaging, branding, manuals, and other commercial instructions.

Do not replace the fit sheet with a general door schedule. The supplier needs the measured exceptions, not only the nominal opening type.

Hand the approved fit to installation and acceptance

Create a release that tells the installer which drawing, sample, and site measurements govern the work. If any component changes after release, mark the release as superseded rather than adding notes informally.

Handoff pointInstaller checkRecord
Before workOpening ID, revision, hardware schedule, and site conditions match the releasePre-install checklist
Lock case placementCase and fixing pattern follow the released drawingInstallation photograph
Spindle and cylinderFixing components and cylinder projection match the approved arrangementClose-up photograph
Strike engagementBolt reaches the strike and operates without forcingFunctional test note
Door movementLeaf closes, latches, and operates without bindingMovement observation
Other hardwareLever, closer, hold-open, and adjacent devices do not interfereClearance photograph
Access procedureApproved credential and mechanical override procedures are testedCommissioning record
CloseoutAs-built differences are accepted or assigned for correctionSigned completion record

The catalogue records RFID/IC card access, a mechanical override, guest card issuance, permissions, validity windows, and unlock records.

Work through two illustrative replacement scenarios

These scenarios show how the gates change with the replacement boundary. They are planning examples, not completed installations or customer references.

Scenario A: replacing a door leaf and changing the lock together

The measured frame opening appears unchanged, but the proposed leaf has a different rebate and fixing arrangement. The old door dimensions cannot be copied to the new order. The project team measures the frame and the proposed leaf, obtains the SLK-233 drawing, and compares the case, panel, spindle, and strike references. Approval occurs only after a sample passes against the combined configuration. The resulting approval identifies one drawing revision for both the leaf and lock.

For the measurement side of this, see commercial smart lock application selection. That is the same question slk 233 door fit notes has to answer here.

Scenario B: replacing only the lock in an existing hotel door

The leaf and frame remain, so the opening schedule cannot describe the existing lock geometry. The team measures the case, lock body backset, fixing pattern, cylinder area, bolt, strike, and panel clearance. The supplier drawing is checked against those values, and a sample is fitted without modifying the frame. If the released drawing leaves any interface unclear, the order remains on hold even though the physical sample appears to close correctly.

Catch the fit issues that cause late substitutions

Most substitutions begin as small inconsistencies in the record. Treating each as a named exception makes them visible before they become an order change.

Common issueWhy it causes a problemPreventive control
Measuring the leaf but not the frameThe lock must relate to both the door edge and the frameRecord rebate, frame depth, keeper, and strike position
Using an old product photographThe image may not match the current drawing or revisionRequire a dated, dimensioned drawing
Assuming reverse-mount orientationSimilar appearance does not establish mounting directionMark orientation on the supplier drawing
Ignoring panel and lever projectionHardware may clash outside the lock caseRecord installed clearance and adjacent hardware
Treating a catalogue dash as a yes or noA missing field is not a dimensional approvalRequest the missing evidence explicitly
Sampling only one openingSite variation may remain hiddenSample each distinct geometry and record exceptions
Approving before closing the revisionInstallation may use obsolete dimensionsFreeze and sign the governing revision
Relying on a verbal supplier noteVerbal guidance is hard to audit or repeatConvert the response into a written exception disposition
Changing the leaf after approvalThe original fit comparison becomes invalidReopen the relevant measurement and sample gates

Keep failed and unresolved checks in the final file. They explain why a drawing or product option was rejected and prevent another reviewer from reopening the same uncertainty without context.

Record the go, conditional go, or hold decision

A fit decision should be compact enough to use during procurement review but complete enough to reconstruct the evidence behind it. Use a status that reflects the actual state of the file.

StatusMinimum basisRequired wording
GoCurrent drawing, complete site record, successful sample, and closed exceptionsName the approved model, finish, drawing revision, and approved opening types
Conditional goAll essential fit elements pass, with a bounded non-fit action still openName the action, owner, due point, and effect if it fails
HoldA dimension, orientation, interface, or revision is unresolvedState the missing evidence and which stage must reopen
RejectThe released geometry conflicts with the site or the required replacement pathRecord the failed fit evidence and the next viable option

The record should be signed by the procurement owner, the person who verified the measurements, the installer or site reviewer, and the supplier contact responsible for the released documents. One signatory may cover more than one role, but the responsibilities must still be visible.

Attach the final measurement sheet, drawing, sample photographs, exception dispositions, and approval record. Then freeze the fit package used for the commercial request. Any later change should create a new revision rather than silently altering the approved file.

Send the fit-led request for samples and a quote

Once the fit package is stable, use the request-a-quote page to submit the model, finish, drawing revision, opening quantities, required documents, and approved exceptions. Where physical verification is still required, coordinate an evaluation through the order-samples page.

A fit-led request gives the supplier a precise configuration to respond to. It also leaves a clear audit trail showing which door and lock evidence was accepted, which sample passed, and which unresolved points delayed approval.

Ваша корзина
Ваш опыт использования этого сайта будет улучшен, если вы разрешите использование файлов cookie Политика использования файлов cookie
Chat on WhatsApp