UAE door thickness survey worksheet: survey UAE hospitality doors for thickness, backset and lock fit, then issue a clear hardware schedule for integrator.

Publicerad den: aug 23, 2023

Door Thickness and Backset Variance in the United Arab Emirates: A Survey Worksheet

Door Thickness and Backset Variance in the United Arab Emirates: A Survey Worksheet

This piece treats uae door thickness survey worksheet as a decision document rather than a summary, and each section below carries one piece of the evidence. Commercial access packages for serviced residences combine unit doors, shared entrances, amenity doors and service areas with different materials, frames and hardware arrangements. Field measurements must therefore identify the actual opening rather than assume that every unit door shares one construction.

Direct answer. In brief, this article covers uae door thickness survey worksheet from uae door thickness survey worksheet to moiat-ecas. It states what to confirm about uae door thickness survey worksheet on the dated product page where a figure is involved. a uae door thickness survey worksheet defines entry conditions for one market. uae door thickness survey worksheet starts the approval conversation. Every uae door thickness survey worksheet condition names its evidence.

On uae door thickness survey worksheet, this article uses uae door thickness survey worksheet as the definition. It treats uae door thickness survey worksheet as a working definition specific to this market and product, rather than a general one.

  • Bound the scope — write down what uae door thickness survey worksheet has to settle in the united arab emirates before any hardware is ordered
  • Assemble the file — attach the document behind each claim in moiat-ecas, not a summary of it
  • Place the duty — record who signs uae door thickness survey worksheet and who keeps the record afterwards
  • Treat this as the uae door thickness survey worksheet sequence, with moiat ecas as the reference.

Use this uae door thickness survey worksheet to convert those observations into a bid-stage record. It separates measured evidence, unresolved exceptions, product-specific fit checks and approval actions so that a system integrator can issue a dependable hardware schedule without overstating what a site visit proved.

The Office Smart Lock Site Survey and Smart Lock Retrofit Site Survey offer adjacent methods for recording site conditions. The worksheet below focuses on the dimension and interface evidence needed when hospitality doors enter a tender package or consultant-approved procurement schedule.

Scope of the door measurement record

The survey records what was seen at each opening. It does not approve a lock by itself, declare an opening compatible, or replace a product-specific installation drawing. Each unique door assembly receives one completed record, while repeated doors may be grouped only when their construction, measurements, interfaces and photographs match.

The survey should be completed before a bidder fixes a hardware allocation. In a tender-packaged hospitality project, the contractor may receive door schedules and shop drawings at different stages, while the consultant may request a mock-up after the first physical review. A controlled survey gives each party the same basis for comparison.

For every proposed smart lock, the bidder must confirm on the dated product page for the specific SKU and the current fit or installation drawing. The survey answer should identify the document revision, not merely say “within range.” Where site evidence and the drawing differ, the item remains conditional until clarified or demonstrated through an approved mock-up. What can be supplied is listed in the smart door locks.

Establishing one traceable door register

Assign each surveyed opening a reference that can be carried through the survey, mock-up, submittal and purchase schedule. A practical reference combines the building, level, room or functional space, and the door mark shown in the project information. Keep the room number, architectural door mark and estimator’s item number as separate fields so a drawing revision does not break the trace.

The register must identify whether the opening is a serviced-residence unit door, apartment entrance, shared lobby, amenity entrance, staff area, cycle store or another access point. Record leaf construction, frame type, handing, swing direction, existing lock or hardware, and any door closer. These entries explain why two openings with similar leaf dimensions may still require different lock arrangements.

A smart lock site survey is strongest when each row has evidence attached. Include an unaltered overview photograph, a close photograph showing the measurement reference, and a photograph of any existing faceplate or mortise arrangement. Label photographs with the same opening reference and measurement date. Record who took them and whether the images were checked against the row before issue.

Do not silently replace missing measurements with nominal values from the door schedule. Enter “not measured,” “not accessible” or “pending removal of obstruction” in the status field and raise the corresponding exception. A visible gap in the evidence is safer than a precise-looking value that cannot be reproduced.

Defining thickness and backset for the survey team

The door thickness measurement records the physical leaf thickness at the agreed reference points rather than copying a nominal profile size. Where the leaf construction changes across its width, record the values at the lock stile and latch stile, or at the positions defined by the proposed lock drawing. Add the measurement locations to the record so another surveyor can repeat the check.

