Slk 239 door fit notes: A procurement field guide to SLK-239 door fit questions, covering measurements, specification gaps, supplier evidence, and fit approval.

Pubblicato il: ott 31, 2023

SLK-239 Door Fit Questions, Answered for Procurement Teams

SLK-239 Door Fit Questions, Answered for Procurement Teams

These slk 239 door fit notes turn the published SLK-239 record into a procurement worksheet for evaluating real doors rather than assuming compatibility. The distinction matters because the supplied catalogue identifies the panel, mortise, access methods, finishes, power arrangement, and management platform, but its Door fit field is blank. A buyer can therefore prepare the right measurements and supplier questions without treating incomplete information as a fit approval. Before using any recorded specification in a purchase decision, confirm on the dated product page for the specific SKU.

Direct answer. In short, slk 239 door fit notes is the subject of this piece. slk 239 door fit notes is where the work on slk 239 door fit notes sits. slk-239 is what has to be evidenced before anyone signs. A slk 239 door fit notes is a component behaviour guide. It covers limits. It covers failure modes. slk 239 door fit notes decides whether slk 239 door fit notes is acceptable for this build.

slk 239 door fit notes is used here in the narrow sense set out in slk 239 door fit notes. It is a working definition built for slk 239 door fit notes. It is not a statutory one, and it has to be read against the market and product concerned.

  • Test what it does — confirm on the dated product page for the specific SKU behind slk 239 door fit notes
  • Test where it stops — record where the technology in slk-239 stops working
  • Plan the manual path — name the mechanical path that remains if slk 239 door fit notes fails
  • In slk 239 door fit notes, this sequence is what slk 239 is checked against.

Annotated source reading: what SLK-239 records

And what it.

Published fieldAnnotated SLK-239 recordProcurement interpretation
AccessRFID/IC card: Standard; mechanical override: StandardCredentials and emergency access are identified, but their physical fit is not established.
Platform and networkHotel lock management software; standalone lock; PC-linked card encoder; no in-room network requiredThis defines the management arrangement, not the lock’s mechanical envelope.
MortiseNo. 2 hotel mortiseUseful as a lock-family reference, but not a substitute for dimensioned drawings.
Panel330 × 75 × 25 mm; aluminum alloyRecorded panel dimensions must not be reinterpreted as complete door-fit limits.
FinishBlack, silver, and red antique bronzeFinish selection does not change the required fit evidence.
PowerFour AA alkaline batteries; low-battery alert: StandardPower is documented; access to the battery compartment still needs a site check.
Door fit— in the supplied catalogue rowApplicable thickness, backset, faceplate, mortise, and door-type limits remain open.
Environment— in the supplied catalogue rowDo not infer suitability for exposed, high-humidity, or other special locations.
DocumentationDimension drawings, installation guide, and full datasheet available on requestThese are the appropriate evidence to request before release.

The important finding is not that SLK-239 fails to fit a particular door. The finding is that the current record cannot answer that question by itself. Panel dimensions describe one published object; they do not state how the complete lock interacts with the door leaf, frame, latch, strike, spindle, or cylinder.

From door sample to fit evidence

An Office Smart Lock Site Survey can capture the measurement pattern needed for this review. For retrofit work, the Smart Lock Retrofit Site Survey is the better starting point because existing mortise cases, frame rebates, and previous hardware may constrain the installation.

The SLK-239 door fit checklist should connect each physical measurement to a supplier response:

flowchart TD
  A[Assign door reference] --> B[Record door leaf]
  B --> C[Record opening and frame]
  C --> D[Request dimensioned drawing]
  D --> E[Compare critical dimensions]
  E --> F[Check hardware clearances]
  F --> G[Record approval or hold]

The flow is deliberately evidence-led. A door photograph may help the supplier understand the installation, but it cannot substitute for dimensions. A product photograph may explain the visible panel, but it cannot establish the concealed mortise geometry. Every critical comparison must use a drawing, measurement sheet, or documented site condition tied to the selected SKU.

Door leaf thickness, construction, and handling

A repeatable door thickness measurement is the first field request. The buyer should record the door identifier, construction material, leaf thickness at the lock line, thickness at the hinge side, and whether the door is new or already prepared. The two thickness readings help expose tapered or irregular leaves; they do not establish a tolerance that the supplier has not documented.

