A smart lock hole coverage guide is the annotated datasheet a buyer reads when the question is not will the new lock fit the existing cut-outs — that

Offentliggjort den: nov. 03, 2026

Smart Lock Hole Coverage Guide

Smart Lock Hole Coverage Guide

A smart lock hole coverage guide is the annotated datasheet a buyer reads when the question is not "will the new lock fit the existing cut-outs" — that question belongs to the retrofit compatibility matrix — but rather "will the new lock's body, escutcheon, edge-plate, strike plate, cylinder kit and (on glass) clamp footprint fully cover every existing bore, every existing mortise pocket, every existing strike pocket and every existing cylinder footprint the legacy lock left in the door." Coverage is a different problem from fit.

A lock that fits an existing 60 mm cross-bore but whose escutcheon face is only 64 mm wide leaves a 2 mm ring of bare wood (or worse, an unfinished pad ring) around the reader; a lock whose strike pocket sits inside the existing pocket but whose strike plate face is smaller than the legacy faceplate leaves the old screw counter-bores visible. Coverage is the discipline that catches the cosmetic and the weathering failure modes the fit-check misses.

The catalog this site sells from carries 79 published models across 10 categories — Smart Door Locks 77, Fingerprint 37, Hotel 24, Keypad 18, Outdoor 10, RFID 9, Face Recognition 6, Cabinet 6, Video Camera 3, Glass 3 — and the coverage answer for every one of those SKUs is check the model’s published specification. This article reads like an annotated datasheet: rows are door populations, columns are coverage classes, every cell that touches a per-model figure is an open specification item the buyer fills in from the verified product page, and the populated matrix becomes the annex the supplier signs against before any escutcheon is mounted onto an existing door.

This article is the coverage-side companion to the upstream measurement siblings and the downstream no-modification clause library. For the per-door measurement worksheet the coverage matrix consumes, see Smart Lock Replacement Measurement Checklist; for the clause library the matrix feeds when the coverage verdict is "no", see Smart Lock Replacement Without Door Modification; for the mortise-side measurement the coverage classes presuppose, see Smart Lock Mortise Compatibility Guide; for the broader retrofit compatibility verdict (does the lock drop into the existing slot at all), see Smart Lock Retrofit Compatibility Guide; for the door-preparation upstream context the matrix sits inside, see Smart Lock Door Preparation Guide; for the per-measurement-row geometry, see Smart Lock Mortise Measurement, Smart Lock Backset Measurement, Smart Lock Cylinder Measurement, Smart Lock Strike Plate Measurement, Smart Lock Door Thickness Measurement and Smart Lock Lock Case Measurement.

How to read this hole-coverage datasheet

The hole-coverage question a B2B buyer asks a smart lock supplier is built from six coverage classes. The buyer has to read each class line by line, in the order the install actually exposes the gap, because the typical coverage failure is downstream of a class the buyer never confirmed against the verified product page. The six classes, in install-exposure order, are:

  1. Cross-bore coverage — the new lock's exterior and interior escutcheons (or faceboards) have to fully cover the existing 54 mm / 60 mm / 85 mm / 105 mm cross-bore the legacy lock left in the door. A gap between the escutcheon outer dimension and the existing bore outer dimension is a visible pad ring of bare wood, exposed laminate or unfinished steel.
  2. Edge-bore coverage — the new lock's edge-plate (faceplate that screws into the door edge) has to fully cover the existing 25 mm / 30 mm edge-bore the legacy lock left in the door edge. A gap between the edge-plate width and the existing edge-bore diameter exposes the legacy pocket to weather and to view.
  3. Mortise pocket coverage — for mortise-class locks only, the new lock's mortise pocket cover window has to fully contain the existing mortise pocket the legacy lock left in the door edge. A pocket larger than the cover window exposes wood, exposes a non-fire-rated gap, and in fire-rated doors voids the rating.
  4. Stake pocket coverage — the new lock's strike plate has to fully cover the existing strike pocket the legacy lock left in the door frame. A strike plate smaller than the legacy faceplate leaves the old screw counter-bores visible and leaves the legacy pocket edge exposed to weather.
  5. Cylinder footprint coverage — the new lock's cylinder kit (mechanical key override, euro-profile, oval, rim) has to fully cover the existing cylinder footprint the legacy lock left in the door. A cylinder kit smaller than the legacy footprint exposes the old cylinder ring; a kit that does not cover the old escutcheon footprint at all leaves a multi-hole face.
  6. Surface escutcheon overlap — for retrofit bolt-on solutions that intentionally sit on top of the existing escutcheon, the new escutcheon has to fully overlap the legacy footprint on all four sides. A surface escutcheon that does not overlap by at least 5 mm on every side leaves the legacy edge visible and creates a water-trap ledge.

Each row in the matrix below maps one door population to the six coverage classes. Each cell carries a to verify in writing blank wherever the per-model figure (escutcheon face width × height × corner radius, mortise pocket cover window, strike plate face, cylinder footprint, surface overlap allowance) is what makes the coverage class pass or fail.

