Replacing Doors or Locks with SLK-233: A Fit Checklist
Replacing a door or a lock can look like a hardware decision until the site measurements arrive. These slk 233 door fit notes turn the work into a sequence of evidence gates: identify what is changing, measure the opening, obtain current drawings, reconcile differences, and approve the fit before ordering.
Direct answer. In brief, this article covers slk 233 door fit notes from slk 233 door fit notes to slk-233. It states what to confirm about slk 233 door fit notes on the dated product page where a figure is involved. A slk 233 door fit notes treats one component on its own terms. slk 233 door fit notes names the tests that close it. slk 233 door fit notes is not accepted on a headline figure.
On slk 233 door fit notes, this article uses slk 233 door fit notes as the definition. It treats slk 233 door fit notes as a working definition specific to this market and product, rather than a general one.
- Verify the function — confirm on the dated product page for the specific SKU behind slk 233 door fit notes
- Verify the boundary — record where the technology in slk-233 stops working
- Verify the backup — name the mechanical path that remains if slk 233 door fit notes fails
- Treat this as the slk 233 door fit notes sequence, with slk 233 as the reference.
The catalogue record identifies the SLK-233 as a reverse-mount RFID card door lock in a hotel card lock style. Its published Door fit field is recorded as —, so it does not supply an applicable door thickness, door type, or dimensional drawing for procurement use. The record must be expanded through dated drawings and site measurements rather than inference.
This document is therefore a process for deciding what to replace and how to prove compatibility. It does not replace the supplier drawing, an installer’s site check, or a controlled fit sample.
Set the replacement boundary before the measurements start
Assign every affected opening a unique identification number. Record the room or opening reference, door type, existing lock type, frame description, and the reason for replacement in one line. If several openings appear identical, measure each one; the label “same door type” is not evidence that dimensions and hardware positions match.
The replacement boundary must also distinguish a planned product choice from a still-open selection. The catalogue lists RFID/IC card access and a mechanical override for the SLK-233, together with hotel lock management software, a PC-linked card encoder, guest cards, floor and room permissions, check-in validity windows, and unlock records. Confirm on the dated product page for the specific SKU before relying on any of those fields for procurement. The comparison the same buyer runs first is SLK-9905A Procurement Checklist for Hotel Projects.
Use the published specification as a starting point, not as a fit approval. The companion article SLK-233: Reading the Published Specification Without Guesswork explains which recorded fields can answer a question and which fields require dated evidence from the supplier.
Capture the decision owner
The fit file should identify one person responsible for site records, one person responsible for supplier documentation, and the installer or site reviewer who will perform the final comparison. A procurement manager can coordinate these records without turning the estimate into an unverified dimensional claim.
If another lock model is still under consideration, keep it in a separate option column. Do not allow features from the alternative model to fill gaps in the SLK-233 record.
Use a gated sequence instead of a single approval request
The order of work matters because a drawing requested before the opening is measured can only answer part of the question. Likewise, a sample checked before the drawing revision is fixed may test the wrong version.
flowchart TD
A[Record opening and scope] --> B[Measure door and frame]
B --> C[Obtain dated SLK-233 documents]
C --> D{Fit data covers the site geometry?}
D -->|Yes| E[Build controlled fit sample]
D -->|No| F[Hold and close the evidence gap]
E --> G{Physical fit passes?}
G -->|Yes| H[Release procurement approval]
G -->|No| F
F --> C
| Stage | Work at this stage | Output | Gate to the next stage |
|---|---|---|---|
| Scope | Define the opening and replacement boundary | Opening schedule | A named decision owner accepts the scope |
| Measure | Record door, frame, case, latch, strike, and hardware geometry | Site measurement sheet | Required fields are complete |
| Document | Request current drawings, guide, and datasheet | Supplier evidence pack | Drawings match the quoted SKU |
| Reconcile | Compare supplier geometry with site records | Exceptions list | Every conflict has a resolution |
| Sample | Check a controlled sample against the opening | Fit-test record | Mechanical operation and clearance pass |
| Approve | Freeze the drawing and commercial configuration | Signed fit decision | Procurement may release the order |
A stage is complete only when its output exists in the project record. A verbal assurance, an unlabeled photograph, or an undated sketch should not close a gate.
