Door mounting interface datasheet claims: turn supplier mounting claims into a measurable qualification checklist for door thickness, mortise.

Publicado em: jul 23, 2026

Reading the Door Mounting Interface Claims in a Supplier Datasheet

Reading the Door Mounting Interface Claims in a Supplier Datasheet

A system integrator receives a clean-looking lock specification, but the mounting details may still conceal a mismatch. A supplier says the unit fits most timber doors, uses a standard backset, or is easy to retrofit; the lock body, door rebate, strike box and spindle position may still disagree. Treat door mounting interface datasheet claims as questions with evidence, not as installation instructions.

Direct answer. Short version — door mounting interface datasheet claims is treated here as door mounting interface datasheet claims first. door-mounting-interface comes second. The evidence for door mounting interface datasheet claims is named in the sections below. A door mounting interface datasheet claims is a component behaviour guide. It covers limits. It covers failure modes. door mounting interface datasheet claims decides whether door mounting interface datasheet claims is acceptable for this build.

This article defines door mounting interface datasheet claims through door mounting interface datasheet claims. The definition of door mounting interface datasheet claims is deliberately narrow. It is non-statutory, and it applies to the market and product being discussed.

  • Establish the reach — confirm on the dated product page for the specific SKU behind door mounting interface datasheet claims
  • Establish the edge — record where the technology in door-mounting-interface stops working
  • Establish the reserve — name the mechanical path that remains if door mounting interface datasheet claims fails
  • For door mounting interface datasheet claims, the order below is fixed and door mounting interface is the reference point.

Before a candidate reaches the approved-vendor list, translate every mounting statement into a measurable interface: door leaf and frame, lock body or mortise, panel opening, latch or deadbolt, backset, spindle, strike and fastening. Then ask for dated evidence against the actual opening. This tear-off checklist keeps quotation-stage review separate from site survey work and makes unresolved items visible before purchase.

Normalize each statement into a closable claim

Preserve the supplier’s wording in the record, but add four fields beside it: component, operating condition, dimension or tolerance, and evidence. “Standard backset,” for example, becomes “backset from the spindle centre to the lock-body edge equals the proposed measurement; provide the drawing.”

Supplier statementRewrite before approvalRequired close-out
“Suitable for a stated thickness”Identify which door thickness is measured and which tolerance appliesControlled drawing plus opening measurement
“Standard mortise”Name the lock body, pocket dimensions and fixing patternDimensioned section and door-edge check
“Fits most doors”List included and excluded door constructionsFit envelope and sample result
“Easy installation”State required tools, preparation and site accessInstallation guide and preparation list
“No special hardware”Identify every included and separately supplied itemFastener schedule and accessory list
  • The claim names one physical component.
  • The applicable condition and dimension are explicit.
  • The evidence has an owner and an expected date.
  • “Compatible,” “standard” and “universal” have been replaced by measurable terms.

Pull the interface onto one controlled drawing

Request dimension drawings rather than a cropped installation image. The set should identify the drawing number, revision, date, units, viewing direction and datum. Ask for a door section and installation template that show how the lock body, panel and strike occupy the same opening.

  • Door leaf and frame dimensions appear together.
  • Door swing and handing are identified.
  • Lock-body pocket, fixing centres and clearances are dimensioned.
  • Latch or deadbolt, strike and keeper relationship is sectioned.
  • Fasteners and separately supplied accessories are listed.

A drawing without revision control is only a visual reference. Record the file or document identifier with the quote so that later samples and site measurements point to the same issue.

flowchart TD
    A[Receive mounting claim] --> B[Normalize claim]
    B --> C[Request controlled evidence]
    C --> D[Measure or inspect candidate]
    D --> E{All close-out fields met}
    E -->|Yes| F[Release candidate]
    E -->|No| G[Record deviation]

Check thickness without calling it compatibility

The applicable door thickness field may describe only the leaf. Confirm whether the supplier includes a fixed rebate, seal, closer or other attached item in that range. Measure the proposed opening at the latch, middle and hinge positions, then compare the measurements with the stated range and drawing tolerance.

The published SLK-9936S hotel-lock fact block states 36–100 mm door thickness and also identifies a 5-pin cylinder and 3-point latch. Those are useful anchors, not a substitute for the interface drawing. Confirm on the dated product page for the specific SKU and obtain the controlled dimension drawing before accepting the candidate.

  • Thickness is measured at three leaf positions.
  • The measurement method and tolerance are recorded.
  • Existing rebates, seals and closers are visible on the survey.
  • The proposed door construction remains within the written envelope.

Use the Office Smart Lock Site Survey as a site-record companion, then resolve any mismatch before the lock is specified.

Match the lock body and mortise as one dimensional

Treat the lock body and mortise as a dimensional pair rather than a product-family label. Confirm pocket width, height, depth, backset and fixing centres against the actual door or a representative sample. Also record the distance from the spindle centre to the lock-body edge.

Backset and spindle position determine how the panel, handle or lever and lock case meet. Confirm spindle length and profile, cylinder or rose position, and the clearance needed to fit the panel and operate the mechanism. Do not scale a drawing from a catalogue image.

  • Door-edge reference is defined.
  • Lock-body or mortise pocket dimensions match.
  • Backset and spindle geometry match.
  • Panel and rose clearance are shown.
  • Handle or lever operation is demonstrated.