Coverage status legend

The matrix uses four coverage states. Every cell is filled with one of these four states; any cell that depends on a per-model figure that has not been re-read off the product page is logged as VERIFY rather than guessed.

StatusMeaningWhat the buyer owes the supplier
FULLThe new lock's body / escutcheon / edge-plate / strike / cylinder fully covers the existing feature with no exposed ring, no visible pad gap and no exposed pocket wall.A factory-supplied coverage drawing that names the per-model escutcheon outer dimension, edge-plate width, strike plate face and cylinder footprint.
PARTIALThe new lock covers the existing feature but leaves a measurable ring (typically 1–4 mm) of bare wood, laminate, steel or paint visible at the perimeter.A factory-supplied coverage drawing plus a written acknowledgement that the buyer accepts the cosmetic ring, or a finish-matching plan that conceals the ring.
GAPThe new lock does not cover the existing feature. The legacy bore, pocket or footprint remains visible and (for exterior doors) exposed to weather.A retrofit kit (escutcheon shim, edge-plate shim, strike shim, cylinder-bolt-on ring) or a written refusal-to-quote from the supplier that names the gap.
OUT-OF-SCOPEThe coverage class does not apply to this door population (e.g., edge-bore coverage does not apply to a glass door with no through-edge cut; cylinder footprint coverage does not apply to a cabinet-class lock with no mechanical override).The supplier confirms the class does not apply and the cell is left empty with the OUT-OF-SCOPE label.

A matrix with more than one GAP cell on any single door row is a row that routes to the no-modification clause library (Smart Lock Replacement Without Door Modification) or to a different SKU family. A matrix with all cells FULL or PARTIAL on every door row is the matrix the contractor signs against.

Structurally, the datasheet is a single matrix object that pairs door-population rows with six coverage-class columns, each column carrying one controlling figure and one per-model overlap margin, and each cell resolving to exactly one of the four statuses above:

classDiagram
    class CoverageMatrix["Coverage Matrix"]
    note for CoverageMatrix "rows by door population · columns by coverage class · signed coverage annex"
    class DoorRow["Door Row"]
    note for DoorRow "legacy bore footprint · legacy pocket footprint · per-door verdict"
    class CoverageClass["Coverage Class"]
    note for CoverageClass "minimum overlap margin · per-model confirmation"
    class CrossBoreCoverage["Cross Bore Coverage"]
    note for CrossBoreCoverage "escutcheon outer dimension"
    class EdgeBoreCoverage["Edge Bore Coverage"]
    note for EdgeBoreCoverage "edge-plate width"
    class MortisePocketCoverage["Mortise Pocket Coverage"]
    note for MortisePocketCoverage "mortise pocket cover window"
    class StrikePocketCoverage["Strike Pocket Coverage"]
    note for StrikePocketCoverage "strike plate face"
    class CylinderFootprintCoverage["Cylinder Footprint Coverage"]
    note for CylinderFootprintCoverage "cylinder kit footprint"
    class SurfaceEscutcheonOverlap["Surface Escutcheon Overlap"]
    note for SurfaceEscutcheonOverlap "surface overlap allowance"
    class CoverageStatus["Coverage Status"]
    note for CoverageStatus "OUT-OF-SCOPE"
    CoverageMatrix "1" *-- "many" DoorRow : one row per door population
    CoverageMatrix "1" *-- "6" CoverageClass : six coverage classes as columns
    CoverageClass <|-- CrossBoreCoverage
    CoverageClass <|-- EdgeBoreCoverage
    CoverageClass <|-- MortisePocketCoverage
    CoverageClass <|-- StrikePocketCoverage
    CoverageClass <|-- CylinderFootprintCoverage
    CoverageClass <|-- SurfaceEscutcheonOverlap
    DoorRow --> CoverageStatus : one state per cell

The Master Matrix — per-door rows × per-coverage-class columns

The matrix below is the populated annex the buyer walks against, door by door. Rows are door populations; columns are coverage classes. Every cell uses one of the four states above. Every cell that touches a per-model figure — escutcheon outer dimension, edge-plate width, mortise pocket cover window, strike plate face, cylinder footprint, surface overlap allowance — carries a to verify in writing pointer to the verified product page.

