Door Thickness and Backset Variance in Australia and New Zealand: A Survey Worksheet
This piece treats australia door thickness survey worksheet as a decision document rather than a summary, and each section below carries one piece of the evidence. Regulatory brief · Distributor decision record · Australia and New Zealand
Direct answer. In brief, this article covers australia door thickness survey worksheet from australia door thickness survey worksheet to rcm-safety. It states what to confirm about australia door thickness survey worksheet on the dated product page where a figure is involved. An australia door thickness survey worksheet defines entry conditions for one market. australia door thickness survey worksheet starts the approval conversation. Every australia door thickness survey worksheet condition names its evidence.
This article defines australia door thickness survey worksheet through australia door thickness survey worksheet. The definition of australia door thickness survey worksheet is deliberately narrow. It is non-statutory, and it applies to the market and product being discussed.
- Define the scope — write down what australia door thickness survey worksheet has to settle in australia and new zealand before any hardware is ordered
- Produce the evidence — attach the document behind each claim in rcm-safety, not a summary of it
- Name the owner — record who signs australia door thickness survey worksheet and who keeps the record afterwards
- This is the sequence australia door thickness survey worksheet has to follow, anchored on rcm safety.
Issue. A remote worker accommodation portfolio can place timber, hollow-core, metal, glass and aluminium doors behind one access system. The australia door thickness survey worksheet gives distributors a traceable record of geometry while preventing a fit observation from being mistaken for product or project approval. It is intended for serviced apartments and similar managed rental portfolios in Australia and New Zealand.
Decision requested. Release a SKU to sample review only when the door ID, leaf thickness, backset datum and dated product drawing agree. Hold exceptions until a supplier, installer or local adviser supplies the evidence needed to resolve them. Do not merge physical compatibility, regulatory evidence and access turnover into one “fits the door” judgement.
Fit approval and regulatory approval need separate records
A door fit survey establishes whether the proposed lock can be considered against the measured leaf geometry without unapproved alteration. It does not establish which regulatory evidence applies to the SKU or project. Keep the measurement record, dated product drawing and project-specific evidence in the same quote file, but give each a separate approval status.
Use Hollow-core Internal and Aluminium Sliding Doors: What It Means for Smart Lock Selection in Australia and New Zealand as the selection companion. For distribution control, require each dimensional entry to identify its source, measuring party and date. Ask suppliers to distinguish a drawing dimension from a permitted adjustment range, and confirm on the dated product page for the specific SKU before approving a non-standard value. What the buyer's own file needs is in SLK-9905A Door Thickness and Compatibility Guide.
Measurement fields to capture on every leaf
The australia door thickness survey worksheet should create one row per physical leaf, not one row per property or lock model. For timber and hollow-core doors, record the construction and whether the measurement came from the actual leaf rather than a nominal schedule.
| Survey field | Required entry | Decision use |
|---|---|---|
| Door ID | Property, room and unique leaf reference | Prevents cross-assignment |
| Leaf construction | Material, core and panel description | Identifies fixing constraints |
| Leaf thickness | Measured value, units and measuring points | Compares with the SKU drawing |
| Backset datum | Edge reference and measurement convention | Prevents false comparisons |
| Bore geometry | Diameter, centre and relevant offsets | Checks the prepared opening |
| Edge and face clearances | Available space and obstructions | Identifies installation limits |
| Swing and handing | Direction, hinge side and opening position | Checks spindle and body clearance |
| Existing hardware | Locks, cylinders, keepers and strikes | Reveals preparation conflicts |
| Evidence | Scaled photographs and dimensioned sketch | Supports the supplier decision |
Measure smart lock door thickness at the latch stile and at additional points that expose unevenness; retain the readings rather than recording only an average. A smart lock backset measurement must state whether it runs from the door edge to the cylinder, spindle or another datum used on the drawing. Convert units once, identify the conversion, and preserve the original entry.
Resolve the backset datum before comparing numbers
A backset figure is not useful until its datum and direction are known. Record the edge from which the measurement was taken, the feature defining its endpoint, the handing direction and the measuring device. A reading taken from a decorative edge or the centre of a glass feature may not correspond to the lock body geometry in the product drawing.
Request a dimensioned drawing for the exact SKU and finish configuration. Where the supplier drawing and the field record use different definitions, obtain a written dimensional reconciliation. If that reconciliation cannot be obtained, hold physical fit approval even when the two numbers appear similar.
Build a regulatory evidence lane beside the geometry record
Treat rcm-safety as an internal evidence-lane label, not an approval outcome. Ask which EMC, radio or telecom evidence falls within the RCM scope for the exact SKU, who holds it and how it relates to the offered variant. Separately ask whether an adaptor-equipped or other powered configuration falls within an electrical-safety approval route.