A composite leaf, folded profile, glazing bead or applied finish can make the edge, face and lock-stile thicknesses differ. Mark any seal, laminate, cladding or trim that affects the lock pocket. If a protective film or temporary site covering remains in place, photograph its condition rather than treating the covered dimension as final.

The backset measurement must follow the datum used by the current lock drawing. Identify whether the drawing measures from the door edge to the spindle, handle, cylinder or bolt centreline. If the reference is not stated, do not select the most convenient interpretation. Ask the manufacturer or door-hardware team to define the datum and attach that definition to the survey.

The door fit survey should also capture frame section, lock pocket, edge profile, handing and swing. A dimension match does not resolve a mortise-depth conflict, an unsuitable edge profile or a closer arm that cannot travel. The Glazed Partition and Swing Door Assemblies: What It Means for Smart Lock Selection in the United Arab Emirates article explains why the door assembly, rather than the lock alone, must be considered.

For glass and aluminium openings, record the actual door construction and hardware interfaces rather than adapting a timber-door form. The Glass and Aluminium Doors in the United Arab Emirates: Smart Lock Fit Constraints guidance is a useful companion because glazed doors may require a different pocket, rail, channel or fixing arrangement. Do not extrapolate a timber mock-up to a glass assembly.

These definitions make the uae door survey a repeatable record. They also let the reviewer distinguish a dimensional variance from an unresolved product, frame or hardware question.

Field capture for every door assembly

Table 2 — uae door thickness survey worksheet field capture.

Field groupRequired entryEvidence or bidder response
Project controlProject, building, level, opening reference, survey date and record revisionState the drawing and schedule revisions used during the visit
Opening useUnit, apartment entrance, lobby, amenity, staff area, cycle store or other stated functionIdentify the access pattern and operating owner
Door identityRoom number, architectural door mark, estimator item and unique survey referenceKeep each identifier visible in the photograph filename
Leaf constructionTimber, metal, glass, composite or mixed construction; finish and visible core or claddingPhotograph the edge, face and lock stile
Door thickness measurementMeasured value, unit and location on the leafRepeat at defined points where thickness varies; do not use nominal size alone
Backset measurementMeasured value, unit, edge reference and centreline definition usedAttach the dated fit drawing that defines the datum
FrameFrame type, section, profile, stop position and available lock pocketRecord the visible frame detail and any cover or trim
Handing and swingHand, opening direction, active or inactive leaf, handing convention usedAttach a plan-view sketch where handedness is disputed
Existing hardwareMortise or rim lock, cylinder, handle, escutcheon, bolt, closer, reader and strike arrangementPhotograph the installed arrangement and record visible damage
InterfacesFrame, adjacent wall, glazing, door stop, closer, fire hardware and access-control equipmentName the trade responsible for each interface
Site conditionsDust, heat exposure, direct weather exposure and construction obstructionLink condition to a proposed test or mitigation rather than a generic note
EvidenceOverview, measurement, interface and exception photographsNumber images against the opening reference
VarianceVariance code, reason, effect on fit and proposed dispositionState who will resolve it and the required evidence
Commercial dependencyMock-up, consultant approval, supplier clarification or tender clarificationIdentify the item that cannot be released until closed

A completed field is not necessarily a completed record. The field must carry a value or status, an evidence reference and an owner for any follow-up. For example, “43 mm” is incomplete without the unit, measurement location, photograph and drawing revision used to compare it.

Comparing fit evidence before releasing a hardware line

Do not convert survey measurements into a binary fit decision until the comparison basis is present. The table below gives the integrator a practical decision rule without assigning a universal acceptable range.

