Nothing that fits a framed door or a wooden door fits a frameless one without checking the edge first. Frameless is not a style detail.

Pubblicato il: apr 10, 2024

What Smart Lock Is Best for Frameless Glass Doors?

What Smart Lock Is Best for Frameless Glass Doors?

Short answer: for a frameless glass door, the best smart lock is a glass-door-specific unit whose mounting architecture matches how the panel is already hung — a clamp-on or patch-adjacent body for retrofit tempered panels that must not be drilled, or a drilled-mount body only when hole positions were specified into the panel before tempering — and whose published fit envelope covers your measured glass thickness and edge condition. Nothing that fits a framed door or a wooden door fits a frameless one without checking the edge first.

Frameless is not a style detail. It is a structural constraint. A framed glass door lets hardware borrow strength from the aluminum or uPVC surround; a frameless tempered panel has to carry every gram of lock, handle and strike on its own polished edges. That single fact reorders the whole buying process.

The exchange below is an illustrative composite built from the pre-order questions this factory's glass-lock line handles weekly — it is not a transcript of any real customer conversation. Two roles repeat through it: CR, an interior contractor running a mixed storefront job, and SP, a glass-lock product specialist. After each scene, a Field note annotates what just happened and why it matters to your own quote request.

Scene 1 — The Survey Site: "What Are We Actually Locking?"

CR: Six storefront units along a retail arcade, all frameless tempered, single-leaf, swing. Plus two interior meeting-room doors, frameless, double-leaf, in a shared lobby. That's the whole scope. Catalog says you make glass locks — where do I start?

SP: Start by refusing to open the catalog. Start with the panels. For each of the eight openings I need four observations written down: how the leaf pivots, what the lock edge looks like, how thick the glass actually is, and what the fixed side offers for a strike.

CR: How it pivots — you mean hinges?

SP: On frameless work, usually patch fittings: a mortised pocket near the top of the hinge edge and another near the bottom, with a pivot pin, instead of surface hinges. Some shops hang frameless leaves on a patch-plus-floor-spring arrangement, some on a continuous patch fitting. That matters because the lock body competes for the same edge. An edge already busy with a top patch, bottom patch and pivot axis gives you one band of usable glass — typically mid-height — and every millimeter of that band has to be planned.

SP: Second observation: the lock edge itself. Polished, arrised, chipped, or drilled. If a previous installer nicked it, a clamp-on lock sits crooked no matter what you buy. Third and fourth are straightforward: actual thickness, and the receiving side.

Field note: Contractors skip this scene and pay for it later. The failure mode is not "wrong lock features" — it is "lock that cannot be mounted at all." Note the job-size discipline here too: six single-leaf storefront doors and two double-leaf interior doors are two different populations. They may well take different mounting architectures even if they come from the same catalog line. Count openings by construction type, not by total.

Scene 2 — Mounting Architecture: Patch, Hinge Side, or Clamp

CR: So the storefront doors hang on patch fittings. I have three candidate mount styles from your glass range — explain them on my door, not on a datasheet.

SP: Take the elevation apart.

FRONT ELEVATION — single-leaf frameless tempered storefront door
(illustrative geometry only; every dimension to verify in writing per project and
per product page — nothing below is a SLK-G200 specification) header / top rail ────────────────────────────────────────────────────────────── │ │ │ glass panel (tempered, no frame) │ │ │ hinge │ ┌───────────────┐ │ strike side │ │ top patch │ ← pivot pocket │ side │ │ fitting │ at leaf top │ │ └───────┬───────┘ │ │ │ │ │ ┌───────┴───────┐ ← lock zone: │ │ │ clamp-on │ usable mid- │ │ │ smart lock │ edge band │ │ │ body + turn │ │ │ └───────────────┘ │ │ │ │ │ ┌───────┴───────┐ │ │ │ bottom patch │ ← floor spring │ │ │ fitting │ or pivot │ │ └───────────────┘ │ │ │ ────────────────────────────────────────────────────────────── floor / threshold

SP: Option one: the lock shares the patch logic. Bodies that sandwich between two patch-style fittings above and below, or that bolt into a factory-provided patch-adjacent zone, load the panel the way the hinges already do. Option two: clamp-on. Two face plates — outside and inside — grip the glass with a body on each side, no holes at all. Option three: a drilled mount, where cylinder bolts or body studs pass through holes laid into the glass before it was tempered.

CR: And on my six storefront doors, all already glazed with undrilled panels —

SP: — option three is dead unless you re-order glass, and option two is the default. Patch-sharing works only where the existing patch layout and the lock's template happen to agree, which you cannot know until someone sends photos with measurements.

