The buyer who treats smart lock vs magnetic door lock as a single question — 'which one is better?' — answers the wrong question.

Veröffentlicht am: Mai 22, 2026

Smart Lock vs Magnetic Door Lock

Smart Lock vs Magnetic Door Lock: A Five-Pillar Decision Frame

A smart lock in this catalog is a battery- or mains-powered electromechanical lock whose electronic credential reader (PIN, RFID, fingerprint, mobile credential, mechanical key) commands a mechanical latch, deadbolt or mortise to engage or release — a magnetic door lock ("maglock") by contrast is a wall- or door-frame-mounted electromagnetic device that holds a steel strike plate against the door only while continuous electrical current is flowing through the coil. The two technologies look interchangeable from the corridor side because both can unlock on a credential signal; they are not interchangeable once the door is examined. They differ on whether the door is locked when the power fails, on whether the lock can be credentialed at all without an external controller, on what the door has to look like behind the face plate, on what the local fire and life-safety authority will accept, and on what the facility pays to install, run and replace them across a five-year horizon.

This article is a decision-pillar explainer — not a comparison matrix, not a product datasheet. It frames the smart-lock-vs-maglock question as five pillars the buyer has to settle before a single SKU is shortlisted, and inside each pillar it names the failure pattern the pillar prevents, the decision the buyer must make, and the cells that have to come back from the supplier as to verify in writing confirmation rather than a brochure number.

Catalog position. The 79-model factory range covers electromechanical smart locks across hotel, residential, commercial, outdoor, glass and cabinet applications. A magnetic door lock (maglock / electromagnetic lock) is not a published category in this catalog — every reference to a magnetic lock in this article is the buyer-side reference design the buyer is comparing against, not a SKU that can be quoted. Every shortlisted smart-lock SKU in this comparison still routes to check the model’s published specification for door-prep envelope, power source, battery cycle figure, credential stack, fail-state policy and any local code-compliance posture.

Distinct from three siblings in the same cluster: Smart Lock vs Electric Strike covers the lock-side vs strike-side comparison — electric strike replaces a strike plate, not the lock itself; this article covers the lock-side vs an entirely different locking technology (electromagnetic hold). Smart Lock vs Access Control Reader covers the lock-side vs the credential-side — access control reader is the front-end the smart lock already contains; this article covers the lock-side vs an architecture where the credential lives on a separate controller that drives an electromagnetic hold. Smart Lock vs Traditional Hotel Lock is the hotel-line head-to-head on credential cadence and audit workflow and treats the maglock as a separate category entirely — the four articles together are the C15 quartet on lock-side, credential-side, door-side and electromagnetic-hold comparisons.

Why this is a decision frame and not a comparison matrix

The buyer who treats smart lock vs magnetic door lock as a single question — "which one is better?" — answers the wrong question. The right question is five questions, in order, and the answer to the first often pre-decides the second and the fourth. Most smart-lock-vs-maglock mistakes are made by skipping a pillar. A distributor specifies a maglock because "it's stronger" and forgets Pillar 2 — the door unlocks on power loss, and the building has a fire code that forbids that failure mode. A property manager specifies a smart lock because "it's credentialed" and forgets Pillar 1 — the credentialed smart lock is mechanical and self-contained, while the maglock is a credentialed lock plus a coil plus a power supply plus a request-to-exit device plus a fire-interface relay, none of which are inside the lock body. The five pillars are program discipline. Use them in order.

Pillar 1 — Locking Mechanism Anatomy: What Actually Holds the Door Closed

The smart-lock-vs-maglock decision starts with what physically resists the door. A smart lock in this catalog resists the door with a mechanical element — a latch, a deadbolt, a mortise latch or a 3-point latch with a credential-driven actuator. The credential commands an actuator that engages or releases the mechanical element; the mechanical element is what physically stops the door. Power can fail and the door stays locked (on fail-secure SKUs) or unlocks (on fail-safe SKUs — check the model’s published specification which mode the shortlisted SKU implements and at which authority this has been certified for the local jurisdiction).

A magnetic door lock resists the door with electromagnetic force only. A coil in the lock body is energized continuously; an armature plate on the door is pulled against the coil by the magnetic field; the door is held in the frame by that magnetic field alone. The moment the coil is de-energized — by power loss, by a fire relay, by an exit button — the magnetic field collapses and the door is released. There is no mechanical element holding the door. This is the first architectural difference and the one every other pillar inherits.

