Slk 9l5 r door fit notes: use this SLK-9L5-R door fit runbook to measure clearance, qualify a retrofit and confirm installation evidence before procurement.

Publicat la: ian. 09, 2025

SLK-9L5-R and the Door It Has to Live In: Fit, Clearance and Retrofit

SLK-9L5-R and the Door It Has to Live In: Fit, Clearance and Retrofit

These slk 9l5 r door fit notes convert a site evaluation into a controlled sequence of evidence gates for procurement. Use them when the SLK-9L5-R is one candidate for a sliding door and the question is whether it can be installed without unplanned cutting, restricted movement or an unusable service path. The deliverable is a fit dossier, not a visual impression and not an installation instruction.

Direct answer. The one-line answer — slk 9l5 r door fit notes is the working record for slk 9l5 r door fit notes. slk 9l5 r door fit notes is worthless until slk-9l5-r is attached to it as evidence. A slk 9l5 r door fit notes is a component-level look at how the technology behaves. slk 9l5 r door fit notes is where the limits sit. slk 9l5 r door fit notes is verified on the dated product page.

The supplied catalogue record names the SLK-9L5-R as a “3D Face Recognition Smart Lock for Sliding Doors,” but its Door fit field is shown as “—.” It therefore supplies no verified panel dimensions, applicable door thickness, backset, template or clearance schedule. The model name identifies the intended door context; it does not establish which sliding-door construction can be fitted.

That evidence boundary determines the method below. Every gate ends in a documented status, every missing value becomes an assigned action, and no supplier or installer is expected to fill a dimensional gap from memory. The purpose is to create a record that procurement, site teams and suppliers can review against the same door.

Runbook at a glance

The workflow moves from document control to physical evidence. A failed gate returns the package to the affected measurement or interface check rather than allowing an unsupported assumption to travel downstream.

flowchart TD
A[Confirm SKU and evidence set] --> B[Classify door population]
B --> C[Measure leaf and frame]
C --> D[Map hardware interface]
D --> E[Check operating clearances]
E --> F[Run physical mock-up test]
F --> G{All approval gates passed}
G -->|Yes| H[Release fit approval]
G -->|No| I[Open an exception record]
I --> C

The runbook has four possible dispositions:

  • Approved: The applicable gates have objective evidence, and no unresolved item can change the mounting method or operating envelope.
  • Conditional: A named document or test remains outstanding, with an owner and release condition recorded.
  • Hold: The door population, SKU identity or dimensional basis is incomplete, so downstream review could be misleading.
  • Rejected: The available evidence shows that the proposed installation conflicts with the intended door or leaves an unacceptable service condition.

A rejected gate is a valid procurement result. It prevents an unsuitable configuration from entering a later order stage.

Evaluation boundary: what this review approves

This runbook answers one operational question: does the submitted evidence show that the SLK-9L5-R can be mounted on the representative door and operated without unresolved geometry? It covers the door leaf, frame or rail interface, hardware positions, user and service clearances, and the basic movements required after installation.

It does not establish suitability for every door in a portfolio. A sliding door may use different rail arrangements, stop positions, leaf thicknesses or face-edge constructions, even when the doors appear similar in a photograph. Doors must therefore be grouped only after their physical differences have been checked.

The catalogue record lists RFID/IC card, passcode, fingerprint, 3D face, mobile app and mechanical override as standard access methods. It records the style as “Fully Automatic Face Recognition Fingerprint Password Lock,” the finishes as “Red Bronze / Gunmetal,” and dimension drawings, an installation guide and a full datasheet as available on request. These are catalogue entries, not fit measurements; confirm on the dated product page for the specific SKU before any of them drives a procurement decision.

Use SLK-9L5-R Specifications, Field by Field to separate catalogue fields from the site evidence required here. Fit approval remains a physical-documentation decision even when the other fields are complete.

Required inputs and responsibility map

Before dispatching the survey, the requester should assemble a door schedule, available drawings, site photographs, a marked-up door schedule and any supplier dimension material for the exact SKU. The package should also identify the representative door, existing hardware to be removed, nearby wall or cabinet obstructions and the intended operating direction.