Fit evidence stateSurvey decisionBid responseRelease condition
Dimensions and interfaces match the dated drawingConfirmed by surveyState the proposed SKU and identify the applicable fit drawingProcurement may schedule the item subject to the normal project approvals
Most evidence matches, but one interface remains unresolvedConditionalList the missing measurement, document or mock-up actionRelease only after the named party closes the condition
A recorded dimension conflicts with the proposed configurationConflicting evidenceExplain the conflict without changing the field measurementResolve by clarification, revised selection or approved mock-up
No product-specific drawing is available for comparisonNot assessedRequest the dated product page and installation informationNo compatibility statement may be issued from the survey alone
The opening belongs to a different hardware or construction packageOutside this lock lineRecord the applicable door or hardware scheduleTransfer the action to the responsible package

This comparison table should travel with the door schedule. It allows the consultant to see why one line can be released, why another needs a mock-up and why a third remains outside the current hardware scope. It also reduces the chance that a visually similar door will be treated as an exact equivalent.

A real decision-comparison table is more useful than a final column marked only “pass” or “fail.” The commercial consequence belongs beside the evidence because a conditional line may require a revised tender quantity, an alternative product request, a site visit or a separate installation work package.

Applying the worksheet to serviced-residence door types

A serviced residence may contain several door populations that should never be collapsed into one nominal door type. Unit entrances may use timber, metal or composite leaves. Shared lobbies can include glazed or aluminium elements, while amenity doors may have different frame and hardware arrangements. Cycle stores and service rooms add their own access requirements but may sit outside the electronic-lock package.

The serviced residence door schedule should therefore preserve the functional use of each opening. Mark whether an access credential is expected at the unit, lobby or amenity door, and identify whether a staff master is required. This is a physical survey worksheet rather than a credential-design document, but the intended access pattern helps the reviewer notice when a proposed handle, reader position or door schedule conflicts with the operating plan.

Treat hospitality access hardware as part of the door assembly. A faceplate may interact with a mortise lock, a rim lock, a closer, a bolt, a latch, a hold-open arrangement or coordinated access equipment. The survey should show those items rather than asking the lock supplier to resolve unknown interfaces.

Common-area layouts and staff accommodation can introduce different operating expectations, but the record should remain operational. Note shared circulation, privacy-sensitive residential areas, Arabic and English documentation requirements, housekeeping access and any planned maintenance window. Record the operator’s instruction instead of making an assumption about user behaviour.

The Specifying Smart Locks for Hospitality and Serviced Residence Projects in the United Arab Emirates article broadens the specification beyond the lock body. Use both documents together: one records the opening, while the other checks that the proposed hardware, handover and operating assumptions form a coherent package.

Coding variance without averaging it away

A repeated nominal door may still conceal a physical variant. Doors from different production batches, replacements or floor levels can have different finishes, frames or hardware arrangements. Survey representative openings, but record the evidence that justifies grouping. If no comparison is possible, survey the additional opening.

Table 3 — Variance codes for the door schedule.

CodeTriggerRequired response
V-TLeaf thickness differs across measurement points or from the referenced drawingRecord every measured location and request the applicable fit basis
V-BBackset or its stated datum differs from the proposed configurationConfirm the drawing definition and physical edge reference
V-FFrame section, pocket, stop or rebate does not match the assumptionAttach frame photographs and assign a frame or carpentry action
V-SHanding, swing or active-leaf arrangement is uncertainAdd a plan sketch and obtain consultant or installer confirmation
V-HExisting or coordinated hardware conflicts with the proposed lockIdentify the hardware owner and required coordination drawing
V-GGlass, rail, channel or fixing details are incompleteObtain the assembly drawing and complete a representative mock-up
V-ISurvey access or concealed construction prevents measurementRecord the obstruction, access condition and revisit requirement
V-AApproval or documentary evidence remains outstandingState the evidence required and the party who will provide it

Never average measurements across incompatible doors to make a schedule tidier. An average can conceal the thickest and narrowest conditions that the installer will encounter. It can also remove the evidence needed to select a lock or approve a site modification.

For every coded variance, add four items: the observed evidence, the procurement effect, the proposed resolution and the accountable party. “Contractor to resolve” is too broad unless it identifies whether the contractor must adjust the frame, remove an obstruction, provide a revised drawing or demonstrate the proposed configuration.

A closed variance should include its closing evidence and the record revision in which it was closed. This protects the final purchase schedule from silently carrying forward a stale survey result.

Bid clauses that make the worksheet enforceable

The tender or quotation should state which party collects the measurements, which party checks the product-specific fit evidence and what happens when the survey and drawings disagree. The survey must return with the technical response, not arrive later as an uncontrolled site document.

Table 4 — uae door thickness survey worksheet response schedule.