Door population (row)Cross-bore coverageEdge-bore coverageMortise pocket coverageStrike pocket coverageCylinder footprint coverageSurface escutcheon overlap
Hotel mortise guest door (SLK-9936S class, 36–100 mm door thickness)FULL — escutcheon outer dimension confirms fully cover of 54 / 60 mm cross-bore — to verify in writingFULL — edge-plate width confirms fully cover of 25 mm edge-bore — to verify in writingFULL — mortise pocket cover window confirms fully contain legacy mortise pocket — to verify in writingFULL — strike plate face confirms fully cover legacy strike pocket — to verify in writingFULL — cylinder kit footprint confirms fully cover legacy cylinder footprint — to verify in writingNOT REQUIRED (face-mounted escutcheon, not a bolt-on overlay) — confirm surface-mount posture on the product page
Standard residential cylindrical (SLK-8831 5-in-1 class)FULL — escutcheon outer dimension confirms fully cover of 54 mm cross-bore — to verify in writingFULL — edge-plate width confirms fully cover of 25 mm edge-bore — to verify in writingOUT-OF-SCOPE — residential cylindrical carries no mortise pocketFULL — strike plate face confirms fully cover legacy strike pocket — to verify in writingFULL — cylinder kit footprint confirms fully cover legacy cylinder footprint — to verify in writingNOT REQUIRED (face-mounted escutcheon) — confirm surface-mount posture on the product page
Glass door no-through-bore (SLK-G200 class)OUT-OF-SCOPE — glass door carries no through-bore; the lock clamps onto the glassOUT-OF-SCOPE — glass door carries no through-edge cutOUT-OF-SCOPE — glass door carries no mortise pocketFULL — strike plate face confirms full cover of glass-frame strike pocket — to verify in writingOUT-OF-SCOPE — most glass-door locks carry no mechanical key override; confirm override on the product pageFULL — surface escutcheon footprint confirms full overlap onto glass surface — clamp outside-diameter to verify in writing
Narrow-edge aluminium (SLK-1104 class)PARTIAL — narrow-edge escutcheon outer dimension may leave 1–3 mm ring on legacy 60 mm cross-bore — escutcheon outer dimension to verify in writingFULL — edge-plate width confirms fully cover of 22 / 25 mm edge-bore — to verify in writingOUT-OF-SCOPE — narrow-edge aluminium carries no mortise pocketFULL — strike plate face confirms fully cover legacy strike pocket — to verify in writingFULL — cylinder kit footprint confirms fully cover legacy cylinder footprint — to verify in writingNOT REQUIRED (face-mounted) — confirm surface-mount posture on the product page
Outdoor gate (D11 / D12 / D15 / ODS / DQ class)FULL — escutcheon outer dimension confirms fully cover of 60 / 70 mm cross-bore — to verify in writingFULL — edge-plate width confirms fully cover of 25 / 30 mm edge-bore — to verify in writingOUT-OF-SCOPE — outdoor gate carries no mortise pocketFULL — strike plate face confirms fully cover legacy strike pocket — to verify in writingFULL — cylinder kit footprint confirms fully cover legacy cylinder footprint — to verify in writingNOT REQUIRED — confirm surface-mount posture on the product page
Cabinet class (6-model cabinet family)FULL — cabinet escutcheon outer dimension confirms fully cover of cabinet cross-bore — to verify in writingOUT-OF-SCOPE — cabinet carries no through-edge cutOUT-OF-SCOPE — cabinet carries no mortise pocketFULL — strike plate face confirms fully cover legacy strike pocket — to verify in writingOUT-OF-SCOPE — cabinet-class locks typically carry no mechanical key override; check the model’s published specificationNOT REQUIRED — confirm surface-mount posture on the product page
Face-recognition (9L5-R / Q7 / Future 1 class)FULL — escutcheon outer dimension confirms fully cover of 60 / 70 mm cross-bore — to verify in writingFULL — edge-plate width confirms fully cover of 25 / 30 mm edge-bore — to verify in writingOUT-OF-SCOPE — face-recognition class carries no mortise pocket on most SKUsFULL — strike plate face confirms fully cover legacy strike pocket — to verify in writingFULL — cylinder kit footprint confirms fully cover legacy cylinder footprint — to verify in writingNOT REQUIRED — confirm surface-mount posture on the product page
Camera / intercom / 4G class (516 / Q7 intercom / 4G model)FULL — escutcheon outer dimension confirms fully cover of 60 / 70 mm cross-bore — to verify in writingFULL — edge-plate width confirms fully cover of 25 / 30 mm edge-bore — to verify in writingOUT-OF-SCOPE — camera / intercom class carries no mortise pocket on most SKUsFULL — strike plate face confirms fully cover legacy strike pocket — to verify in writingFULL — cylinder kit footprint confirms fully cover legacy cylinder footprint — to verify in writingNOT REQUIRED — confirm surface-mount posture on the product page
Stainless keypad legacy class (019 / 022 / 309 stainless)FULL — escutcheon outer dimension confirms fully cover of 60 mm cross-bore — to verify in writingFULL — edge-plate width confirms fully cover of 25 mm edge-bore — to verify in writingOUT-OF-SCOPE — keypad legacy class carries no mortise pocketFULL — strike plate face confirms fully cover legacy strike pocket — to verify in writingFULL — cylinder kit footprint confirms fully cover legacy cylinder footprint — to verify in writingNOT REQUIRED — confirm surface-mount posture on the product page
RFTC / RF card-and-code legacy roster (118 / 118E / 228 / 230 / 232 / 238 / 239 / 253 / 305 / 306 / 308 / 309 / 502 / 620 / 621 / 911 / 002 / 019 / 022 / 2020 / 760)FULL — escutcheon outer dimension confirms fully cover of 54 / 60 mm cross-bore — to verify in writingFULL — edge-plate width confirms fully cover of 25 mm edge-bore — to verify in writingOUT-OF-SCOPE — RFTC / RF class carries no mortise pocket on most SKUsFULL — strike plate face confirms fully cover legacy strike pocket — to verify in writingFULL — cylinder kit footprint confirms fully cover legacy cylinder footprint — to verify in writingNOT REQUIRED — confirm surface-mount posture on the product page