The dated product-page extract is a required input because catalogue data can change by revision. Record the source, access date, SKU description and drawing revision. If the product page and catalogue use different names, reconcile the identity before anyone measures or approves a mock-up.

RoleReceivesProducesAccountable decision
Requester or project leadDoor population and project intentSurvey scope and access planWhich doors represent the project
Site surveyorSurvey packet and measurement instructionDimensioned photos, measurements and obstruction notesCompleteness of site evidence
Supplier or product specialistSKU, measured door and interface questionsDated product evidence and drawing clarificationModel-specific fit information
Installer or hardware reviewerEvidence packet and sampleInterface assessment and test observationsWhether the physical installation method is workable
Procurement managerCompleted gates and exception registerFit disposition for the evaluation fileWhether fit evidence is sufficient to proceed

No role should close another role’s gate. In particular, a supplier drawing is an input to physical review, not a substitute for measuring the actual door.

Gate 0 — control the evidence baseline

Gate 0 prevents uncertainty about which product or drawing is being evaluated. The surveyor should not begin with an open-ended request for “lock dimensions.” The request must identify the SLK-9L5-R, state which catalogue fields remain blank and request only the information needed to compare the proposed interface with the door.

Evidence itemMinimum recordMissing-item action
Product identityModel name, dated product-page reference and evidence dateHold the survey until identity is reconciled
Drawing setDrawing title, revision, applicable SKU and unitsRequest the missing or superseded drawing
Door identificationDoor reference, location and photographAssign a traceable door mark
Population basisGrouping rule and representative unitKeep doors separate until differences are measured
Survey scopeMeasurements, interface checks and tests requiredIssue a corrected scope sheet

Keep every obsolete file in the exception log but mark it superseded. A mixed revision set creates a false appearance of precision, particularly when one sheet shows the panel while another shows the door interface.

If a drawing is marked “illustrative,” do not treat it as an installation template. If it lacks the SKU, revision or units, it can support discussion but cannot close a dimensional gate.

Gate 1 — establish the real door population

A door survey should start by classifying the doors that will actually receive the lock. The Smart Lock Retrofit Site Survey provides a useful retrofit-specific field structure, but the survey team must still confirm which observations apply to this project.

Group a door only when the following have been checked: leaf construction, thickness, face-edge arrangement, rail or frame arrangement, stop condition, existing lock position, surrounding wall build-up, opening direction and expected daily movement. Photograph the complete door in its installed context. A close-up of the face edge cannot show a wall return that will block the panel.

As an illustrative scenario, an office may contain several sliding leaves that appear identical from the corridor. One leaf may sit beside a plaster return, while another may have a different stile width or a closer mounted on the opposite face. The first group is not valid until the surveyor records and reconciles those differences. Such scenarios are planning examples, not claimed project outcomes.

Use this population record:

Population fieldRecordWhy it affects fit
Door referenceUnique mark tied to the project scheduleConnects measurements to the purchasing unit
ConstructionLeaf, rail, stile, glass or panel arrangementDetermines what can be drilled, bonded or adapted
Existing hardwareLock, pull, track, stop and closer positionsShows interference and removal scope
ContextWall return, cabinet, casing, threshold and traffic pathDefines the usable panel and service envelope
VariationRange or identified non-identical typePrevents an untested door from inheriting approval

The representative unit should be the least favourable defined condition, not merely the easiest door to photograph. If that condition has not been surveyed, the evaluation remains on hold.

Gate 2 — measure the SLK-9L5-R door fit

These slk 9l5 r door fit notes are a measurement record, not a catalogue transcription. The catalogue’s blank Door fit field means that no fit values can be imported from the supplied record. A complete dimensional drawing checklist must instead connect a dated product source to measurements taken from the actual door.

Record the leaf thickness at the lock position, the usable stile or face-edge width, the opening height, the depth of the stop or frame return and the available projection from the face. Take more than one reading where the surface is uneven, and report the observed range. Do not substitute a nominal door size for the measured condition.