Bid clauseBidder responseSupporting evidence
One record per unique door assemblyComplete every applicable field and identify each unresolved itemSigned worksheet, photographs and issue register
Dimensions must be measuredProvide values, units, reference locations and the drawing revision usedClose photographs and a repeatable measurement method
Nominal schedule sizes do not replace a site checkIdentify any opening inspected from drawings onlyMark it as unsurveyed and state the consequence
Product-specific comparison is requiredIdentify the dated product page and fit drawing for each proposed SKUCurrent documents and a line-by-line comparison
Variances may not be averagedList each physical variant and the associated schedule impactDoor-by-door variance register
Mock-ups require a written dispositionState who will build, witness, test and approve the representative sampleMock-up record and signed approval
Drawing changes trigger reviewIdentify the affected survey records and proposed actionsRevised schedule and comparison note

Use clauses such as “the bidder shall confirm” rather than an unsupported statement that a lock “fits.” The bidder remains responsible for demonstrating the configuration it proposes, while the integrator remains responsible for making the survey records available and controlling revisions.

Where the project combines new installation with retrofit work, state which survey template applies to each workstream. The Smart Lock Retrofit Site Survey reference can support the condition assessment for retained doors, but it does not remove the need for a product-specific fit comparison on this worksheet.

Require the response to identify substitutions explicitly. A later catalogue change must not be treated as equivalent to the surveyed and bid configuration. Any substitution should return through the same drawing, interface and approval checks.

Keeping MOIAT and ECAS evidence outside the dimension decision

Door-fit evidence and product-conformity evidence answer different questions. The survey records whether the physical opening matches a proposed installation configuration. It does not determine whether a particular lock falls within UAE MOIAT/ECAS-style registration, any GCC G-Mark scope, or another documentary route.

Ask each bidder to identify the applicable route for the specific SKU and project scope, then attach the dated evidence it relies upon. The answer should be checked against the current requirements rather than copied from an earlier tender. The Reading MOIAT and ECAS Documents for Smart Locks: A Buyer Guide for the United Arab Emirates guide provides a structured way to read the documents after the technical team has identified what to request.

CONFIRM-WITH-LOCAL-MOIAT-ECAS: Confirm with the relevant authority and each bidder which registration or certificate route, if any, applies to the specific lock and project scope; retain the dated document and verify its scope.

A door survey can still reveal when a proposed lock needs separate façade, interior or life-safety review. The relevant hardware package and door assembly should be identified, but the survey team should not issue the approval itself.

CONFIRM-WITH-LOCAL-FIRE-SAFETY: Confirm which authority signs off on each door assembly and whether changes to the lock, faceplate, frame, closer or other life-safety hardware require separate approval.

Keep these confirmations visible in the tender checklist. Removing them because a dimension matches leaves a separate approval trail incomplete.

Moving from survey to mock-up and approval

The survey closes measurement gaps; the mock-up closes construction questions that photographs cannot resolve. Select representative openings for timber, metal, glass or any distinct frame arrangement affected by the proposed lock. Do not use a conveniently accessible unit door to represent a materially different construction elsewhere in the building.

flowchart TD
    A["Create the door register"] --> B["Measure thickness and backset"]
    B --> C["Compare with dated fit drawings"]
    C --> D{"Evidence complete"}
    D -->|"No"| E["Hold the hardware assignment"]
    D -->|"Yes"| F["Submit the mock-up record"]
    E --> B
    F --> G["Release the approved schedule"]

Route the mock-up through the project’s named approval path. In a consultant-approved and contractor-led package, this may include the consultant, main contractor, door supplier, lock supplier and integrator. Record each role and signature in the mock-up document instead of relying on an informal message.

The mock-up record should show the selected opening, installed configuration, measured clearances, operating actions, hardware interfaces, photographs and unresolved observations. It should also identify the drawing and product-page revisions used during the review. A successful demonstration supports the tested configuration only; it does not automatically approve an untested door type.

After approval, issue a schedule with clear statuses: released, conditional, excluded or pending clarification. Preserve the survey and mock-up references in each line. This gives procurement a usable schedule while allowing technical teams to reopen a specific condition without restarting the whole survey.