CR: What decides between clamp-on and patch-sharing then?

SP: Three things. Usable mid-edge band length: measure from the top patch pocket's lower edge to the bottom patch pocket's upper edge. Interference: any closer-fitting, finger pull or existing hardware inside that band. And the fixed side: a clamp lock still needs a strike anchored to a wall return, a patch strike on the adjacent fixed panel, or a floor pocket. Frameless storefronts often have none of these, and adding one is glazier work, not lockwork.

Field note: This is the frameless-specific depth that general glass-door method can't cover — see the broader glass door smart lock specification sequence for framed and mixed applications. The core annotation: on frameless tempered glass, the mount is the decision. Credentials, app behavior and finishes are downstream. A contractor who can name their mount architecture has effectively specified the product.

Mount-Architecture Decision Matrix

CriterionPatch-adjacent mountClamp-on (no-drill)Drilled mount (pre-temper holes)
Field retrofit on existing tempered panelOnly if patch layout already matches templateYes — default retrofit choiceNo — glass cannot be drilled after tempering
Load path into glassEdge zone, like existing patchesFace-to-face compression sandwichStuds/bolts through planned holes
New-glass involvementUsually noneUsually nonePanel re-ordered with hole coordinates into the tempering spec
Critical measurementPocket-to-pocket clear bandGlass thickness vs lock's supported band (to verify in writing — check the product page)Hole center-to-center and edge distances
Typical failure if wrongLock overlaps pivot pocket; no seatBand too tight; clamp over edge chamferHole pattern mismatch; panel is scrap
Best fitDoors hung fresh with lock designed inArcade/retail retrofits, landlord rulesFlagship lobbies, design-intent jobs

Scene 3 — Thickness First: Measure, Then Even Doubt Your Caliper

CR: Give me the number so I write it in the RFQ. What glass thickness does your G200 take?

SP: I will hand you the worksheet, not a number. The supported thickness band for SLK-G200 is published on its product page and must be transcribed there — and then re-checked against your panels — before any fit claim means anything. What I can teach you is the measurement, because it's where contractors leak.

CR: Eight millimeters, obviously. Everyone quotes frameless as eight.

SP: Everyone quotes nominal. Tempered architectural glass for frameless doors is commonly supplied at 8, 10 or 12 mm nominal, but actual can read 7.6 or 11.5, and clamp mechanisms care about actual. Measure three points down the lock-edge height, not one. Glass batches bow; microns of curvature shift a single-point reading.

SP: Then write the edge. Is it polished flat, pencil-arrised, or chamfered? A clamp plate on a chamfered edge compresses on one side only. And photograph any nick within 100 mm of the intended lock zone before I quote against it.

Field note: The thickness worksheet is the single most reusable artifact in this article. Fill it for every opening before you email anyone. It converts "do you have something for glass doors" (a buyer-noise question) into "here are eight openings, here are their measured values, here are the photos" (a quote-ready question). The same measurement mindset applies to wooden and metal doors — but on frameless glass there is no correction step after the panels are made, so errors are absolute.

Frameless Panel Measurement Worksheet (one row per opening)

Opening IDNominal thickness (claimed)Actual thickness @ top / mid / bottom (mm)Lock edge conditionUsable mid-edge band (mm)Patch layout: top/bottom pocket typeStrike side: wall / fixed panel / floorG200 band fits? (transcribe band from product page)
S1 — storefront 1EXAMPLE: 10 mm nominal___ / ___ / ___polished, arrised___standard patch + floor springfixed panel, 8 mmcheck vs to verify in writing band
S2 … S6
D1, D2 — lobby doubles

Blank cells are deliberate. Transcribe the supported-thickness band and clamp geometry from the SLK-G200 product page before marking any row fit / not fit.

Scene 4 — Drill vs No-Drill: The Line Tempering Draws

CR: One storefront tenant wants the body studs through the glass. Looks cleaner. Can an installer drill two holes on site?

SP: No. Tempered glass is in compression at the surface; any drill, grinder or notch past the cure breaks that balance and the panel disintegrates — sometimes instantly, sometimes minutes later during handling. There is no careful way to drill tempered glass after tempering. The on-site options are non-drill architectures: clamp-on bodies, patch-adjacent mounts, and surface-adhered strikes.