Three architectural realities matter:

  • The smart lock carries its own security inside the door. The mechanical element, the actuator, the electronics and the credential reader all sit on or in the door. Removing the door from the frame (or cutting through the door) does not give an attacker a bypass the way cutting power to a maglock gives a bypass.
  • The maglock is a powered hold-down, not a lock. A magnetic door lock is an electromagnetic hold-down device with credential-driven release; it is a category of access-controlled hardware, not a lock in the same mechanical sense. The credential is upstream of the controller; the controller is upstream of the coil; the coil is upstream of the door. Cut any link — power, controller signal, credential — and the door is released.
  • The combination is the most common operating configuration for high-traffic public doors. Many commercial programs run a smart lock on the room-side doors (hotel guest rooms, apartment unit doors) and a maglock on the perimeter-side doors (lobby, garage, stairwell release, after-hours suite). The two technologies are not mutually exclusive on a property; they are mutually exclusive on a door.

The decision-pillar rule for Pillar 1 is: the locking mechanism decides what the door has to look like and how it has to be powered, before any credential is chosen. A buyer who picks a maglock because "it's stronger" without first deciding whether the door is allowed to release on power loss is choosing a credentialing surface (Pillar 3) and a code-compliance posture (Pillar 4) by accident. The lock-side architecture has to come first.

Locking mechanismWhere the security livesWhat fails firstWhat stays locked on power lossTypical door profile
Smart lock (mechanical element + actuator + credential)Inside the door body and credential readerCredential reader, actuator or battery on fail-secure SKUs — door stays lockedYes, on fail-secure SKUs — check the model’s published specificationHotel guest room, apartment unit, office suite, IT room, retail stockroom
Magnetic door lock (electromagnetic hold + controller + credential)In the coil, the controller and the power supplyPower, controller or credential signal — door releasesNo — the door releases on power loss by designLobby, garage entry, after-hours suite, stairwell release, internal perimeter
Combination (smart lock on room side + maglock on perimeter side)Mechanical on the door; magnetic on the frameEither link in the chainPer-door — not per-propertyHotel / apartment building / commercial floor

Pillar 2 — Power and Fail-State Policy: What Happens When the Power Drops

The single most important difference between a smart lock and a magnetic door lock is the fail-state policy. A smart lock, on a fail-secure SKU, stays locked when the power drops; a magnetic door lock releases the door when the power drops. This is not a tweakable detail. It is the architectural principle. A maglock cannot be made to stay locked on power loss without an uninterruptible power supply (UPS) backing the coil — and even then, the UPS is a battery, and the battery will eventually die. The fail-state policy is upstream of the UPS.

Three fail-state profiles matter for a commercial door:

  • Fail-secure (locked on power loss). The door stays locked when power drops. Power returns and the door is still locked, the credential still works, the audit trail still records. This is the typical posture for a hotel guest room, an apartment unit, an office suite, an IT room, a document store. The smart-lock line in this catalog generally offers fail-secure SKUs — check the model’s published specification for each shortlisted SKU which mode is implemented. The maglock cannot offer this posture without an UPS that is itself backed and tested.
  • Fail-safe (released on power loss). The door releases when power drops. This is the typical posture for an egress door, a lobby door, a stairwell release, an area of refuge door. The reason is life-safety: in a fire or a power outage, the door must let people out (and, in many jurisdictions, must let first responders in). The maglock is fail-safe by design. The smart lock, where it is required to be fail-safe for an egress door, has to be a fail-safe SKU — check the model’s published specification.
  • Dual-mode (configurable per door). Some smart locks support a configurable fail-state — fail-secure by default, fail-safe when wired to a fire relay or a request-to-exit button. This is a small but real category. Check the model’s published specification whether the SKU supports dual-mode, what the wiring interface is, and what the local AHJ has accepted.

The decision-pillar rule for Pillar 2 is: the fail-state policy is set by the building and the AHJ, not by the buyer. A perimeter door that the local fire code requires to release on power loss will not be approved by the AHJ with a fail-secure smart lock (and a maglock is the standard answer here, with a fire relay). A hotel guest room that requires the door to stay locked on power loss will not pass the property's insurance profile with a maglock (and a fail-secure smart lock is the answer here). The two technologies are not interchangeable, and they are not equivalent under the same code.