Assigning credential and move-out responsibilities

A dimensionally correct lock still needs an operating owner. The first operational question is: who issues the resident’s first credential, and who removes it at move-out? Assign both actions before the hardware schedule is approved so that the access system has a named process owner.

Table 5 — Responsibility fields linked to the serviced-residence handover.

Operating actionOwner to be namedEvidence to retainService-window field
Issue the first resident credentialProperty or access-control operatorIssue record and referenceStart date and notice period
Remove access on move-outProperty or access-control operatorRemoval confirmationMove-out inspection and closure record
Manage the staff masterSecurity or operations teamControlled issue and audit trailShift and handover procedure
Recover a lost credentialNamed operatorIncident and revocation recordResponse route and access impact
Replace or service a unit lockMaintenance teamJob record and returned configurationResident notice and access plan

The operator’s service constraint is important. A small team may need notice before it can service a resident’s lock. Record that requirement without implying that every property uses the same schedule. Ask the operator for the actual notice period and the procedure for maintaining guest or resident access during a lock exchange.

Credential ownership should not be buried in a general handover list. Link it to the door schedule, the operator’s responsibility matrix and the service record. This prevents credentials from outliving a tenancy because the removal step was never assigned.

Why technical responses are returned for clarification

The most common reason for returning a smart-lock survey is not a dramatic dimensional conflict. It is incomplete evidence that cannot be checked against a product-specific drawing. Typical return causes include one unlabelled measurement, a copied nominal size, an outdated drawing revision, a missing handedness record and an image that does not show the measurement reference.

Another common issue is substitution by assumption. The respondent sees a timber unit door, selects a visually similar configuration and treats it as representative of a metal or glazed opening. The record must distinguish shared construction from actual construction. Repeated doors may be grouped only after the relevant dimensions and interfaces have been compared.

Survey forms also fail when exceptions have no commercial consequence. “Check on site” does not say which item is on hold or who can close it. Each exception must state the affected schedule line, the proposed action and the evidence needed for release.

A final response may be returned when photographs have been separated from their references, when the survey revision is absent, or when a mock-up approval is claimed without a record. These gaps are inexpensive to close during the bid stage and expensive to discover after an order is placed.

Review should be exacting without becoming obstructive. Ask for the missing evidence once, identify the rule it satisfies and preserve answered fields. The goal is a reproducible survey that installers, suppliers and reviewers can use without reconstructing the original site visit.

Pre-issue acceptance checklist

The person issuing the survey should complete a short quality review before sending it into the tender or approval workflow.

CheckPass condition
Opening traceabilityEvery row matches a room or functional space, architectural mark and photograph set
Measurement methodUnits, points, backset datum and drawing revision are stated
Material variationTimber, metal, glass and composite conditions are not silently combined
Interface completenessFrame, handing, swing, closer and existing hardware are recorded or marked unavailable
Product comparisonThe dated product page and fit drawing are named for each proposed SKU
Variance ownershipEvery exception has a disposition, evidence request and accountable party
Approval statusReleased, conditional, excluded and pending items are visibly separated
Revision controlThe issue register identifies survey revision, date, owner and next review point
Local confirmationsRequired MOIAT/ECAS and door-assembly confirmation lines remain in the tender record
Handover linkCredential issue, move-out removal and lock-service responsibility are assigned

A pass does not mean that every door has received the same product. It means the record contains enough evidence for the buyer to make a controlled procurement decision. Conditional doors remain visible until their conditions close, and excluded openings remain in the schedule so that another trade or package can own them.

Returning a usable door schedule

The completed package should contain the survey register, photographs, comparison sheet, variance log, product-specific fit references, mock-up record where used, and the approval trail. Include a short schedule that translates each opening into released, conditional, excluded or pending status. A bidder can then price or supply against a defined configuration, while the integrator can trace every decision to field evidence.

Keep the worksheet with the tender and shop-drawing records. When doors or hardware change, mark which rows require reinspection instead of issuing an undifferentiated revision. The commercial benefit is a smaller gap between what the surveyor observed, what the consultant approves, what the contractor can install and what the operator can support after handover.

When the file is ready, request a quote against the written requirement.

Din kundvagn
Din upplevelse på denna webbplats förbättras om du tillåter cookies. Cookiepolicy
Chat on WhatsApp