CR: So drilled mounting means…

SP: Means the panel is ordered again. You supply hole coordinates — center-to-center spacing, edge distances — matched to a lock's published template (template dimensions: to verify in writing, read from the product page), and the fabricator cuts, edges, drills, then tempers. Holes become permanent, and if the template was wrong, the glass becomes scrap. Laminated glass is a different animal — it can be drilled on site with proper tooling — but storefront frameless doors are overwhelmingly tempered, and you should not assume any panel is laminated without the glazier's confirmation.

flowchart TD
    A{Panel already tempered?} -->|Yes| B{Factory holes present and matched to a lock template?}
    A -->|Laminated - verify with glazier| C[On-site drilling possible with specialist tooling]
    B -->|Yes| D[Transcribe template values from product page; verify against existing holes before ordering]
    B -->|No| E{Design-intent job: re-order panel acceptable?}
    E -->|Yes| F[Issue hole coordinates into new tempering spec - panel + lock ordered together]
    E -->|No| G[Clamp-on or patch-adjacent no-drill architecture]
    G --> H[Verify measured thickness against to verify supported band before RFQ]
    D --> H

Field note: The annotation here is about who carries risk. No-drill: risk lives with the measurement (thickness band, edge condition) and it is all recoverable before order. Drilled: risk lives with the template handoff between lock supplier and glass fabricator, and it is unrecoverable after tempering. Most contractors on retrofit jobs should treat drilled mounting as a glazing-scope decision, not a hardware decision — if it enters your project, the glazier signs the coordinates, not the lock seller.

Scene 5 — Double Frameless Leaves: The Follower Question Nobody Asks

CR: Back to my two lobby doors. Double-leaf, both frameless, no center mullion. I put a smart lock on the left leaf. What grabs the right leaf?

SP: Two mechanisms exist and you must pick one explicitly. First: a mechanical follower. The active leaf carries the smart lock's latch case; the inactive leaf carries a follower body — essentially a latch that is driven by the active leaf's latch or retracts manually with a flush bolt — so the pair closes without a strike on both leaves. Second: lock both leaves with flush bolts top and bottom on the inactive side, and treat the active leaf's latch as the only interface.

CR: Does your glass line run the follower natively?

SP: Follower compatibility for the G200 is a product-page question, not a sales-desk question — it is verified in writing like everything else on this door. What I will say architecturally: not every clamp-on glass lock is offered in a left-hand, right-hand and follower variant set. A job with two double doors needs a coherent set: one active body per pair, one follower or flush-bolt plan per pair, and strike provisions on the fixed sides of the opening.

CR: And the gaps between leaves?

SP: Kill that question with the survey. Frameless double-leaf sets hang with a visible gap band; the latch throw has to cross it and still register. Gap and alignment expectations for these bodies deserve their own reading — the pre-order site survey template covers surveying single and double openings with photos, and the double-opening fit logic with worked examples sits in the double glass door lock fit notes. I will not let you order leaves-and-followers blind from a chat.

Field note: Doubles are where frameless orders split into "one more unit" mistakes. An order for "two G200-class sets" that mixes active bodies without followers, or ignores handed orientation per pair, becomes a site fight. The annotation for procurement: on any job with double-leaf frameless doors, the RFQ line item is a set — active body + follower/flush-bolt plan + strike — per pair, not a lock per door.

Double-Leaf Frameless Coordination Checklist

Item to resolveStorefront single (x6)Lobby double (x2 pairs)Status on this job
Active leaf designated (which side swings first)N/A___ / pairopen
Inactive leaf retention: follower vs top+bottom flush boltsN/A___to verify in writing follower availability per product page
Handed orientation ordered per leaf, not per pairLH/RH confirmed per openingLH+RH set per pairopen
Strike anchorage on fixed side (wall return / fixed panel / floor pocket)requiredrequired on both outer jambssurvey photos pending
Leaf-to-leaf gap measured at latch height, top and bottomN/A___ / ___ mmopen
Latch throw clearance vs measured gap bandcheck vs templatecheck vs template + followerafter survey

Scene 6 — Damage Risk During Install: How the Factory Side Defends the Panel

CR: Last thing before I quote this upward. If a clamp bolt cracks a tenant's panel mid-install, who made the mistake?

SP: Usually the install sequence, and the sequence is exactly what good factory guidance exists to control. Four recurring mechanisms: overtightening a clamp bolt down hard on bare glass; tightening bolts in sequence so the plates sit skewed and load one corner; gasket omission — no compliant pad between steel and glass, so point loads concentrate; and edge contact during handling, where the polished lock edge kisses concrete or a steel jamb before the body is even out of the carton.

CR: What does your guidance actually do about those?

SP: Four answers. Pad and gasket sets travel with the kit rather than being improvised from tape. The instruction sheet specifies a light-first, cross-pattern tightening sequence with a stop condition — snug and square, seated, then final quarter-turns — instead of "torque it down." A mounting template or positional jig keeps plates aligned so the clamp closes flat on both faces at once. And the pre-install check is blunt: inspect edge for nicks before the body goes on, because a clamp amplifies an existing flaw instead of hiding it.