Fail-state profileSmart-lock postureMaglock postureWhere each is appropriateWhere each is forbidden
Fail-secure (locked on power loss)Natural posture for fail-secure SKUs in the catalog — check the model’s published specificationNot achievable without a tested UPS — typical AHJ posture is to disallowHotel guest room, apartment unit, office suite, IT room, document store, retail stockroomEgress door under most jurisdictions' fire codes
Fail-safe (released on power loss)Achievable on fail-safe SKUs or via fire-relay wiring — check the model’s published specificationNatural posture by design — coil de-energizesEgress door, lobby, stairwell release, area of refugeHotel guest room, apartment unit, document store under most insurance profiles
Dual-mode (configurable per door)Achievable on dual-mode SKUs with fire-relay wiring — check the model’s published specificationNot applicable — maglock is always fail-safeMixed-use doors where code requires a fire relayPerimeter door where the AHJ has not accepted the dual-mode SKU

Pillar 3 — Credentialing Surface: What the Credential Has to Do and What the Audit Has to Do

The smart-lock-vs-maglock decision then turns on what the credential has to do and what the audit event has to do. A smart lock in this catalog carries its own credential stack — the credential is presented to a reader on the door, the reader validates the credential against the lock-local or platform-side database, the actuator responds, the audit event is recorded at the lock or pushed to a platform. The lock is the integration point: credential, validator, actuator and audit live in one device.

A magnetic door lock carries none of those functions. The credential is presented to a reader (the reader is a separate device — keypad, card reader, biometric reader, mobile reader), the reader validates against a controller (also separate), the controller drives a power supply that energizes or de-energizes the coil, and the audit event is recorded by the controller, not the lock. The maglock is the end of the chain, not the integration point. The integration lives in the controller.

Three credentialing profiles matter:

  • Self-contained credentialing on the door. PIN, RFID, fingerprint, mobile credential — whatever the smart lock reads, the smart lock validates, the smart lock actuates, and the smart lock audits. This is the architecture the catalog smart-lock line is designed for. The lock is the integration point. Adding a controller on top (typical for a maglock) is over-spec.
  • Controller-mediated credentialing. Card reader at the door, controller in the IT closet, maglock on the frame, request-to-exit button at the desk, fire-interface relay at the panel. The credential is presented to the reader, the reader validates against the controller, the controller drives the power supply, the coil releases. The audit event is recorded by the controller. This is the architecture a maglock is designed for. Replacing the controller-side reader with a self-contained smart lock simplifies the chain — and removes the controller's role, which may be a feature (no controller maintenance) or a regression (no multi-door audit aggregation).
  • Platform-mediated credentialing at scale. Hotel property management system (PMS), serviced-apartment tenant platform, multi-tenant building access platform — the credential is issued and revoked by the platform, and the door resolves it through whatever local architecture exists. A smart-lock SKU with platform-side integration (e.g. one of the hotel-locks SKUs with hotel PC software in standalone or centralized database modes) handles this natively. A maglock requires a controller that speaks to the platform — and the controller is outside the catalog.

The decision-pillar rule for Pillar 3 is: the credentialing surface names the technology, not the brand. A single door with one credential type and no central audit requirement is a self-contained smart lock; the maglock is over-spec even if the door is allowed to release on power loss, because the credential stack inside the controller is not earning its cost. A multi-door property with platform-side credentialing and centralized audit is a controller-mediated architecture — a maglock can be the right answer for the perimeter doors, a smart lock for the room-side doors, and the controller is the integration point that ties them together. The two technologies are not interchangeable, but they can be complementary on the same property.

Credentialing surfaceSmart-lock fitMaglock fitDecision rule
Self-contained credentialing on the door (one door, one credential type, no central audit)Natural fit — lock is the integration pointOver-spec — controller is not earning its costSmart lock; confirm credential stack on the product page
Controller-mediated credentialing (multi-door, central audit, mixed credential types)Achievable via platform-class smart locks — check the model’s published specificationNatural fit — controller is the integration pointMaglock for perimeter if fail-safe is required; smart lock for room-side if fail-secure is required
Platform-mediated credentialing at scale (hotel PMS, multi-tenant platform, multi-property)Achievable via hotel-locks SKUs with hotel PC softwareRequires a controller that speaks to the platform — controller is outside the catalogSmart lock on room-side doors; maglock on perimeter doors where fail-safe is code-required
Egress-only (door must release on power loss, no audit obligation)Achievable on fail-safe smart-lock SKUs — check the model’s published specificationNatural fit — fail-safe by designMaglock for high-traffic egress; smart lock for low-traffic egress where audit is desired

Pillar 4 — Door Profile, Egress, and Code Compliance: What the Door Has to Look Like

The smart-lock-vs-maglock decision then turns on what the door has to look like and what the local authority having jurisdiction (AHJ) will accept. A smart lock in this catalog fits the door's existing preparation (or a documented retrofit preparation): a cylindrical bore, a mortise cavity, an edge-mount box, a glass-door clamp. The mechanical element integrates into the door; the credential reader integrates into the face plate. Check the model’s published specification for door-thickness envelope, backset, mortise/cylindrical/rim class, handle/latch geometry and strike geometry on every shortlisted SKU.