Decide whether the door, lock, or both are changing
Begin by stating what the project actually replaces. Changing the lock preserves the door leaf, frame, rebate, and most fixed hardware. Replacing the leaf may change thickness, rebate geometry, fixing positions, and clearance relationships even if the opening width is unchanged. A hotel door retrofit can also combine either path with changed access-control requirements.
Treat the slk 233 door fit notes as separate work packages for each case. This prevents the dimensions of a replacement door from being copied into a lock-only estimate or the case of an existing lock from being carried into a new-door order.
| Replacement path | What must be measured | Main fit risk | Required proof |
|---|---|---|---|
| Lock only | Existing case, backset, spindle, cylinder, latch or bolt, strike, and panel position | The new lock cannot occupy the recorded case or reach the existing strike | Supplier drawing compared with site measurements and a fit sample |
| Door leaf only | Leaf thickness, rebate, fixing points, and required hardware positions | The supplied leaf differs from the frame or the existing lock interface | Door schedule, dimensioned sketch, and supplier confirmation against that schedule |
| Door leaf and lock | Both existing geometry and the complete new interface | Errors in either scope can cancel the other | One combined fit record covering the final assembly |
| Frame or rebate modification | Existing frame condition and the exact alteration proposed | Work expands beyond the original replacement scope | Revised drawings and site approval before alteration |
Do not use this checklist as approval for an opening with special fire-rating, emergency-egress, or life-safety constraints. The project record must identify the relevant reviewer and the evidence required for that opening.
CONFIRM-WITH-LOCAL-FIRE-AND-EGRESS-REVIEW
Build the door measurement checklist without guesswork
A useful door measurement checklist records the actual opening rather than a catalogue label. Use the same units throughout, identify the measurement point, and attach a scaled photograph showing where the tape or calliper was placed. Record nominal frame information separately from measured site information.
| Item | Site method | Evidence to retain |
|---|---|---|
| Door leaf thickness | Measure at the lock position and away from hardware | Dimension, location, and photograph |
| Leaf width and height | Measure the leaf itself, not only the frame opening | Overall dimension sketch |
| Frame opening and rebate | Record width, depth, and rebate dimensions at the lock area | Section sketch with dimensions |
| Lock case pocket | Measure length, width, and depth of the opening in the leaf | Marked photograph |
| Faceplate area | Measure plate width and height plus fixing positions | Direct outline or sketch |
| Lock body backset | Measure from the door edge to the spindle or cylinder reference | Dimensioned edge view |
| Spindle and fixing pattern | Record square section, centres, and fixing locations | Photograph and dimension drawing |
| Cylinder area | Measure diameter, projection, and available collar space | Front and edge views |
| Latch or deadbolt | Record faceplate projection and bolt reach | Close-up photograph and dimension |
| Strike and keeper | Measure plate, keeper, screw positions, and frame depth | Frame-side photograph and sketch |
| Panel and lever clearance | Check projection, hand clearance, and nearby hardware | Installed-position photographs |
| Door movement | Observe the leaf through normal open and closed positions | Fit-test note |
“Lock body backset” must be measured rather than copied from a door schedule. A supplier drawing may use a different datum, such as the cylinder centre or the spindle axis. Record which reference point was used.
For a new-door order, measure the proposed leaf rather than only the old one. For a lock-only order, retain the existing leaf and frame as the baseline. When either changes later, reopen the affected gate.