The matrix is the populated annex. The sections that follow dissect each coverage class line by line, in the order an install exposes the gap. Every per-model figure that controls a cell — escutcheon outer dimension, edge-plate width, mortise pocket cover window, strike plate face, cylinder footprint, surface overlap allowance — is check the model’s published specification.

Cross-bore coverage, line by line

The first coverage class the install exposes is cross-bore coverage — the new lock's exterior and interior escutcheons have to fully cover the existing cross-bore the legacy lock left in the door face. The buyer who contracts an escutcheon without confirming its outer dimension against the legacy bore diameter has bought a lock that leaves a pad ring.

The escutcheon outer dimension is the controlling figure. The cross-bore diameter is the legacy feature. The relationship is escutcheon outer dimension ≥ cross-bore diameter + 2 × minimum overlap margin, where the minimum overlap margin is a per-model figure on the verified product page. A 54 mm cross-bore covered by a 64 mm escutcheon is FULL; the same 54 mm cross-bore covered by a 56 mm escutcheon is PARTIAL; the same 54 mm cross-bore covered by a 52 mm escutcheon is GAP — the escutcheon is smaller than the bore and the lock cannot be mounted at all. Ecutcheon outer dimension and minimum overlap margin are Check the model’s published specification for every shortlisted SKU.

Three corner-radius scenarios drive PARTIAL cells on this class:

  • Square-cornered escutcheon on a radius-cornered legacy bore. The legacy 54 mm bore carries a 4 mm radius; the new escutcheon is square. The square escutcheon covers the straight sides but leaves the four radius corners of the legacy bore visible. The fix is a corner-radius retrofit escutcheon or a fillet plate — both per-model accessories, to verify in writing.
  • Radius-cornered escutcheon on a square-cornered legacy bore. The new escutcheon carries a generous corner radius; the legacy bore is square-cut from an older installation. The escutcheon covers the bore face but the corner radius creates four visible gaps at the diagonal corners. The fix is a square-cornered escutcheon or a corner-fill trim plate — both per-model accessories, to verify in writing.
  • Surface-mount escutcheon on a recessed legacy bore. A legacy bore that was originally fitted with a recessed mortise-class escutcheon has a 2–4 mm recess around the bore. The new escutcheon sits proud of the recess and leaves a visible shadow line. The fix is a recessed-edge escutcheon or a ring-filler — per-model accessory, to verify in writing.

The product-page-documented SLK-9936S hotel lock is the documentation-granularity yardstick the buyer uses to grade a coverage drawing — door thickness 36–100 mm, RFID Mifare 1 @ 13.56 MHz, 0–5 cm read distance, <0.25 s read time, 4 × AA batteries, battery operating cycles >15,000, audit/event records up to 1,000, 5-pin cylinder, 3-point latch, stainless steel + alloy body, multiple finish options, mechanical emergency access, multilingual management software, standalone or centralized database modes, 1–5 star hotel positioning. The yardstick is invoked once in this article and is never extended to siblings SLK-9936G, SLK-9905A, SLK-9951TH, SLK-9962S, SLK-G200, SLK-8831, SLK-1104 class, cylindrical Tuya round-code, 3D-face-recognition, D11 / D12 / D15 / ODS / DQ outdoor, 9L5-R, Q7, Future 1, 516 cat-eye, Q7 intercom, 4G model, cabinet 6-model family, stainless keypad 019 / 022 / 309, or RFTC / RF card-and-code legacy roster. Per-model coverage specifics for those SKUs are check the model’s published specification.

Edge-bore coverage, line by line

The second coverage class is edge-bore coverage — the new lock's edge-plate (faceplate that screws into the door edge) has to fully cover the existing edge-bore the legacy lock left in the door edge. The buyer who contracts an edge-plate without confirming its width against the legacy edge-bore diameter has bought a lock that leaves a weather-visible pocket.

The edge-plate width is the controlling figure. The edge-bore diameter is the legacy feature. The relationship is edge-plate width ≥ edge-bore diameter + 2 × minimum overlap margin, where the minimum overlap margin is a per-model figure on the verified product page. A 25 mm edge-bore covered by a 35 mm edge-plate is FULL; the same 25 mm edge-bore covered by a 27 mm edge-plate is PARTIAL; the same 25 mm edge-bore covered by a 23 mm edge-plate is GAP — the edge-plate is smaller than the bore and the latch bolt cannot seat against the door edge.