MeasurementCollection methodRequired record
Leaf and stileMeasure at the intended mounting zone and at upper and lower reference pointsThickness and usable width with units
OpeningMeasure clear height and width in the operating positionMinimum available envelope
Stop or frameRecord projection, depth and return directionSection or annotated photograph
Face edgeRecord thickness, profile, coating and available bonding areaCross-section and construction note
Rail or guideRecord the interface around the intended lock positionMarked photograph and measurement
Existing lockRecord centre position, fixing points and spindle or keeper interfaceRemoval and reuse assessment
Mounting zoneMark the proposed panel, case and service areaOverlap and interference overlay

The dimension drawing checklist should also record whether the supplier drawing uses the same measurement convention as the site survey. A missing tolerance, an unexplained zero point or a drawing without door orientation prevents a reliable comparison.

Measure the proposed hardware locations against the door, not against the wall or floor alone. Then add the supplier’s required panel and operating areas to the drawing. If those areas are absent from the supplied record, request them; do not estimate them from the product photographs.

Gate 3 — trace the hardware-to-door interface

The door surface is only one side of the interface. The physical mock-up must show how the escutcheon or panel, lock body or case, latch or bolt drive, strike plate or keeper, spindle, cylinder and any handle or lever relate to the selected leaf.

For a sliding door, the actual connection may involve a rail-mounted case, a face-mounted arrangement or a separate patch fitting. The catalogue description alone does not identify which method applies to a particular leaf, and no patch fitting should be assumed to be included. Ask the supplier to identify the supplied components and their interfaces on a dated drawing.

Interface elementWhat the surveyor recordsEvidence needed to close the check
Escutcheon or panelAvailable surface, projection and overlapSupplier outline placed on the door survey
Lock body or mortise caseCase depth, fixing route and accessSection drawing or physical sample result
Latch or bolt driveTravel, obstruction and meeting-point relationshipAnnotated operating-position photograph
Strike plate or keeperFixing location and frame engagementSupplier or installer interface sketch
Spindle, cylinder and roseCentre position and rotation envelopeExisting-hardware removal and sample record
Handle or leverProjection, grip space and return pathDoor-position test
Existing patch or mounting platePresence, condition and reuse statusMaterial and attachment inspection

“Close enough” is not an interface result. Capture the condition in which the door latches, unlatches, remains at the intended rest position and returns to a repeatable location. Any forced movement or rubbing belongs in the exception register, even if the panel itself fits.

Gate 4 — map operating and service clearances

Sliding door lock clearance includes more than the visible face of the lock. Separate the user approach zone, the movement path of the panel and handle, the door’s travel through the opening and the space needed to inspect or service the installed hardware.

The catalogue records a 3D face method, but it provides no verified recognition distance or approach envelope in the supplied fit block. During face recognition lock installation planning, reserve a proposed standing and approach area for supplier confirmation rather than adopting a remembered sensor range. Measure the area in the real traffic environment and mark any obstruction that could enter that zone.

Clearance zoneSurvey actionFailure indication
User approachMark where a user would stop and present the credential or faceObject, wall return or traffic conflict
Handle and leverFollow the full grip and return movementContact, binding or uneven return
Door travelObserve the leaf through its intended travelPanel or hardware strikes the frame
Latch engagementInspect the meeting point in the closed positionKeeper movement or visible gap
Service accessIdentify access to fasteners, override and power areasComponent cannot be reached safely
Emergency useCheck the route needed to operate mechanical emergency accessAccess is obstructed or poorly identified
Cleaning areaEstablish room for routine surface cleaningRepeated removal or dismantling is implied

If the leaf includes a door closer or hold-open device, record its position and interaction with the proposed panel. These may be site accessories rather than lock components, but they still control the usable envelope.

The output of this gate should be an annotated plan or elevation. Mark actual measurements, not schematic symbols alone, and identify which items came from the supplier and which came from the survey.

Retrofit route — preserve, patch, adapt or replace

A retrofit decision has to follow the door construction, not the desired headline of “reuse existing door.” The Office Smart Lock Site Survey can help structure the office-side inventory, while the comparison below keeps the installation route explicit.