Required fieldSurvey instructionQuestion for the supplier
Leaf constructionRecord timber, metal, composite, glass, or another stated construction.Which construction types are covered by the submitted drawing?
Door thicknessRecord actual measurements and their locations.What applicable range and measurement method apply to this SKU?
Door conditionIdentify new fabrication or retrofit status.Does the proposed preparation method apply to both conditions?
Swing and handingRecord opening direction and handing.Is the mortise and spindle arrangement reversible or handing-specific?
Existing preparationMark the position of any current lock, bore, or cutout.Can existing preparation be reused, and what evidence demonstrates compatibility?

For a repeatable survey, assign one measurement point at lock height and use the same tool, unit, and method for every leaf in the same door class. Record two or three readings rather than selecting the most convenient value, and mark the position of each reading. If a bevel, raised profile, tapered core, or uneven surface makes a reading uncertain, preserve that observation instead of averaging it away. Separate finished leaf thickness from frame-stop clearance, rebate depth, and cutout depth. The supplier must state which physical feature its applicable range describes. Until that definition is supplied, repeated measurements improve the site record but do not create a manufacturer tolerance.

Do not convert one convenient measurement into a claimed operating range. Ask the supplier to define the range, reference points, accepted construction, and any permitted site tolerance.

Backset, spindle position, and stile space

The backset measurement must use a stated datum. In some lock drawings, the dimension is measured from the door edge to the spindle or cylinder centerline; other architectural references use a different point. The RFQ should therefore request the measurement definition as well as the number.

Record the distance from the door edge to the relevant centerline, the stile width at the lock position, the centerline’s vertical location, and the handing. Ask whether the dimension is fixed or adjustable and whether there is an approved adjustment range. The reference “No. 2 hotel mortise” identifies the recorded mortise family, but it does not safely replace the backset and centerline information a buyer needs.

For repeat or multi-door orders, use two independent surveyors for a sample of each proposed door class. Compare their readings, resolve differences against the written datum, and preserve both values until the cause is understood. A sample also needs a selection rule: choosing the easiest door can hide a boundary condition. Select the sample to include expected minimum and maximum thickness, narrowest usable stile, closest case position to the edge, and the most complex frame condition. These are sampling rules, not claims about SLK-239 limits. Any door outside the reviewed sample remains conditional until a matching comparison is recorded. One successful installation is not evidence for an entire project.

The fitting should not be approved when the supplier drawing and site measurement use different reference points.

Mortise case, faceplate, latch, and strike geometry

Request mortise case dimensions and faceplate dimensions as separate fields. A buyer also needs the relationship between the case, spindle, door edge, latch, and strike rather than a list of unconnected dimensions.

Fit elementEvidence to requestWhy it affects approval
Lock body or mortise caseCase width, height, depth, fixing centers, and spindle referenceEstablishes whether the case enters the prepared door.
FaceplateWidth, height, fixing centers, and edge offsetsDetermines whether the faceplate fits the routed or drilled opening.
Latch or deadboltProjecting dimensions and operating configurationChecks operation and clearance; a deadbolt must not be assumed where the record is silent.
Strike platePlate dimensions and fixing-center positionsEstablishes alignment with the lock faceplate.
Strike keeperKeeper dimensions, depth, and fixing methodDetermines whether the frame can receive the supplied or approved keeper.

Transcribe the returned drawing into a comparison worksheet rather than comparing marks on a printout. Use one row per interface, retain the drawing revision beside every value, and state whether the comparison is matched, open, or rejected. A difference can be marked as passed only when the supplier supplies a tolerance or the approver records an agreed deviation.

InterfaceSite recordSupplier drawing recordStatus
Leaf thicknessReading point, range, and constructionApplicable range and reference featureMatch, open, or reject
Backset and spindleDatum, centerline, and handingDimension, adjustment range, and referenceMatch, open, or reject
Mortise and faceplateExisting or planned preparationCase, faceplate, fixing, and edge referencesMatch, open, or reject
Frame and strikeRebate, reveal, stop, and keeperInterface dimensions and approved accessoriesMatch, open, or reject
Hardware clearanceHandle, cylinder, closer, and wall conditionsProjection and required operating clearanceMatch, open, or reject

If the proposed configuration includes a deadbolt, label it explicitly on the RFQ and drawing request. If it does not, record that absence.