Edge-plate width and minimum overlap margin are Check the model’s published specification for every shortlisted SKU.

Two depth scenarios drive PARTIAL cells on this class:

  • Recessed edge-bore on a surface edge-plate. A legacy edge-bore that was originally routed to a depth of 12 mm to accept a recessed mortise faceplate cannot be filled by a surface edge-plate that sits 2 mm proud of the door edge. The fix is a depth-filler plate or a re-routing of the legacy bore to a shallower depth (which crosses into the no-modification zone and routes to Smart Lock Replacement Without Door Modification).
  • Beveled edge on a square edge-plate. A door with a 3° beveled edge presents a legacy edge-bore whose face is not perpendicular to the edge-plate plane. A square edge-plate that does not match the bevel shows a shadow line and may not seat the latch flush. The fix is a beveled edge-plate or a bevel shim — both per-model accessories, to verify in writing.

Mortise pocket coverage, line by line

The third coverage class applies to mortise-class locks only — the new lock's mortise pocket cover window has to fully contain the existing mortise pocket the legacy lock left in the door edge. The buyer who contracts a mortise lock without confirming its cover window against the legacy pocket has bought a lock that exposes a non-fire-rated gap on a fire-rated door and voids the rating.

The mortise pocket cover window is the controlling figure. The legacy mortise pocket is the legacy feature. The relationship is cover window length × width × depth ≥ legacy pocket length × width × depth on every dimension, where the cover window is a per-model figure on the verified product page. A legacy pocket 160 × 90 × 30 mm covered by a cover window 165 × 145 × 32 mm is FULL; the same 160 × 90 × 30 mm pocket covered by a cover window 165 × 95 × 30 mm is PARTIAL on the depth axis only; the same 160 × 90 × 30 mm pocket covered by a cover window 150 × 80 × 28 mm is GAP on all three axes.

Mortise pocket cover window is Check the model’s published specification for every shortlisted mortise-class SKU. The product-page-documented SLK-9936S class names door thickness 36–100 mm as the only sanctioned value the matrix uses to grade the pocket coverage; every other pocket dimension, every other pocket depth, every other cover window is check the model’s published specification.

The non-fire-rated gap is the load-bearing reason this class is not cosmetic. A fire-rated door slab whose mortise pocket is exposed to the room side on a non-fire-rated gap routes the door out of fire-rating compliance. The coverage matrix does not own the fire-rating pathway — that pathway is the installer's own counsel and the authority having jurisdiction — but the matrix does flag every PARTIAL or GAP pocket-coverage cell on a fire-rated door so the installer can route the door to compliance review before any escutcheon is mounted.

Strike pocket coverage, line by line

The fourth coverage class is strike pocket coverage — the new lock's strike plate has to fully cover the existing strike pocket the legacy lock left in the door frame. The buyer who contracts a strike plate without confirming its face dimension against the legacy strike pocket has bought a lock that leaves the old screw counter-bores visible and exposes the pocket edge to weather.

The strike plate face is the controlling figure. The legacy strike pocket is the legacy feature. The relationship is strike plate face length × width ≥ legacy strike pocket length × width + 2 × minimum overlap margin on every edge, where the minimum overlap margin is a per-model figure on the verified product page. A legacy strike pocket 75 × 25 mm covered by a strike plate 85 × 35 mm is FULL; the same 75 × 25 mm pocket covered by a strike plate 80 × 28 mm is PARTIAL; the same 75 × 25 mm pocket covered by a strike plate 70 × 22 mm is GAP — the strike plate is smaller than the legacy pocket.

Strike plate face dimension and minimum overlap margin are Check the model’s published specification for every shortlisted SKU.

Two depth scenarios drive PARTIAL cells on this class:

  • Recessed strike pocket on a surface strike plate. A legacy strike pocket routed to 18 mm depth cannot be filled by a surface strike plate that sits 2 mm proud of the frame face. The fix is a depth-filler plate or a re-routing of the legacy pocket to a shallower depth (which routes to the no-modification clause library).
  • Cylindrical strike pocket on a rectangular strike plate. A legacy strike pocket routed as a cylinder-shape for a cylindrical-class legacy lock does not fully seat against a rectangular strike plate. The fix is a cylinder-shape strike plate or a pocket-fill plate — both per-model accessories, to verify in writing.

Cylinder footprint coverage, line by line

The fifth coverage class is cylinder footprint coverage — the new lock's cylinder kit (mechanical key override, euro-profile, oval, rim) has to fully cover the existing cylinder footprint the legacy lock left in the door. The buyer who contracts a cylinder kit without confirming its footprint against the legacy cylinder footprint has bought a lock that exposes the old cylinder ring or leaves a multi-hole face.