Retrofit routeUse whenRequired evidenceProcurement disposition
Preserve the existing doorThe interface is physically compatible and required zones remain clearDated drawing comparison plus representative sample resultProceed to controlled approval
Preserve with a documented adaptationA defined adapter, patch or relocation can be used without an unresolved conflictAdapter details, attachment method and mock-up resultConditional approval only if the adaptation is named and evidenced
Replace the leaf or panelExisting construction cannot receive the proposed arrangementRemoval scope, replacement specification and site impactRoute to a revised fit package
Replace the lock arrangement while retaining the doorExisting hardware is the only conflict and an alternative mounting method is supportedInterface review and operating testProceed only after the alternative is approved

An adaptation is not automatically lower risk. Moving the lock position may affect the face edge, rail, existing reinforcement or service access. Removing a patch can expose an untreated cavity or leave an opening that needs a defined closure. Every proposed change must return to the relevant measurement and interface gates.

Do not use this fit approval to settle a separate question concerning a door designated for a special code, egress review or other local compliance check. Route that item to the project’s responsible reviewer and obtain the project-specific evidence.

CONFIRM-WITH-LOCAL-BUILDING-REQUIREMENTS

Material, finish and exposure screening

The catalogue record supplies the finishes “Red Bronze / Gunmetal,” but the supplied Door fit and Environment records contain no usable values for this decision. Finish selection therefore cannot be used as evidence of substrate compatibility or operating conditions.

The survey should identify the leaf material, face treatment, track or rail condition, cleaning exposure and any direct weather contact. Where the environment may affect the electronics or moving parts, request the supplier’s documented conditions for the exact SKU. Do not infer a weatherproof housing, temperature range or humidity range from the product category.

For a finished or coated leaf, ask how the proposed mounting method interacts with the coating and whether an exposed area requires treatment. This is a question for the supplier and hardware reviewer, not a promise that a particular preparation method will be accepted. If a physical sample is used, retain photographs of the original surface and the area after test fitting.

Finish samples should be reviewed separately from the fit gate. Agreement on colour does not close a dimensional gap, and a visible mismatch is not evidence of an installation defect.

Credential and control boundary

The SLK-9L5-R catalogue entry lists RFID/IC card, passcode, fingerprint, 3D face, mobile app and mechanical override as standard. Its platform field describes a smart mobile app for remote unlock, temporary passcodes and access records, with functions including remote unlock, temporary or periodic passcodes, user management and access records.

Those functions have a software and credential boundary, not a dimensional one. How Credentials and Management Software Work on SLK-9L5-R covers that boundary separately. During fit review, verify only where the user must present a card, enter a code, use a fingerprint or approach the face-recognition area, plus where the mechanical override must remain reachable.

A software-enabled unlock path cannot compensate for a door that rubs, a latch that does not engage or a service route that has been blocked. Conversely, successful mock-up movement does not prove that credential issuance or remote management is configured. Keep physical fit and control-system acceptance as separate sign-offs.

Gate 5 — run the physical mock-up test

A physical mock-up test is the strongest available evidence for this evaluation, provided it uses the representative door or a full-scale, dimensionally equivalent section and the intended mounting method. A visual comparison of the product beside the door is not a substitute.

Begin with identity and condition photographs. Mark the supplier-defined mounting references, fit the supplied components and record every operation that required alteration. Do not conceal a modification: an improvised hole, bent keeper or relocated case is evidence for the decision, not an installation detail to discard.

Test stepProcedureRecordStop condition
Dry interface checkAlign the supplied case or panel without forcing itOverlay and contact-point photographsParts do not align or need undocumented alteration
Closed-position operationClose the leaf and operate the lock normallyLatch or bolt engagement and gap observationsHardware does not engage consistently
Full-travel operationMove the door through its intended rangePanel, handle and frame interference notesAny contact, binding or obstructed travel
Access-path checkUse each physical credential method in its intended zoneApproach and clearance observationsAccess is blocked or reaches outside the usable area
Override and service checkOperate the mechanical override and access service pointsTool and hand clearance evidenceOverride or service point cannot be used safely
Restoration checkRemove or adjust the sample and inspect the surfaceMarking, damage or finish-change recordUnacceptable damage or an undocumented attachment remains

The project should use the supplier’s stated test method for the SKU and record the result. The supplied catalogue facts do not provide a cycle count or fit-specific operating figure, so none should be invented. Any site-specific acceptance limit should be agreed before the test rather than added after an undesirable result.