Translate the catalogue record into usable fit evidence
The supplied SLK-233 record establishes the product family and management architecture, but its Door fit row contains no dimensional value. That absence is a request for evidence, not permission to assume a thickness range or standard case size.
| Catalogue field | What the record establishes | Fit question it does not settle |
|---|---|---|
| Access | RFID/IC card and mechanical override are listed | The physical reader, cylinder, spindle, and panel arrangement |
| Platform | Hotel lock management software with a PC encoder and guest cards | The door-side dimensions and mounting pattern |
| Network | Standalone lock with a PC-linked card encoder and no in-room network required | Any door geometry; network arrangement does not prove fit |
| Functions | Guest card issuance, floor and room permissions, validity windows, and unlock records | Cutout sizes, edge distances, and hardware clearances |
| Style and finish | Hotel card lock style in silver | Panel projection or operating clearance |
| Door fit | The row is recorded as — | Applicable door thickness and suitable door types |
| Documentation | Dimension drawings, installation guide, and full datasheet are available on request | Whether the released documents match the site and current SKU |
Ask the supplier for the dimension drawing tied to the quoted model and finish. The request should also cover the door-side arrangement, case and backset references, spindle or fixing pattern, faceplate, latch or deadbolt, strike, panel projection, and installation clearances.
RFID card door lock fit includes the credential workflow only after the mechanical interfaces are controlled. For the card issuance, permission, validity, and recordkeeping side, see Configuring SLK-233: Credential Choices and Management Tools. Keep the physical fit record separate from that software configuration.
Resolve reverse-mount geometry before approving an order
“Reverse mount” identifies the model family, but the name alone does not tell the installer how the case, panel, spindle, or strike must be oriented on a particular door. Do not infer the mounting direction from photographs, the product name, or a supplier’s verbal description.
Request a dimensioned drawing that marks the installation orientation and all datum points. Then compare those points with the site record. The question is not whether the parts appear similar; it is whether the documented geometry closes against the measured geometry.
The same question is worked through in more detail in smart locks for server rooms. That is the same question slk 233 door fit notes has to answer here.
| Fit question | Evidence required | Site comparison |
|---|---|---|
| Which side carries the lock body and panel? | Marked drawing with an orientation reference | Compare with the existing leaf and planned handing |
| Where is the case relative to the door edge? | Case dimensions and defined backset datum | Measure from the same edge and reference point |
| How do the panel and lever project? | Panel elevation and clearance notes | Check handles, frames, and adjacent walls |
| How does the bolt meet the strike? | Latch or deadbolt and strike arrangement | Compare reach, faceplate position, and keeper location |
| Where may fixing holes be placed? | Fixing schedule or cutting template | Check for clashes and unsupported areas |
| What access is needed during installation? | Installation guide and service-clearance drawing | Check tool and hand access in the final position |
If the drawing does not answer a question, add it to the exceptions list before requesting a fit sample. A sample can demonstrate one arrangement, but it cannot correct ambiguous instructions or settle an unrecorded dimension.
Compare the replacement decision with explicit pass conditions
Procurement should select a replacement path, not simply a preferred lock. The following decision comparison keeps site work, evidence needs, and failure conditions visible at the same time.
| Replacement decision | What must be proven | Site impact | Approve when |
|---|---|---|---|
| Keep the leaf and replace the lock | Existing case, spindle, cylinder, bolt, strike, and panel positions support the released drawing | Lowest door work, but hidden geometry may limit the choice | The dated drawing covers the measured interface and the sample passes |
| Replace the leaf and retain existing lock hardware | The new leaf reproduces every interface required by the retained hardware | Frame and leaf work, with compatibility risk at the lock | The door schedule matches the existing lock and frame evidence |
| Replace both leaf and lock | The complete assembly matches the door, frame, and released SLK-233 documents | Highest coordination requirement, but one controlled configuration | All components share the same revision and pass one fit record |
| Modify the frame or rebate | The alteration is shown on a revised drawing and accepted for the opening | Additional site work and possible schedule effects | The revised scope is approved before alteration |
| Hold pending measurements | Missing geometry is named and assigned to an action owner | No irreversible commitment | Evidence arrives and the comparison is rerun |
Give the criteria project weights before reviewing supplier responses. Possible criteria include retained hardware, site disruption, installation access, credential workflow, and fit certainty. Record the reason for each weight so another reviewer can reproduce the decision.