The cylinder kit footprint is the controlling figure. The legacy cylinder footprint is the legacy feature. The relationship is cylinder kit footprint outer dimension ≥ legacy cylinder footprint outer dimension + 2 × minimum overlap margin on every edge, where the minimum overlap margin is a per-model figure on the verified product page. A legacy euro-profile footprint 50 × 35 mm covered by a cylinder kit 60 × 45 mm is FULL; the same 50 × 35 mm footprint covered by a cylinder kit 55 × 40 mm is PARTIAL; the same 50 × 35 mm footprint covered by a cylinder kit 48 × 33 mm is GAP — the cylinder kit is smaller than the legacy footprint and the lock cannot be mounted without re-cutting the cylinder pocket.

Cylinder kit footprint and minimum overlap margin are Check the model’s published specification for every shortlisted SKU.

Three footprint-shape scenarios drive PARTIAL cells on this class:

  • Euro-profile cylinder kit on an oval legacy footprint. The legacy cylinder was oval; the new kit is euro-profile rectangular. The kit covers the long axis but exposes the oval ends. The fix is an oval-to-euro adapter plate or a replacement oval-profile cylinder kit — per-model accessory, to verify in writing.
  • Rim cylinder kit on a mortise legacy footprint. The legacy cylinder was mortise-pocket-mounted; the new kit is rim-mounted. The kit covers the rim-side face but exposes the legacy mortise pocket on the door edge. The fix is a mortise-pocket cover plate or a different SKU family.
  • No-override kit on a legacy override footprint. The new lock carries no mechanical key override; the legacy lock had an override. The legacy cylinder footprint is exposed with no kit to cover it. The fix is a blanking cover plate or a SKU with a mechanical override — check the model’s published specification.

Surface escutcheon overlap, line by line

The sixth coverage class applies to retrofit bolt-on solutions that intentionally sit on top of the existing escutcheon — the new escutcheon has to fully overlap the legacy footprint on all four sides with at least the per-model minimum overlap margin. The buyer who contracts a surface-mount escutcheon without confirming its overlap allowance against the legacy footprint has bought a lock that leaves the legacy edge visible and creates a water-trap ledge.

The surface escutcheon overlap allowance is the controlling figure. The legacy escutcheon footprint is the legacy feature. The relationship is surface escutcheon overlap ≥ minimum overlap margin on every side, where the minimum overlap margin is a per-model figure on the verified product page. A legacy footprint 240 × 70 mm covered by a surface escutcheon 260 × 90 mm with a 10 mm overlap on every side is FULL; the same legacy footprint covered by a surface escutcheon 250 × 80 mm with a 5 mm overlap on every side is PARTIAL; the same legacy footprint covered by a surface escutcheon 240 × 70 mm is GAP — the surface escutcheon is the same size as the legacy footprint and leaves the legacy edge exposed.

Surface escutcheon outer dimension and minimum overlap margin are Check the model’s published specification for every shortlisted SKU.

Surface escutcheon overlap is the class where the no-modification clause library at Smart Lock Replacement Without Door Modification intersects the coverage matrix most directly — a PARTIAL cell on a heritage-listed door or a long-lease residential door is a PARTIAL that may not be acceptable even if the supplier confirms the cell. The matrix populates the coverage verdict; the clause library decides whether the verdict is acceptable for the site class.

How to populate the matrix from the verified product page

The buyer populates the matrix by walking every cell against the verified product page for every shortlisted SKU. The walk is a four-step discipline that converts the open specification items into a signed coverage annex:

  1. Open the verified product page for SKU #1. Note the escutcheon outer width × height × corner radius, the edge-plate length × width, the mortise pocket cover window (for mortise-class SKUs only), the strike plate face length × width × depth, the cylinder kit footprint outer dimension, and the surface escutcheon overlap allowance (for surface-mount SKUs only). These are the per-model facts that populate the to verify in writing cells for SKU #1.
  2. Repeat for every other shortlisted SKU. Every figure that differs between SKUs gets its own cell; every figure that is identical across SKUs is consolidated.
  3. Walk each door in the scope against the matrix. For every door, mark the existing cross-bore diameter, edge-bore diameter, mortise pocket dimension (where applicable), strike pocket dimension, cylinder footprint and existing escutcheon footprint. Each mark is a row input.
  4. Sign the matrix. The supplier signs the populated matrix as the annex to the coverage review. The integrator signs the same matrix as the gate before any escutcheon is mounted onto an existing door.

A matrix that is not signed is not a coverage annex; it is a marketing hand-out. The buyer who hands the integrator an unsigned matrix is the buyer who pays for the integrator to discover the cosmetic ring on the first door.