CR: And if a panel does fail?

SP: Then the honest answer is: tempered panels under clamp load fail sometimes from causes nobody can see — a pre-existing edge flaw from the fabricator, or a building settlement that bowed the opening after glazing. That is why the sample-before-bulk path exists. Order one set, bench-fit it to a measured-thickness sample or offcut from your actual panel, run the install sheet yourself, then release the rest of the job. On a mixed job like yours — six singles and two doubles — the sample should be a double set, because it exercises the follower/flush-bolt plan too.

Field note: "Ask for the installation guidance before you order" is a procurement move, not a courtesy. A glass-lock product line without written tightening sequence and pad specifications is a product line where the contractor's insurance funds the learning. The annotation: the sample stage converts panel-crack risk from a nine-figure-tenant complaint into a one-panel replacement.

The Spec Sheet You Fill In Before the RFQ

CR: So when I finally write the order, what does the line-item spec contain?

SP: These eight lines, per opening group. Anything you leave blank is a risk you accepted unknowingly.

LineSource of valueStatus in this article
Supported glass thickness band (min–max, actual mm)SLK-G200 product pageto verify in writing — transcribe, never assume
Mount architecture (clamp-on / patch-adjacent / drilled)survey outcome, Scene 2chosen per opening
Credential set (fingerprint / passcode / RFID card / app-Bluetooth / key)product page per SKUto verify in writing — the catalog spans all of these; confirm per model
Handed orientation + follower/flush-bolt planpair layout, Scene 5—
Strike anchorage type and hardwarefixed-side conditionper drawing
Power configuration (battery type, count, access)product page—
Network expectation (app/Bluetooth vs any Wi-Fi offering)product pagecheck the model’s published specification whether Wi-Fi is offered; the catalog's glass line is not documented here as a Wi-Fi product
Emergency access path (mechanical override or equivalent)product page—

Cells marked — have no documented value in this article’s sources; obtain the figure from the supplier’s written specification.

CR: Quick sanity check on credentials — storefront in a public arcade; staff carry no cards.

SP: Then a passcode or fingerprint-first configuration is the human answer, with a key or override path the tenant trusts. The catalog's unlocking-method vocabulary — fingerprint, passcode, RFID/IC card, mechanical key, app/Bluetooth — is broad; which subset a given glass SKU carries is a per-model fact. Don't let a reseller guess for you.

Field note: This table doubles as the article's core artifact: a frameless-door RFQ skeleton where every contested value has a named source. The manufacturer-side honesty built into it: we keep three glass models in a 79-model catalog and none of their numeric fit values get quoted secondhand. Where other door families appear in this article, the same rule applies — SLK-9936G, SLK-9905A, SLK-8831 and SLK-1104 specifications are product-page transcriptions, not conversation.

Reading the Job Back: Eight Openings, Three Orders

Consider the illustrative job one more time, this time from the order side. Six single-leaf frameless storefront doors: undrilled tempered panels, patch-hung, clamp-on no-drill architecture, same measured thickness band if the glazier used one batch — verify per panel anyway, because mixed batches are common. Two double-leaf lobby doors: clamp-on active bodies, follower-or-flush-bolt inactive plan per pair, strike anchorage on the outer fixed panels, ordered as two sets rather than two loose locks.

That is three purchase conversations, not one: singles bulk line, doubles set line, and a sample stage that precedes both. Quantity language stays quote-side — this factory publishes no minimums or prices — but the structure is yours regardless of supplier: group by mounting architecture and set composition, and one RFQ covers eight openings without a single guessed specification.

A closing annotation from the specialist chair: contractors routinely ask which lock is "best" for frameless glass, and the factory's real answer is that frameless glass is the least forgiving door family in commercial work. It offers no frame to borrow, no wood to rout, no metal to tap, and no post-tempering correction. The door tells you what you can mount — your job is to record what the door said, accurately, before the money moves.

Where This Goes Next

When the worksheet and the opening-group structure are filled, the next step is documentation, not negotiation: the category of purpose-built glass-door locks shows what this line covers, and samples for bench-fit verification exist precisely for the Scene 6 risk profile. To put the measured worksheet, photos and opening-group list in front of engineers who read fit envelopes for a living, use the quote request page — that is where to verify in writing stops being a blank and becomes a transcription.

Il tuo carrello
La tua esperienza su questo sito sarà migliorata consentendo i cookie Informativa sui cookie
Chat on WhatsApp