A magnetic door lock requires a door that can hold an armature plate, a frame or header that can hold a coil, a power supply routed to the coil (often via a low-voltage cable run), and a fire-interface relay at the fire panel. The door is rarely modified mechanically for the maglock itself; the frame or header is. The door prep is on the architecture side, not the lock side.

Four door-and-code profiles matter:

  • Existing door, retrofit preparation possible. A retrofit cylindrical or mortise smart lock fits the existing door prep, or a documented retrofit door prep covers the new SKU. Check the model’s published specification that the SKU's door-prep envelope matches the existing door. The maglock requires a frame or header mount for the coil and an armature plate on the door — out of scope for a no-modification retrofit in most cases.
  • New door or new construction. A smart lock fits the door's specified door prep. A maglock fits the frame or header spec. Both are specifiable on a new build; the choice is driven by Pillar 2 (fail-state), not by door fit.
  • Egress door under fire code. The door must release on power loss. The maglock with a fire relay is the standard solution. The smart lock in fail-safe mode with a fire-relay interface is an alternative where the AHJ has accepted it — check the model’s published specification and at the AHJ. The smart lock in fail-secure mode will not be accepted by the AHJ for an egress door in most jurisdictions.
  • Insurance-rated door (e.g. hotel guest room, document store). The door must stay locked on power loss to satisfy the insurance profile. The smart lock in fail-secure mode is the standard solution. The maglock will not be accepted by the insurer in most cases — confirm with the insurer and the AHJ before specifying a maglock on an insurance-rated door.

The decision-pillar rule for Pillar 4 is: the door profile and the AHJ decide the technology before the SKU does. A commercial program that has both egress doors and insurance-rated doors will use both technologies on the property — maglock for the egress doors with a fire relay, smart lock for the insurance-rated doors in fail-secure mode. A program that has only egress doors will use maglocks (with the right fire interface). A program that has only insurance-rated doors will use smart locks in fail-secure mode. The technology follows the door and the code, not the other way around.

Door / code profileSmart-lock fitMaglock fitDecision rule
Existing door, retrofit prep possibleNatural fit — check the model’s published specificationFrame or header mount required; rarely a no-mod retrofitSmart lock is the default answer on a retrofit; maglock only on a frame-mountable door
New door or new constructionFits the specified door prepFits the specified frame or headerPillar 2 (fail-state) is the deciding pillar, not the door
Egress door under fire codeFail-safe SKUs with fire relay — check the model’s published specification and at the AHJNatural fit with fire relayMaglock is the standard answer; smart lock only where AHJ has accepted a fail-safe SKU
Insurance-rated door (hotel guest room, apartment unit, document store)Natural fit on fail-secure SKUsMaglock will not satisfy the insurance profile in most casesSmart lock in fail-secure mode — check the model’s published specification
Glass door or specialty door (no mortise possible)Glass-door smart lock — check the model’s published specificationMaglock on a glass door is feasible with a glass-door armature bracketGlass-door smart lock is the default; maglock only on frames that accept a coil mount
Outdoor / gate doorOutdoor/aluminum-door-class smart lock — check the model’s published specificationMaglock on a gate is feasible with a weather-rated coilSmart lock is the default on outdoor doors; maglock only where the gate exposes no credential surface

Pillar 5 — Total Lifecycle Cost: What This Costs Over Five Years

The smart-lock-vs-maglock decision finally turns on cost — not the unit price of the lock body (which is the question that gets asked first and the one that matters least), but the five-year cost of the architecture. A smart-lock architecture has the lock cost, the credential enrollment, the per-door installation cost, the battery-replacement labor across five years, the platform cost if any, and the SKU refresh cadence. A maglock architecture has the lock cost, the power supply cost, the controller cost, the reader cost, the request-to-exit cost, the fire-relay cost, the install labor for the cable run, the UPS cost if fail-secure behavior is required, and the per-door commissioning labor.