Panel, spindle, handle, cylinder, and emergency access

The recorded panel dimensions are 330 × 75 × 25 mm. These dimensions do not answer how far the panel projects from the door, how the spindle reaches the mortise, or where the cylinder and override key can be installed. Those are separate fit questions.

The supplier response should cover:

  • Handle or lever projection on the room and corridor sides.
  • Spindle length, section, engagement, and permitted projection.
  • Cylinder collar or rose dimensions.
  • Mechanical override key orientation and required clearance.
  • Fixing positions for the escutcheon or panel.
  • Any restriction imposed by door thickness or stile width.
  • Whether the emergency access arrangement changes for a retrofit door.

Before irreversible site preparation, make the approval package reconstructable: attach the final measurement sheet, marked drawing, comparison worksheet, exception log, and door reference. For a first or atypical installation, ask the supplier whether a full-size paper or non-marking template is available for checking panel and handle projection without drilling. Check the closed and open positions, the approach to the lever or key, nearby wall or frame clearance, and any closer or hold-open hardware already present. If a temporary mock-up is proposed, agree in advance what may be marked, what must remain reversible, and who accepts the result. A mock-up can support a decision but cannot silently replace missing technical limits.

The catalogue records mechanical override as standard. That confirms the access feature category; it does not provide the cutout, key orientation, or installation clearance. Treat those items as open until a dimensioned document or approved fit instruction covers them.

Door type, frame, rebate, and special conditions

The SLK-239 Door fit field does not state suitable door types. Procurement should describe the actual opening instead of relying on a general category label. The survey package should identify the frame type, door swing, rebate depth, reveal, existing mortise, strike arrangement, and any unusual edge condition.

For a glass, narrow, or specially profiled leaf, ask whether a patch fitting, alternative escutcheon, or other adapter is proposed. Record the accessory as part of the ordered configuration rather than treating it as an assumed inclusion. For retrofit doors, photograph the existing preparation and include those images with the measurements; they help the supplier assess reuse without replacing dimensional evidence.

The catalogue’s Environment field is also blank. If a door is exposed to weather, unusual humidity, or another special condition, request the relevant operating evidence for that location and configuration. Do not transfer suitability from a different SKU, finish, or installation.

Treat the blank Door fit field as a controlled information gap

A missing field can be managed; an undocumented assumption cannot. These slk 239 door fit notes should travel with the quotation so that the buyer, supplier, installer, and approver see the same open items.

Recorded itemDecision valueWhat it cannot replace
Panel dimensionsIdentifies the published panel sizeDoor thickness, backset, mortise depth, or stile limits
No. 2 hotel mortiseIdentifies the recorded lock familyCase dimensions, faceplate geometry, or latch position
RFID/IC card and mechanical overrideIdentifies recorded access methodsPhysical credential-reader or cylinder clearance
Finish optionsSupports finish selectionMechanical fit or handling clearances
Available documentationCreates a route to evidenceApproval before the evidence is reviewed

Mark each missing item as supplier action, site action, or accepted exception. A controlled gap has an owner and a documented closure condition. An informal assumption does not.

Fit decision table for procurement release

Use the following decision table at the end of the evaluation rather than treating the SLK-239 model name as an automatic approval.

DecisionEvidence conditionProcurement action
Approve for the represented doorThe dated drawing covers the SKU, critical dimensions match, and unresolved items are closedRecord approval against the specific door reference and drawing revision.
Conditional approvalA defined noncritical item remains open, with an acceptable written assumption and supplier evidenceLimit approval to the stated condition; do not extend it to another door class.
HoldThe Door fit field remains the only evidence, the drawing is missing, or a critical dimension cannot be matchedKeep the configuration unapproved and issue a precise fit-data request.
Reject the proposed fitThe dimensioned evidence conflicts with the door, or the required preparation is excluded from the offerSelect another configuration or door treatment and document the reason.

An approval for one representative door does not approve every door in a project. Doors can differ by construction, thickness, handing, frame, existing preparation, and hardware position. Map each approval to the evidence and door reference that support it.

RFQ fit data package and supplier response template

RFQ fit data should arrive as one controlled package, not as fragments copied into a chat message. Request the door schedule, completed measurement sheet, dimensioned installation drawing, installation guide, full SKU datasheet, and revision record.