Do not allow convenience features to compensate for missing dimensions. A proposed configuration that cannot be reconciled with the opening belongs in the hold column until the evidence is complete.
Test a controlled fit sample against the recorded opening
A fit sample should verify the released configuration, not merely demonstrate that a lock can be attached to a demonstration board. Use the same supplier drawing revision and finish configuration intended for the project.
- Mark the sample door edge, panel side, fixing locations, spindle reference, and strike position against the site sketch.
- Compare the sample faceplate and case position with the measured door edge, rebate, and lock pocket.
- Open and close the leaf through its normal movement range, watching for binding at the case, spindle, latch, or deadbolt.
- Check the panel and lever against nearby frames, walls, closers, hold-open devices, and other operating hardware.
- Confirm that the intended latch or deadbolt engages the strike without forcing the door.
- Test the approved access and emergency procedures, then inspect for loose movement or surface damage.
- Photograph the completed fit and attach the drawing revision to the record.
A failed sample is useful when it identifies the cause of the conflict. Mark the interfering area, return it to the supplier or installer for review, and reopen the relevant evidence gate.
Assemble the fit-note package the supplier can quote
The supplier needs one controlled package rather than scattered photographs and chat messages. Each drawing should carry a revision, and every site photograph should identify its opening number.
| Package component | Required content | Acceptance check |
|---|---|---|
| Opening schedule | Unique ID, location, replacement path, and quantity by type | Every ordered opening is represented |
| Dimensioned site sketch | Leaf, frame, rebate, case, spindle, strike, and hardware references | Dimensions use stated datums and units |
| Site photographs | Overall view plus close-ups of each measurement | Opening ID is visible or separately labelled |
| Existing hardware record | Case, faceplate, spindle, cylinder, latch or deadbolt, strike, and lever | Data is observed, not assumed from a schedule |
| Door and frame data | Thickness, width, height, rebate, frame depth, and movement | Measurements agree with the sketch |
| Requested SLK-233 documents | Dimension drawing, installation guide, full datasheet, and current revision | Model and finish match the intended order |
| Exception list | Unresolved conflicts, assumptions, and required responses | Each item has an owner and disposition |
| Approval record | Fit sample result and signed release | Approval names the drawing revision |
Use the broader commercial checklist in SLK-233 Order Checklist for Project and Repeat Purchases after the mechanical fit has been released. That keeps the fit decision distinct from order quantities, packaging, branding, manuals, and other commercial instructions.
Do not replace the fit sheet with a general door schedule. The supplier needs the measured exceptions, not only the nominal opening type.
Hand the approved fit to installation and acceptance
Create a release that tells the installer which drawing, sample, and site measurements govern the work. If any component changes after release, mark the release as superseded rather than adding notes informally.
| Handoff point | Installer check | Record |
|---|---|---|
| Before work | Opening ID, revision, hardware schedule, and site conditions match the release | Pre-install checklist |
| Lock case placement | Case and fixing pattern follow the released drawing | Installation photograph |
| Spindle and cylinder | Fixing components and cylinder projection match the approved arrangement | Close-up photograph |
| Strike engagement | Bolt reaches the strike and operates without forcing | Functional test note |
| Door movement | Leaf closes, latches, and operates without binding | Movement observation |
| Other hardware | Lever, closer, hold-open, and adjacent devices do not interfere | Clearance photograph |
| Access procedure | Approved credential and mechanical override procedures are tested | Commissioning record |
| Closeout | As-built differences are accepted or assigned for correction | Signed completion record |
The catalogue records RFID/IC card access, a mechanical override, guest card issuance, permissions, validity windows, and unlock records.