The cost structure the buyer has to model — not assert as a number — is:

  • Per-door lock cost. The lock body or maglock coil — check the model’s published specification per shortlisted SKU; no published price exists.
  • Per-door accessory cost. For a smart lock: any external controller, gateway or relay required for the credential workflow. For a maglock: the controller, the reader, the request-to-exit, the fire-relay, the power supply. Confirm with the supplier; no published MOQ exists.
  • Per-door install labor. For a smart lock: the door-prep labor and the wiring if any. For a maglock: the cable-run labor, the frame or header prep, the power-supply mounting and the fire-relay wiring — typically substantially more than a smart-lock install. Confirm with the installer; this is a per-property figure.
  • Per-door battery / power cost. For a smart lock (where battery-powered): the battery replacement cadence (the SLK-9936S hotel-class spec block quotes battery operating cycles >15,000 for that SKU; siblings route to the product page for the per-SKU figure). For a maglock: the continuous power draw, the power-supply replacement and the UPS replacement if any. Check the model’s published specification per SKU; maglock power draw figures route to the supplier.
  • Per-deal figure envelope. Unit price, MOQ, lead time, warranty years, payment terms, install crew availability — confirm with the supplier via /request-a-quote; no published numbers exist anywhere.

The decision-pillar rule for Pillar 5 is: the technology is decided by Pillars 1 through 4 first; the cost pillar confirms the choice. A buyer who has an egress door under fire code (Pillar 4) cannot save their way back to a smart lock by quoting a lower maglock price — the AHJ posture is the deciding pillar. A buyer who has an insurance-rated door (Pillar 4) cannot save their way back to a maglock by quoting a lower smart-lock price — the insurance profile is the deciding pillar. The cost pillar is the confirmation of the technology, not the deciding factor.

Lifecycle cost driverSmart-lock positionMaglock positionDecision rule
Per-door lock costSingle device body — check the model’s published specificationSingle device body — confirm with the supplierComparable on a unit basis; the accessories diverge
Per-door accessory costExternal controller or gateway only if a platform workflow is required — confirm with the supplierController, reader, request-to-exit, fire-relay, power supply — all requiredMaglock accessories are the dominant accessory line; maglock without the accessories does not work
Per-door install laborDoor-prep labor and minimal wiring on most SKUs — check the model’s published specificationCable run, frame prep, power-supply mounting, fire-relay wiring — typically higherMaglock install labor is the dominant install line — confirm with the installer per property
Per-door battery / power costBattery cycle figure on the relevant SKU (SLK-9936S quotes >15,000 cycles for that SKU only; siblings route to the product page)Continuous power draw, power-supply and UPS replacement — confirm with the supplierBattery labor on a smart lock is real; maglock power supply is real and continuous
Per-deal figure envelopeRouted to /request-a-quote per SKURouted to /request-a-quote per supplierNo published price / MOQ / lead time / warranty year exists; do not invent one

The Five Pillars as a Decision Stack

The five pillars do not run in parallel. They run in order, and Pillar 1 sets the question for Pillar 2, which sets the question for Pillar 3, which sets the question for Pillar 4, which sets the question for Pillar 5. A program that respects the stack arrives at a per-door technology answer (smart lock, maglock, or both on the same property), not a "let's see what the supplier has" answer.

PillarQuestion the pillar forcesDefault if the pillar is skipped
1 — Locking Mechanism AnatomyWhat physically resists the door — a mechanical element, an electromagnetic hold, or both?Maglock on an insurance-rated door — silent failure at the first door breach
2 — Power and Fail-State PolicyDoes the door have to stay locked or release on power loss?Fail-secure smart lock on an egress door — silent failure at AHJ inspection
3 — Credentialing SurfaceWhere does the credential live, and what does the audit obligation look like?Maglock on a single-credential self-contained door — controller is over-spec
4 — Door Profile and Code ComplianceWhat does the AHJ accept, and what does the door's prep envelope support?Smart lock on a fire-rated door without a fire relay — silent failure at fire inspection
5 — Total Lifecycle CostWhat does the architecture cost over five years, including accessories and install labor?Cost pillar used to override an operational pillar answer — silent failure at the first code or insurance challenge

Consider a 240-Door Mixed-Use Property

A 240-door mixed-use property — twenty floors, eight floors of a chain hotel (160 guest room doors), four floors of serviced apartments (80 unit doors), ground-floor retail (four stockroom doors, two lobby doors), and a basement plant room with two mechanical-room doors — illustrates how the five pillars work together.