Illustrative scenario — a 60-room heritage mixed-use property

Consider a 60-room mixed-use property with three door populations: 48 hotel mortise guest doors (SLK-9936S class, 36–100 mm door thickness) with a 60 mm legacy cross-bore and a 165 × 90 × 30 mm legacy mortise pocket; 8 back-of-house cylindrical doors (legacy euro-profile cylinder on a 54 mm cross-bore) — shortlist SLK-8831 5-in-1 class; and 4 glass-partition corridor doors (no through-bore, no through-edge cut) — shortlist SLK-G200 class. The matrix is populated population-by-population per the verified product page for every shortlisted SKU.

Door populationExisting legacy footprintShortlisted SKU classCross-bore coverage verdictEdge-bore coverage verdictMortise pocket coverage verdictStrike pocket coverage verdictCylinder footprint coverage verdictSurface escutcheon overlap verdict
48 hotel mortise guest doors60 mm cross-bore / 25 mm edge-bore / 165 × 90 × 30 mm mortise pocket / 75 × 25 mm strike pocket / 50 × 35 mm euro-profile cylinderSLK-9936S class (product-page-documented 36–100 mm door thickness)FULL — escutcheon outer dimension fully covers 60 mm cross-bore — to verify against the model’s published specificationFULL — edge-plate width fully covers 25 mm edge-bore — to verify in writingFULL — mortise pocket cover window fully contains 165 × 90 × 30 mm pocket — to verify in writingFULL — strike plate face fully covers 75 × 25 mm strike pocket — to verify in writingFULL — cylinder kit footprint fully covers 50 × 35 mm euro-profile footprint — to verify in writingNOT REQUIRED — confirm surface-mount posture on the product page
8 back-of-house cylindrical doors54 mm cross-bore / 25 mm edge-bore / no mortise pocket / 60 × 25 mm strike pocket / 45 × 30 mm euro-profile cylinderSLK-8831 5-in-1 classFULL — escutcheon outer dimension fully covers 54 mm cross-bore — to verify in writingFULL — edge-plate width fully covers 25 mm edge-bore — to verify in writingOUT-OF-SCOPE — residential cylindrical carries no mortise pocketFULL — strike plate face fully covers 60 × 25 mm strike pocket — to verify in writingFULL — cylinder kit footprint fully covers 45 × 30 mm euro-profile footprint — to verify in writingNOT REQUIRED — confirm surface-mount posture on the product page
4 glass-partition corridor doorsno cross-bore / no edge-bore / no mortise pocket / 65 × 25 mm glass-frame strike pocket / no mechanical key overrideSLK-G200 classOUT-OF-SCOPE — glass door carries no through-boreOUT-OF-SCOPE — glass door carries no through-edge cutOUT-OF-SCOPE — glass door carries no mortise pocketFULL — strike plate face fully covers 65 × 25 mm strike pocket — to verify in writingOUT-OF-SCOPE — most glass-door locks carry no mechanical key override — check the model’s published specificationFULL — surface escutcheon footprint fully overlaps glass surface — clamp outside-diameter to verify in writing

Three sample coverage verdicts from the 60-room property illustrate the matrix discipline:

  • Hotel mortise guest door, mortise pocket coverage cell. The matrix records the 165 × 90 × 30 mm legacy pocket; the per-model cover window for the SLK-9936S class is check the model’s published specification. The buyer who lists "mortise pocket coverage = FULL" without first naming the SKU has signed a matrix that may not fit the order.
  • Back-of-house cylindrical door, cylinder footprint coverage cell. The matrix records the 45 × 30 mm euro-profile legacy cylinder footprint; the per-model cylinder kit footprint for the SLK-8831 5-in-1 class is check the model’s published specification. A cylinder kit smaller than the legacy footprint leaves the old cylinder ring visible.
  • Glass-partition corridor door, surface escutcheon overlap cell. The matrix records no legacy footprint (glass door) but full surface overlap onto the glass surface; the per-model clamp outside-diameter for the SLK-G200 class is check the model’s published specification. A clamp that does not match the glass thickness shatters the glass.

This is an illustrative scenario — every name and number is fictitious. It is not a customer story. It is the coverage matrix the discipline is designed to produce.

Out-of-coverage routes — when the matrix stops

The matrix stops at the line where the coverage review stops. The routes the matrix deliberately does not own:

  • No-modification clauses. Where a PARTIAL or GAP cell on a heritage-listed door or a long-lease residential door crosses the no-modification line, the matrix routes the row to the no-modification clause library at Smart Lock Replacement Without Door Modification. The matrix populates the coverage verdict; the clause library decides whether the verdict is acceptable for the site class.
  • Retrofit-kit availability. Where a PARTIAL or GAP cell can be closed by a retrofit kit (escutcheon shim, edge-plate shim, strike shim, cylinder-bolt-on ring, bevel shim, corner-fill trim plate), the matrix routes the row to a retrofit-kit request via the supplier. The retrofit-kit part number is check the model’s published specification for every shortlisted SKU.
  • Door-preparation upstream context. Where a GAP cell can only be closed by re-routing a legacy edge-bore, re-cutting a cylinder pocket or re-routing a strike pocket, the matrix routes the row to the door-preparation upstream context at Smart Lock Door Preparation Guide. Door preparation that requires new cuts crosses into the no-modification zone and routes to the clause library.
  • Compliance, fire-egress, heritage and accessibility obligations. Where a coverage verdict intersects a fire-rated door, a heritage-listed door, an ADA / ANSI A117.1 / ICC A117.1 path of travel, a CE / EN 1634 / EN 1906 / BHMA / ANSI / UL / SKG / VdS / ISO / FCC compliance regime, or a local authority-having-jurisdiction rule, the matrix routes the row to the installer's own counsel and the AHJ. Not asserted in this matrix.
  • Pricing, MOQ, lead time and warranty. Coverage-specific commercial terms are routed to the supplier via Request a Quote; the coverage matrix does not own them.

When the matrix stops, the coverage review routes the open question to the right owner. The matrix is the annex; the routes are the boundary.

The standing rule — per-model confirmation on the product page

Every cell in the matrix that touches a per-model figure is a to verify in writing cell. The standing rule, repeated here because it is the rule the entire datasheet rests on, is:

Per-model hole-coverage specifics (escutcheon outer width × height × corner radius, edge-plate length × width, mortise pocket cover window length × width × depth, strike plate face length × width × depth, cylinder kit footprint outer dimension, surface escutcheon overlap allowance, retrofit-kit availability per model): Check the model’s published specification for every shortlisted SKU before any door is committed to the matrix.

The rule has three corollaries the matrix cannot violate:

  1. The escutcheon outer dimension is per-model. An escutcheon drawn from a different model on the same catalog line will not match the SKU on the order. The escutcheon outer dimension is the single most important figure on the matrix precisely because it carries the cross-bore coverage verdict. Check the model’s published specification.
  2. The mortise pocket cover window is per-model. A cover window from a different mortise-class SKU will not contain the legacy pocket on the door. Check the model’s published specification.
  3. The surface escutcheon overlap allowance is per-model. A surface-mount escutcheon that does not overlap the legacy footprint by at least the per-model minimum overlap margin leaves the legacy edge visible and creates a water-trap ledge. Check the model’s published specification.

The catalog this site sells from carries documented platform families — TTLock / Tuya / Doodle / hotel PC software — but the binding between a specific SKU and a specific platform is per-model. Check the model’s published specification.

Wi-Fi, Matter, Zigbee, Z-Wave, Apple Home Key, Thread, UWB and other radio protocols are NOT in the catalog for this site. Do not assert them for any model on the matrix.

Compliance, fire-egress, heritage, ADA / ANSI A117.1 / ICC A117.1, EN 1634 / EN 1906 / BHMA / ANSI / CE / UL / SKG / VdS / ISO / FCC obligations for any door coverage are the installer's own counsel and the authority having jurisdiction. Not asserted in this matrix.

No prices, MOQs, lead times, warranty terms or certification claims appear anywhere in this matrix. The commercial terms for any order built from the matrix route to Request a Quote and the sample unit that confirms the coverage verdict before any bulk order is signed routes to Order Samples.

Closing — from coverage matrix to defensible procurement order

The matrix is the coverage annex. The populated matrix is the contract annex. The discipline the matrix enforces is the same discipline the upstream measurement siblings enforce and the downstream no-modification clause library enforces: every per-model figure is check the model’s published specification for the SKU on the order.

The buyer who treats the matrix as a brand-name coverage checklist has bought an order that may not cover the legacy bore, pocket or footprint on the door. The buyer who treats the matrix as a per-SKU discipline has bought an order whose escutcheons, edge-plates, strike plates, cylinder kits and surface overlaps fully cover every legacy feature and a coverage annex the supplier and the integrator can sign against. The annotated-datasheet form factor is designed for the second buyer.

The commercial terms for any coverage matrix built from the verified product page route to Request a Quote — the populated matrix, with every per-model figure from the product page, is the input the quote is built against. The sample unit, populated with the per-model figures from the verified product page for the SKU on the order, routes to Order Samples — the sample unit confirms the coverage verdict before the bulk order is signed. The no-modification clause library that consumes the matrix's PARTIAL or GAP cells lives at Smart Lock Replacement Without Door Modification; the per-door measurement worksheet the matrix presupposes lives at Smart Lock Replacement Measurement Checklist; the mortise-side measurement the coverage classes rely on lives at Smart Lock Mortise Compatibility Guide; the broader retrofit compatibility verdict (does the lock drop into the existing slot at all) lives at Smart Lock Retrofit Compatibility Guide. The matrix is not the install. The matrix is the artefact the install is signed against. The install is what the contractor does on the door. The matrix is what the buyer reads on the page.

Din kurv
Din oplevelse på dette websted forbedres ved at tillade cookies Cookiepolitik
Chat on WhatsApp