Housing materials and wall thickness buyer understanding: A guide for integrators comparing smart lock housing materials, applicable door thickness, fit.

Publicado el: ago. 21, 2024

Housing Materials and Wall Thickness in a Smart Lock: What a Buyer Should Understand

Housing Materials and Wall Thickness in a Smart Lock: What a Buyer Should Understand

How to read this qualification record

A system integrator needs more than a material name and a single thickness number. This housing materials and wall thickness buyer understanding treats the supplier record as a set of linked fields: construction, dimensions, exposure, and evidence. Smart lock housing materials affect the assembly proposal only when paired with the lock body, door geometry, and selected finish. The purpose is qualification: identify what can be released for a project and what must remain on hold.

Direct answer. Here, wall thickness usually means the door leaf or partition thickness at the lock position. It does not mean the wall thickness of a lock case. For a door mounted through masonry, framing, or a demountable partition

Field annotations for a supplier record

The following sheet separates a supplier statement from an approval condition. Add the source, revision, and project door reference beside every answer. A missing field is not evidence of suitability.

Annotated fieldAnnotation for the integratorEvidence to requestRelease test
Panel/body materialIdentify panel, case, and cover separately rather than grouping them as metal.Material statement tied to the SKU and drawing revision.Matches the selected build and finish.
Applicable door thicknessState the minimum, maximum, and conditions behind the range.Dated product page, dimensional drawing, and installation guide.Measured door range remains inside the envelope.
Lock body/mortiseRecord case type, backset, spindle, latch, and deadbolt arrangement.Dimensioned drawing and cutout template.Geometry matches the door and frame.
Panel dimensionsRecord visible panel and internal case envelopes.Drawing with supplier-stated tolerances.No clash with door, frame, or hardware.
Door frame rebateRecord rebate depth, width, and edge distance.Field template and site measurements.Fixing and latch engagement remain feasible.
Weatherproof housingTreat this as a field to verify against the stated exposure.Scoped evidence or defined limits for the exact build.Project exposure falls inside documented limits.

Material route comparison

For lock body and mortise fit, compare panel and body materials separately rather than treating the entire product as one construction. Each material route changes the evidence required and the details that need control.

Candidate routeBuyer considerationEvidence to requestDecision condition
Stainless steelMay suit exposed-housing proposals where a defined finish and cleanability are priorities.Material designation, finish definition, and dimensional records.Qualify only the documented build.
Zinc alloyMay suit compact cast-case proposals where casting and coating details need definition.Material statement, process note, coating information, and drawings.Qualify after geometry and finish review.
AluminumMay fit enclosure concepts where mass is a design constraint.Alloy designation, fastener-compatibility details, and finish limits.Qualify for the stated assembly only.
Polymer or compositeMay fit non-structural sensor or trim components.Material designation, environmental limits, and cleaning-compatibility evidence.Qualify when documented limits fit.
Hybrid constructionCan assign different materials to different parts, as in the example below.Component-by-component material map and assembly drawing.Trace every part to its source.

These rows are comparison routes, not a universal ranking. A mixed construction may be appropriate, but only a component-level record reveals where the material, finish, and fit constraints apply.

Thickness conditions and fit boundaries

housing materials and wall thickness buyer understanding — project worksheet. Complete a door fit measurement at the latch, hinge, top, and bottom positions, recording minimum and maximum leaf thickness. Add leaf material, reinforcement, rebate, edge distance, backset, swing, and existing hardware. A stated range must be compared with all relevant measurements, not just one convenient thickness reading.

Use one worksheet per door type rather than one record for an entire site. Timber, metal, glass, and composite partitions can share a nominal thickness while presenting different fixing and edge conditions. For glass or patch-fitted doors, request the applicable patch-fitting dimensions rather than extrapolating from a timber door. Where a lock sits on a wall assembly, document the assembly instead of treating its total thickness as door-leaf thickness. The Housing Materials and Wall Thickness and Door Compatibility: The Fit Envelope provides a structured place to record these distinctions.

Qualification decision path

Convert the completed record into a release path:

flowchart TD
    A[Measure the door] --> B[Complete material and dimension fields]
    B --> C{Supplier evidence matches SKU}
    C -->|Yes| D[Compare project conditions]
    C -->|No| E[Hold and request revision]
    D --> F{Documented envelope fits}
    F -->|Yes| G[Release qualified configuration]
    F -->|No| H[Resolve fit or exposure gap]

A missing or conditional answer keeps the configuration on hold until the relevant drawing, measurement, or scoped evidence arrives. A favorable material description cannot close an unresolved geometry field.

Worked annotation for a hotel-lock record

The supplied first-party record for the SLK-9936S hotel lock lists a 36–100 mm door-thickness range and a stainless steel + alloy body; it also identifies a 5-pin cylinder and 3-point latch. Annotation: this is a supplier example, not a universal fit rule. Confirm on the dated product page for the specific SKU, and obtain the dimensioned installation documents before approving it.

The same question is worked through in more detail in the sl 6301 office application. That is the same question housing materials and wall thickness buyer understanding has to answer here.That record does not, by itself, establish panel dimensions, backset, rebate, spindle geometry, or finish suitability. The buyer should enter those as open fields and compare them with the measured door. The model is useful as a data-format example: it shows what a complete hotel-lock record should say while leaving project-specific fit unresolved.

For the measurement side of this, see narrow edge locks for office doors. That is the same question housing materials and wall thickness buyer understanding has to answer here.

Evidence package and release status

Material evidence request. Ask for a material statement tied to the SKU and drawing revision, dimensional drawings, an installation guide, supplier-stated tolerances, a finish definition, relevant exposure evidence for the exact configuration, and a proposed change-control process for revisions or substitutions. Request documentation: dimension drawings, installation guide, datasheet on request. Each document must identify the build being quoted. The Specifying Housing Materials and Wall Thickness: Questions that Get Real Engineering Answers helps turn these requests into supplier questions.

Use a three-state release table rather than a vague approved label:

StatusUse when
QualifiedSupplier evidence, drawings, and project measurements agree, and every open field is closed.
HoldA field is missing, conditional, linked to another revision, or awaiting site data.
ReworkThe measured door falls outside the envelope, geometry conflicts, or the selected build lacks required evidence.

Related reading and next action

Use Housing Materials and Wall Thickness Trade-Offs: Cost, Durability and Service to compare the consequences of material and construction choices. An Office Smart Lock Site Survey can add site context to the qualification record.

When the annotations, measurements, and supporting documents agree, submit the specific SKU and configuration through the request a quote workflow. That gives the supplier a defined package to evaluate rather than an open-ended request based only on a material name and thickness range.

Su carrito
Su experiencia en este sitio mejorará al permitir cookies Política de cookies
Chat on WhatsApp