  • Pillar 1. 160 hotel room doors and 80 apartment unit doors need mechanical hold-down (credentialed lock body), not electromagnetic hold. Four retail stockroom doors need mechanical hold-down plus audit. Two lobby doors can be either — the chain prefers credentialed mechanical hold-down with audit push, the property prefers electromagnetic hold-down on the lobby for after-hours remote release. Two basement mechanical-room doors need mechanical hold-down, fail-secure posture, audit.
  • Pillar 2. Hotel guest room doors must be fail-secure (insurance profile). Apartment unit doors must be fail-secure (insurance profile). Retail stockroom doors must be fail-secure (insurance profile). Lobby doors must be fail-safe (egress profile, fire code). Mechanical-room doors must be fail-secure with audit. Five fail-state profiles in one building — and only one of them (lobby) is the maglock's natural fit.
  • Pillar 3. Hotel rooms use hotel PC software in centralized database modes (the SLK-9936S hotel-class first-party spec block quotes standalone or centralized database modes for that SKU; siblings route to the product page). Apartment units use a tenant platform push. Retail stockrooms use a single-credential self-contained workflow. Lobbies use a controller-mediated credentialing workflow that ties to the after-hours remote release. Mechanical rooms use a self-contained mechanical-key plus credential workflow. Five credentialing profiles — and only the lobby is the maglock's natural fit.
  • Pillar 4. Every hotel, apartment and stockroom door is insurance-rated: the AHJ has accepted a fail-secure mechanical lock. The lobby is an egress door under fire code: the AHJ has accepted a maglock with a fire-relay interface. The mechanical-room doors are not egress: the AHJ accepts a fail-secure mechanical lock with audit. The building has three AHJ postures in one building — and only the lobby requires a maglock.
  • Pillar 5. A maglock architecture across the whole building would violate Pillar 2 (insurance-rated doors) and Pillar 4 (AHJ posture) on 246 of the 248 doors. A smart-lock architecture across the whole building would not satisfy the lobby's fail-safe requirement. The mixed architecture — smart lock on 246 doors, maglock on 2 lobby doors — is the only architecture that survives all five pillars. The cost pillar confirms the operational pillars rather than overriding them.

The decision is not "smart lock or maglock" for the building. It is a mixed deployment: smart-lock SKUs (with fail-secure posture, mechanical hold-down, platform-side audit where required — check the model’s published specification) on 246 doors; maglock SKUs (with fire-relay interface, controller-mediated credentialing, fail-safe posture) on the 2 lobby doors. The five pillars did not produce a single answer. They produced a program answer — different technologies for different doors, with the per-door and per-SKU confirmation discipline enforced at every door.

This is an illustrative scenario, not a customer story. The names, the door counts, the technology choices and the failure modes are a worked example; nothing here is asserted as a real customer outcome or as a per-SKU capability. No customer name, no project value, no outcome metric is asserted anywhere.

RFQ Worksheet — Five Lines the Smart-Lock-vs-Maglock Spec Must Carry

The RFQ for a smart-lock-vs-maglock program has to carry five lines, one per pillar, each in the form the supplier can answer against a specific door or SKU. Cells marked to verify in writing are intentionally blank: those numbers must come from the per-SKU product page, from the local AHJ or from the installer, not from this article. The worksheet is the artefact the buyer pastes into the RFQ template.

#LineSmart-lock answer (catalog position)Maglock answer (reference design — not a catalog SKU)
1Pillar 1 — Locking mechanism per doorMechanical-element + electronic credential per door — check the model’s published specificationElectromagnetic hold + controller + reader per perimeter door — confirm with the supplier
2Pillar 2 — Fail-state policy per doorFail-secure (locked on power loss) on most catalog SKUs — check the model’s published specification. Fail-safe on egress doors — check the model’s published specification and at the AHJFail-safe (released on power loss) by design; UPS-backed if fail-secure behavior is required — confirm with the supplier and the AHJ
3Pillar 3 — Credentialing surface per doorSelf-contained credential stack on most catalog SKUs; hotel PC software on the hotel-locks line — check the model’s published specificationController-mediated reader at the door; controller is upstream of the coil — confirm with the supplier
4Pillar 4 — Door profile and code compliance per doorDoor-prep envelope, fire rating, insurance profile per door — check the model’s published specification and at the AHJFrame or header envelope, fire-relay interface, insurance posture — confirm with the installer and the AHJ
5Pillar 5 — Lifecycle cost envelopePer-door lock cost — to verify in writing via /request-a-quote; battery cycle figure per SKU — Check the model’s published specificationPer-door lock / controller / reader / power-supply / fire-relay cost — to verify in writing via /request-a-quote; continuous power draw — confirm with the supplier

Decision Matrix — When Each Pillar Pushes the Technology

The matrix below maps seven common commercial-door situations to the pillar that decides the technology for each. Use it as a starting position, not as the answer; every shortlisted SKU still is checked against the model’s published specification and the local AHJ.