Work through two illustrative replacement scenarios
These scenarios show how the gates change with the replacement boundary. They are planning examples, not completed installations or customer references.
Scenario A: replacing a door leaf and changing the lock together
The measured frame opening appears unchanged, but the proposed leaf has a different rebate and fixing arrangement. The old door dimensions cannot be copied to the new order. The project team measures the frame and the proposed leaf, obtains the SLK-233 drawing, and compares the case, panel, spindle, and strike references. Approval occurs only after a sample passes against the combined configuration. The resulting approval identifies one drawing revision for both the leaf and lock.
For the measurement side of this, see commercial smart lock application selection. That is the same question slk 233 door fit notes has to answer here.
Scenario B: replacing only the lock in an existing hotel door
The leaf and frame remain, so the opening schedule cannot describe the existing lock geometry. The team measures the case, lock body backset, fixing pattern, cylinder area, bolt, strike, and panel clearance. The supplier drawing is checked against those values, and a sample is fitted without modifying the frame. If the released drawing leaves any interface unclear, the order remains on hold even though the physical sample appears to close correctly.
Catch the fit issues that cause late substitutions
Most substitutions begin as small inconsistencies in the record. Treating each as a named exception makes them visible before they become an order change.
| Common issue | Why it causes a problem | Preventive control |
|---|---|---|
| Measuring the leaf but not the frame | The lock must relate to both the door edge and the frame | Record rebate, frame depth, keeper, and strike position |
| Using an old product photograph | The image may not match the current drawing or revision | Require a dated, dimensioned drawing |
| Assuming reverse-mount orientation | Similar appearance does not establish mounting direction | Mark orientation on the supplier drawing |
| Ignoring panel and lever projection | Hardware may clash outside the lock case | Record installed clearance and adjacent hardware |
| Treating a catalogue dash as a yes or no | A missing field is not a dimensional approval | Request the missing evidence explicitly |
| Sampling only one opening | Site variation may remain hidden | Sample each distinct geometry and record exceptions |
| Approving before closing the revision | Installation may use obsolete dimensions | Freeze and sign the governing revision |
| Relying on a verbal supplier note | Verbal guidance is hard to audit or repeat | Convert the response into a written exception disposition |
| Changing the leaf after approval | The original fit comparison becomes invalid | Reopen the relevant measurement and sample gates |
Keep failed and unresolved checks in the final file. They explain why a drawing or product option was rejected and prevent another reviewer from reopening the same uncertainty without context.
Record the go, conditional go, or hold decision
A fit decision should be compact enough to use during procurement review but complete enough to reconstruct the evidence behind it. Use a status that reflects the actual state of the file.
| Status | Minimum basis | Required wording |
|---|---|---|
| Go | Current drawing, complete site record, successful sample, and closed exceptions | Name the approved model, finish, drawing revision, and approved opening types |
| Conditional go | All essential fit elements pass, with a bounded non-fit action still open | Name the action, owner, due point, and effect if it fails |
| Hold | A dimension, orientation, interface, or revision is unresolved | State the missing evidence and which stage must reopen |
| Reject | The released geometry conflicts with the site or the required replacement path | Record the failed fit evidence and the next viable option |
The record should be signed by the procurement owner, the person who verified the measurements, the installer or site reviewer, and the supplier contact responsible for the released documents. One signatory may cover more than one role, but the responsibilities must still be visible.
Attach the final measurement sheet, drawing, sample photographs, exception dispositions, and approval record. Then freeze the fit package used for the commercial request. Any later change should create a new revision rather than silently altering the approved file.
Send the fit-led request for samples and a quote
Once the fit package is stable, use the request-a-quote page to submit the model, finish, drawing revision, opening quantities, required documents, and approved exceptions. Where physical verification is still required, coordinate an evaluation through the order-samples page.
A fit-led request gives the supplier a precise configuration to respond to. It also leaves a clear audit trail showing which door and lock evidence was accepted, which sample passed, and which unresolved points delayed approval.