Verify latch, strike and fastening as one movement

Ask how the latch or deadbolt enters the strike, how the strike plate sits against the frame face, and how the keeper or strike box relates to the door rebate. A correct lock-body width can still produce a binding or misaligned latch if these adjoining parts are not coordinated.

Check the mounting hardware schedule, including fixing positions, screw access and any adaptor supplied for the opening. If a door closer or hold-open device is present, include its body and swing in the same drawing. An illustrative retrofit may keep an existing strike box while replacing the leaf; that is a deviation to verify, not a reason to assume a universal fit.

  • Latch projection and bolt travel are stated.
  • Strike plate and keeper dimensions are supplied.
  • Fasteners reach sound material at the listed points.
  • Closer or hold-open interaction is shown.
  • The sample operates without forced alignment.

Keep power, wiring and service access visible

A mounting review should also locate the battery or cell compartment, emergency power port, cable route and service-removal clearance. Ask whether the control PCB and any wireless module remain accessible after the escutcheon is fitted, without requiring the door leaf or frame to be reopened.

  • Battery or cell access is reachable after installation.
  • Emergency power access does not conflict with the panel.
  • Cable entry is shown within the allowed rebate.
  • Component service boundaries are identified.

Treat electrical access as part of the interface drawing, not as a late installation surprise.

Grade the evidence in a fixed order

Use descending evidence strength: controlled dimension drawings; the installation guide; dated product documentation; a marked sample; and finally a descriptive supplier statement. A newer document does not automatically override a newer physical sample, so record both when they differ.

  • Every drawing has an identifier, revision and date.
  • Every product fact points to the specific SKU.
  • Each close-out claim maps to one document or observation.
  • Conflicts are recorded as deviations rather than averaged values.

The Door Mounting Interface Test Evidence a Buyer Can Actually Request sets out the evidence hierarchy in more detail. If an answer is still generic, review The Door Mounting Interface Failure Modes Seen on Smart Lock Projects and ask which failure the missing field could conceal.

Compare answers before choosing a vendor

A technically plausible answer is not the same as a released interface. Use the decision table below at qualification, then repeat it against the final quotation revision.

Decision pointAcceptHoldAsk again
Door thicknessRange, method and drawing agreeOnly a nominal number is suppliedObtain measured opening and tolerance
Body and spindlePocket, backset and spindle are dimensioned“Standard” is the only descriptionRequest marked section drawing
Latch and strikeAlignment and fixing schedule are shownComponents are shown separatelyRequest a coordinated interface drawing
Evidence trailRevision, SKU and observation matchDocuments have different datesReconfirm the controlling revision

The close-out record for door mounting interface datasheet claims should show who supplied each answer, which evidence closed it and whether a site survey remains. Use this door fit verification worksheet as a binary release tool: any hold item blocks release until closed or formally accepted by the project team.

Record exceptions as deviations, not adjectives

For every unresolved field, capture the claim, source, affected door, discrepancy, owner, corrective action and disposition. Attach the relevant drawing revision and measurement record. Use one door-mounting-interface record to connect the claim, evidence and outcome across quotations and samples.

  • No exception is labeled only “check later.”
  • The affected door or door type is identified.
  • The corrective evidence is attached.
  • The responsible party accepts the residual condition.
  • The approved drawing revision is recorded.

To connect interface decisions with service exposure, compare the open items with How the Door Mounting Interface Drives Smart Lock Reliability. This keeps a qualification exception visible beyond the purchase order.

Apply the qualification release gate

Release the candidate only when every critical dimension has a controlling revision, all deviations have a disposition, and the evidence package identifies the exact candidate. Keep the candidate on hold if any drawing is missing, any measurement conflicts with the written range, or a supplied accessory remains unallocated.

The practical counterpart to this point is fingerprint smart locks for facility managers. That is the same question door mounting interface datasheet claims has to answer here.

  • Controlled drawings are attached and current.
  • Door measurements or survey data support the range.
  • Lock body, spindle, latch and strike agree.
  • Power and service access are shown.
  • All deviations are closed or formally accepted.
  • The evidence package names the exact candidate.

CONFIRM-WITH-LOCAL-AUTHORITY: Confirm all site-specific safety and approval requirements for the opening with the relevant authority and the door supplier.

This checklist supports technical qualification; it does not replace the dated product record or a project-specific survey.

Send one consolidated request

A supplier can answer faster when the request arrives as one package. Include the door type, representative dimensions, leaf and frame construction, handing, closer arrangement, desired panel position and the commercial reference. Then ask for the current drawings and a response against each field.

  1. Which dimension drawing controls this candidate?
  2. Is applicable door thickness measured on the leaf or the assembled opening?
  3. What are the lock-body or mortise pocket dimensions and tolerances?
  4. Which backset and spindle geometry are required?
  5. Which latch, strike plate and keeper are included?
  6. Which mounting hardware and adaptors are supplied?
  7. Which document confirms power-port and service-access locations?

For the final site check, combine this list with The Door Mounting Interface and Door Compatibility: The Fit Envelope and the Smart Lock Retrofit Site Survey.

Use the factory’s Request Catalog route to obtain the controlled document set, then send the measured opening and completed close-out list with a Request a Quote.

O seu carrinho
A sua experiência neste site será melhorada se permitir cookies Política de cookies
Chat on WhatsApp