Commercial-door situationPillar that decidesDefault technologyOverride to watch for
Hotel guest room door, fail-secure, platform-side auditPillar 2 (fail-secure) + Pillar 4 (insurance profile) + Pillar 3 (platform-mediated)Smart lock (hotel-locks line — check the model’s published specification)Maglock not a real option under most insurance profiles
Apartment unit door, fail-secure, tenant platformPillar 2 (fail-secure) + Pillar 4 (insurance profile)Smart lock (check the model’s published specification)Maglock not a real option under most insurance profiles
Office suite door, fail-secure, small credentialed populationPillar 2 (fail-secure) + Pillar 3 (self-contained credentialing)Smart lock (check the model’s published specification)None unless Pillar 4 forces a fire relay
Lobby door, fail-safe under fire code, controller-mediated credentialingPillar 2 (fail-safe) + Pillar 4 (egress)Maglock with fire-relay interface — confirm with the supplier and the AHJSmart lock only where the AHJ has accepted a fail-safe SKU
Stairwell release, fail-safe under fire codePillar 2 (fail-safe) + Pillar 4 (egress)Maglock with fire-relay interface — confirm with the supplier and the AHJSmart lock in fail-safe mode where the AHJ has accepted it
Mechanical-room door, fail-secure, audit requiredPillar 2 (fail-secure) + Pillar 3 (audit obligation)Smart lock with audit (check the model’s published specification)None — maglock is over-spec
Garage entry, fail-safe with after-hours remote releasePillar 2 (fail-safe) + Pillar 3 (controller-mediated)Maglock with controller and reader — confirm with the supplierSmart lock in fail-safe mode where the AHJ has accepted it and the workflow is credentialed

Failure Patterns the Five Pillars Catch

The five pillars are not the same five questions as the supplier's brochure. They are the five questions the brochure does not answer.

  • Pillar 1 catches "the brochure said maglock" applied to an insurance-rated door. The brochure says "1,200-lb holding force"; the door is a hotel guest room under an insurance profile that requires the door to stay locked on power loss. The maglock cannot satisfy the insurance profile without a tested UPS, and even the UPS will eventually die. The smart lock in fail-secure mode is the honest answer.
  • Pillar 2 catches "smart lock on a fire-rated egress door" without a fire-relay interface. The fire rating requires the door to release on power loss; the smart lock is fail-secure by default. The fire relay is missing; the door fails closed during the first fire-drill power-down. The maglock with a fire-relay interface is the honest answer.
  • Pillar 3 catches "maglock on a single-credential self-contained door." The maglock needs a controller, a reader, a fire relay, a power supply and a request-to-exit for one credential and one audit requirement that does not exist. The smart lock with a self-contained credential stack is the operationally honest answer.
  • Pillar 4 catches "maglock on a glass door with no frame." The maglock requires a frame or header to mount the coil; the glass door has no frame. The smart lock in the glass-door class (with the door-prep envelope confirmed on the product page) is the honest answer.
  • Pillar 5 catches "we picked the technology on unit price." The unit price is the smallest line on the five-year model. The accessories (controller / reader / fire-relay / power supply), the install labor (cable run / frame prep / power-supply mounting), and the ongoing power draw dominate the cost comparison for a maglock. The battery-replacement labor and the credential enrollment dominate the cost comparison for a smart lock at scale.

How to Brief Your Supplier Using These Pillars

The supplier conversation should be structured pillar-by-pillar, not technology-by-technology. The five lines the supplier must answer — and the cells they must return as to verify in writing confirmation rather than a brochure number — are the same five lines as the RFQ worksheet above. The supplier should not be asked "do you have a maglock?" — they should be asked "for the perimeter doors that the AHJ posture requires to release on power loss, what is the maglock reference design that meets Pillar 2 and Pillar 4, and on what power-supply and fire-relay interface?" The supplier should not be asked "what is your price?" — they should be asked "what factors drive the per-door lock cost, the controller / reader / fire-relay cost if any, and the power-supply replacement cadence?" Every per-deal figure routes to request a quote and to order samples for the pilot.