RFQ fieldRequired supplier responseEvidence to attach
Applicable door thicknessRange, measurement points, and construction conditionsDrawing or technical note
Backset and spindle positionDimensions with clearly identified datumsMarked drawing
Mortise and faceplateCase and faceplate dimensions with fixing centersDimension drawing
Door and frame typesIncluded and excluded door conditionsWritten scope
Hardware clearancesHandle, spindle, cylinder, and key-access requirementsInstallation guide
Document controlSKU, finish, configuration, drawing number, and revisionCover sheet or dated PDF

The SLK-239: Reading the Published Specification Without Guesswork guide can be used to distinguish published fields from later evidence. The Configuring SLK-239: Credential Choices and Management Tools memo settles credential and management choices, but those choices do not replace mechanical fit data. The SLK-239 Order Checklist for Project and Repeat Purchases becomes the handoff control once the fit package is approved.

Door fit verification sequence for evaluation

Door fit verification should run in a fixed sequence so that measurements, documents, and decisions remain aligned:

  1. Assign a stable reference to each door or repeated door type.
  2. Complete the measurement sheet without leaving measurement points undefined.
  3. Send the RFQ fit data package to the supplier.
  4. Compare the returned drawing against every critical site dimension.
  5. Check hardware, frame, and access conditions that a dimension-only comparison may miss.
  6. Record the approval, conditions, rejected configuration, or hold against the correct drawing revision.

Consider an illustrative refurbishment with new timber leaves, retrofit metal leaves, and one glazed entrance. The project may repeat similar finishes and hardware, but that repetition does not establish identical preparation. Door fit verification should classify the three constructions separately until evidence links them to an approved range.

The same question is worked through in more detail in standalone vs connected smart locks. That is the same question slk 239 door fit notes has to answer here.

Direct answers to the recurring fit questions

The table below gives procurement a short answer first. Any value that affects a purchase decision still needs to be confirmed on the dated product page for the specific SKU and supported by the applicable project document.

Buyer questionDirect answer from the supplied recordEvidence still required
What door thickness is supported?No applicable range is published in the Door fit field.Supplier-stated range, measurement method, and construction conditions.
Which door types are suitable?No suitable door types are stated in the supplied record.A list of included and excluded door conditions.
What is the backset?No numerical backset is published.A drawing that defines the datum, centerline, and tolerance.
What are the mortise case dimensions?The record names a No. 2 hotel mortise but gives no case dimensions.Case width, height, depth, fixing centers, and spindle reference.
What are the faceplate dimensions?No faceplate dimensions are published.Width, height, fixing centers, and door-edge offsets.
Does 330 × 75 × 25 mm describe the complete installed lock?No. It is the published panel dimension.Drawings covering the panel, mortise, faceplate, and installed projection.
What spindle and handle are required?Neither is dimensioned in the supplied row.Spindle specification, handle projection, and handing details.
Is there mechanical emergency access?Mechanical override is recorded as standard.Key orientation, cutout requirements, and operating clearance.
What latch, deadbolt, and strike dimensions apply?No such dimensions are stated.Configuration-specific latch or bolt data, faceplate, strike plate, and keeper drawings.
Does the RFID or PC software affect the door fit?The access and platform methods are recorded, but they do not answer mechanical fit.Physical reader, cylinder, spindle, and installation-clearance details.
What should the supplier send?Dimension drawings, an installation guide, and a full datasheet are available on request.A dated, revision-controlled package tied to the selected SKU.

Procurement sign-off and commercial handoff

The final fit record should be concise enough to travel with the commercial request without losing its evidence trail.

Sign-off itemCompletion condition
Door referenceMeasurement sheet identifies the physical door or approved door type.
Supplier documentDrawing and guide identify the selected SKU and revision.
Critical comparisonThickness, backset, mortise, faceplate, strike, and hardware items are marked matched, open, or rejected.
Exception recordEvery condition states its owner, scope, and closure evidence.
Procurement decisionApproval is limited to the doors and configuration represented by the reviewed evidence.
Order packageThe approved fit record accompanies the catalog, configuration, and quote request.

When those fields are complete, the buyer can request a catalog for the controlled documents and request a quote with the fit package already attached. The commercial message should identify the SLK-239 configuration, approved door references, drawing revision, and any explicitly excluded conditions. That sequence keeps mechanical fit separate from credential design, software selection, and repeat-order administration, while giving each decision a traceable basis.

Il tuo carrello
La tua esperienza su questo sito sarà migliorata consentendo i cookie Informativa sui cookie
Chat on WhatsApp