Gate 6 — apply the procurement decision matrix

Fit approval should be based on gates, not on a general impression. A passed measurement cannot compensate for a failed physical interface, and a convincing sample cannot compensate for an unidentified SKU. Hard gates should be closed first; then the remaining evidence can support the disposition.

GateApproval evidenceConditional evidenceHold or reject trigger
G0 — Identity and documentsSKU, dated page and drawing revisions reconcileA named document is due with an ownerProduct identity is unresolved
G1 — Door populationVariation has been checked and a representative unit is definedOne door group awaits physical surveyUntested variation is treated as identical
G2 — DimensionsSupplier and site geometry have been comparedA defined field measurement is scheduledNo dimensioned interface exists
G3 — Hardware interfaceComponents align in drawing and sampleAdaptation is documented and being testedSupplied components do not meet the door
G4 — ClearancesUser, movement and service zones are unobstructedOne non-structural access point is under reviewRequired movement or access is blocked
G5 — Mock-upRepresentative operation is satisfactoryA repeat test is required after a named changeThe installation needs undocumented modification
G6 — HandoverEvidence index is complete and exceptions are closedProcurement accepts a bounded outstanding itemApproval would rely on an assumption

A conditional decision must name the outstanding item, owner, evidence required and downstream gate it blocks. It should not transfer the problem through a vague phrase such as “dimensions later.”

The procurement manager may approve the fit input for the evaluation stage while reserving installation approval for the qualified project team. A SLK-9L5-R Order Review: Items to Confirm Before Release is the next control point for keeping fit evidence attached to the order-review process.

Exception and change control

Open an exception whenever new information changes the door, the product evidence or the intended installation method. Typical triggers include a revised drawing, a different leaf delivered to site, a changed rail position, a newly installed cabinet, an altered frame or a sample that required improvised modification.

Exception fieldRequired entry
TriggerThe changed condition and where it was observed
Affected gateThe gate that must be reopened
Evidence impactWhich conclusion is no longer supported
OwnerPerson responsible for closing the item
Required actionMeasurement, drawing, sample or review needed
StatusOpen, in progress, closed or withdrawn

Version every submitted document. When a change closes an exception, retain the superseded evidence and show the replacement. Do not silently overwrite a dimension or remove the failed sample photograph; the sequence is part of the audit trail.

A door replacement does not inherit the approval of the removed door. Likewise, a supplier drawing revision requires at least a targeted overlay and interface check to establish whether the approved sample remains representative.

Evidence pack and evaluation closeout

The procurement handover should contain a short index followed by traceable evidence. Name the package for the project and model, then order the files by gate. Include the door population sheet, site photographs, dimensional overlay, interface drawings, annotated clearance plan, mock-up test record, exception register and final decision page.

The index should identify the source, revision and status of every drawing. Each photograph needs a door reference and orientation marker. Measurements need units and enough context to show where they were taken. Supplier evidence should retain its dated product-page reference, while project evidence should retain the surveyor’s notes and test observations.

Before closing the evaluation, confirm that:

  • The SKU and dated product evidence agree.
  • Every door group has a defined physical basis.
  • Supplier geometry and site measurements use compatible references.
  • The panel, lock case, latch or keeper, handle and service areas have been reviewed.
  • The representative mock-up result is recorded without omitted modifications.
  • Each exception has an owner and a stated effect on approval.
  • The procurement disposition is signed and linked to the relevant doors.
  • Any later order review receives this evidence pack rather than relying on memory.

For the broader field survey, use the Office Smart Lock Site Survey when the project includes office door populations. For the model record behind this runbook, use SLK-9L5-R Specifications, Field by Field alongside the completed fit evidence.

When the disposition is approved or bounded and conditional, send the indexed drawings, dated product-page extract, mock-up record and open-exception summary with the request-a-quote enquiry. The commercial request should identify the exact evidence set, so the supplier can respond to the remaining fit questions without reopening decisions that the project has already closed.

Coșul dumneavoastră
Experiența dumneavoastră pe acest site va fi îmbunătățită dacă permiteți utilizarea cookie-urilor. Politica privind cookie-urile
Chat on WhatsApp