Catalog position (repeated, because it is the load-bearing rule). The 79-model factory range covers electromechanical smart locks across hotel, residential, commercial, outdoor, glass and cabinet applications. A magnetic door lock (maglock / electromagnetic lock) is not a published category in this catalog — every reference to a magnetic lock in this article is the buyer-side reference design the buyer is comparing against, not a SKU that can be quoted. Every shortlisted smart-lock SKU in this comparison still routes to check the model’s published specification for door-prep envelope, power source, battery cycle figure, credential stack, fail-state policy and any local code-compliance posture. Bluetooth capability is confirmed at the catalog-class level for the classes that pair with TTLock / Tuya apps. Out-of-catalog radios (Matter, Zigbee, Apple Home Key, UWB) are not in the catalog and must not be claimed for any model.

Hotel-line SKUs the Program Will Touch — Model specification check

For hotel-class and adjacent commercial doors the program will shortlist, every per-model spec is routed to the dated product page. The SLK-9936S hotel-class first-party spec block — door thickness 36–100 mm · RFID Mifare 1 @ 13.56 MHz · read distance 0–5 cm · read time <0.25 s · 4 × AA power · battery operating cycles >15,000 · audit/event records up to 1,000 · 5-pin cylinder · 3-point latch · stainless steel + alloy body · multiple finish options · mechanical emergency access · multilingual management software · standalone or centralized database modes · positioned for 1–5 star hotels — is the documentation-granularity anchor for what a per-SKU spec block looks like in writing. It is scoped strictly to that SKU. Do not port these figures across siblings — SLK-9936G / SLK-9905A / SLK-9951TH / SLK-9962S / SLK-G200 / SLK-8831 / SLK-1104 class / SLK-3108 / cylindrical Tuya round-code / 3D-face-recognition remote-intercom / B09 / outdoor D11-D12-D15-ODS-DQ / face 9L5-R-Q7-Future 1 / camera 516 cat-eye / Q7 intercom / 4G / cabinet 6-model family / RFTC-RF card-and-code 118-118E-228-230-232-238-239-253-305-306-308-309-502-620-621-911-002-019-022-2020-760 (stainless options for 019 / 022 / 309). Every sibling spec — door thickness envelope, RFID frequency, read distance, read time, power source, battery cycle ceiling, audit buffer depth, cylinder profile, latch configuration, body material, finish options, mechanical emergency access, app-platform binding, firmware cadence, audit push cadence, multi-property scope, fail-state policy — routes to check the model’s published specification. No porting.

Closing the Loop — From the Five Pillars to the RFQ

The five pillars run in order: locking mechanism (Pillar 1), power and fail-state policy (Pillar 2), credentialing surface (Pillar 3), door profile and code compliance (Pillar 4), total lifecycle cost (Pillar 5). They produce a per-door technology answer, not a per-building one. They produce a per-SKU confirmation discipline, not a brochure acceptance. They produce a to verify in writing worksheet, not a confident number.

Three siblings in the same cluster carry the work forward. Smart Lock vs Electric Strike is the lock-side vs strike-side head-to-head — it picks up the smart-lock side of this article and tests whether replacing the strike plate with an electric strike is a viable alternative to replacing the lock body. Smart Lock vs Access Control Reader is the lock-side vs credential-side head-to-head — it picks up the controller-mediated credentialing surface from Pillar 3 of this article and tests whether the reader is the bottleneck. Smart Lock vs Traditional Hotel Lock is the hotel-line head-to-head on credential cadence and audit workflow — the four articles together form the C15 quartet on lock-side, credential-side, door-side and electromagnetic-hold comparisons.

Run the five pillars. Paste the RFQ worksheet. Confirm every per-SKU cell on the dated product page. Confirm every code-compliance and AHJ cell at the local authority. Route every per-deal figure — price, MOQ, lead time, warranty year, accessory cost, install labor — to request a quote and to order samples for the pilot. The technology is downstream of the door, the code, the workflow and the resilience profile, not upstream of them. Decide the technology before the SKU; do not let the SKU decide the technology.

Ihr Warenkorb
Ihre Erfahrung auf dieser Website wird verbessert, wenn Sie Cookies zulassen. Cookie-Richtlinie
Chat on WhatsApp