CONFIRM-WITH-LOCAL-AUSTRALIAN-NEW-ZEALAND-COMPLIANCE-ADVISER: Confirm the RCM scope, electrical-safety route and responsible evidence holder for each specific SKU and power configuration.
Security grading requires another evidence request. Ask which AS/NZS 4145.2-style cylinder or lock security-grading evidence the project has requested and who may attest to it. The worksheet may record that request, but it should not assign a grade from appearance or from another product variant.
CONFIRM-WITH-LOCAL-ACCESS-CONTROL-SPECIALIST: Confirm which AS/NZS 4145.2-style security-grading evidence the project requires and which party may provide it.
Fire and egress suitability must also remain outside the geometry decision. Record door labels, project schedules and proposed alterations, then route them for local review. The sequence in Reading RCM Safety for Smart Locks: A Buyer Guide for Australia and New Zealand supports document review, while Building-code Egress Interpretation: The Australia and New Zealand-Specific Smart Lock Question Foreign Suppliers Miss addresses the project interpretation that must accompany it.
CONFIRM-WITH-LOCAL-BUILDING-CODE-ADVISER: Confirm the applicable fire and egress requirements, door-schedule status and approval route for each project before hardware alteration.
Decision table for releasing a distributor quote
Apply the decision to each door entry rather than to the whole order. A sample request may proceed while another leaf on the same property remains on hold.
| Decision | Trigger | Release condition |
|---|---|---|
| Proceed to sample | Measurements match the dated drawing | Evidence owner and project route are named |
| Engineering review | A value falls outside the stated geometry | Supplier supplies a written method |
| Local project review | Fire, egress or marked-door status is present | Local adviser confirms the route |
| Hold | Drawing, datum or measurement is missing | Missing evidence is supplied and logged |
| Split entry | Different doors need different treatment | Separate SKU and approval records are issued |
| Close exception | Revised method or door preparation is agreed | New measurements replace superseded values |
The mermaid workflow below makes the release status visible without converting a survey into an approval. Every “proceed” entry still depends on the evidence lane for the relevant project.
flowchart TD
A[Assign door ID] --> B[Measure leaf and frame]
B --> C[Record backset datum]
C --> D[Compare with dated SKU drawing]
D --> E{Fit confirmed?}
E -->|Yes| F[Complete evidence lane]
E -->|No| G[Open exception]
F --> H{All conditions closed?}
G --> I[Hold quote release]
H -->|Yes| J[Release sample request]
H -->|No| I
Exceptions for mixed door populations
The relevant door population includes timber and hollow-core internal doors, together with aluminium sliding and pivot doors and mixed timber, metal or glass construction in serviced properties. A leaf-thickness value alone does not establish the core, fixing method or available internal clearance. Record the actual construction and any existing preparation.
For aluminium sliding doors, identify the active leaf, panel construction, track position, stile width and available lock pocket. The fit constraints discussed in Glass and Aluminium Doors in Australia and New Zealand: Smart Lock Fit Constraints should be checked against the individual door rather than a building category. Flag proposed cutting, routing or retrofitting of a marked assembly for local review before work begins.
Readers comparing approaches usually start with the smart lock software trends. That is the same question australia door thickness survey worksheet has to answer here.
Access and turnover implications for serviced apartments
Serviced apartment access commonly combines app or code access at the unit, a fob at the lobby and a staff master credential for amenities. The operator may be unable to service a resident’s lock without notice, so a physical survey can require resident coordination even when the measurement task appears routine.
This overlaps with the earlier coverage in the smart lock hardware trends. That is the same question australia door thickness survey worksheet has to answer here.Record who grants access for measurement, installation and return visits. Also assign the issue of the resident’s first credential and its removal at move-out; otherwise a successful door-fit approval can still lead to credentials outliving the tenancy. Use the door ID to connect every physical exception to an installer, supplier or operations owner rather than leaving it in an unassigned spreadsheet.
Distributor approval packet and ownership
Attach the completed worksheet to every sample request and order revision. The distributor packet should contain:
- A unique door ID and dated measurement sheet.
- A scaled photograph with a visible reference object.
- The dimensioned drawing for the exact SKU.
- The backset definition and datum used.
- Any exception, proposed method and named owner.
- The applicable project evidence request.
- The local-confirmation route where relevant.
- A superseded-record marker after any correction.
Do not copy a generic declaration across variants, finishes or door types. Attach the completed record to the RFQ and sample request, request dated drawings with every revision, and keep the physical-fit decision separate from the regulatory evidence lane. The worksheet then gives Australia and New Zealand distributors a repeatable release mechanism without pretending that one nominal dimension represents the whole property.
Close the loop with requesting a quote.

