Miss any one and the lock arrives, the crew discovers it at the door, and the project pays for the mistake in the worst currency there is: schedule.

게시일: 12월 03, 2025

SLK-8831 Door Compatibility Guide

SLK-8831 Door Compatibility Guide

Direct answer: door compatibility for a 5-in-1 digital door lock is a six-condition test, not a one-number test. A door accepts the SLK-8831 only when all six of these are measured and reconciled at once: door thickness at the lock edge, cross-bore and edge-bore diameter, backset, lock-edge (stile) width, handing — which way the door hangs and swings — and the condition of the edge, frame and leaf construction. Miss any one and the lock arrives, the crew discovers it at the door, and the project pays for the mistake in the worst currency there is: schedule.

The second answer matters just as much, and it is the one this guide is built around. The SLK-8831's documented first-party fact in our record is its credential identity — fingerprint, password, card, mechanical key and app. Its dimensional envelope is not in our record. That makes every fit line for this model a blank cell you fill from the live product page or from a dated written supplier reply. This guide publishes no thickness band, no bore diameter and no backset for the SLK-8831, deliberately. What it publishes instead is the survey that produces those numbers, the measurement discipline behind each of the six, and the dossier format that turns your measurements and the supplier's commitments into one quotable document.

GEO ANSWER — Will the SLK-8831 fit my door?Measure six things per door: thickness at the lock edge (min and max, three heights), existing cross-bore and edge-bore diameters, backset, lock-edge stile width, handing (left/right, forward/reverse), and edge/frame condition. Capture the SLK-8831's own envelope for each of those six from its product page or a written supplier reply. A door passes only when all six measured values sit inside all six captured commitments; anything else is a documented prep decision or a different model.

The Six-Condition Fit Model

Most compatibility conversations in this product class start and end at thickness. That habit comes from hotel lock retrofits, where the door population is fairly uniform and the cylinder is short, and it travels badly to residential and apartment digital locks, where the exterior housing, the reader stack, the interior assembly and the through-fixings all occupy more of the door.

ConditionWhat it decides on the doorHow you read it off the doorWhere a wrong value first surfaces
Door thickness at lock edgeWhether the two halves of the lock clamp the leaf with correct fastener length and no strainCaliper on the closed door's lock edge at three heights; record extremesFitting stage — rock, rattle, protruding bolt ends
Cross-bore and edge-bore diameterWhether the body/launcher fits the hole(s) already in the door, or how much new cutting is neededRule down the bore diameter; compare to templateCutting stage — gap around body, or hole too small
BacksetWhere the mechanism sits relative to the edge, and whether the latch reaches the strikeEdge to bore centreline, measured through the boreCommissioning — latch bind, bolt stops short
Lock-edge stile widthWhether there is enough solid material to carry the bore plus fixingsOn the lock-edge face, edge to first joint/mould line at hardware heightCutting stage — breakout into the panel, weak fixings
Handing and swingWhich face carries the exterior unit, which way the lever/latch points, where the strike goesHinge-face observation, then classificationAfter install — handle orientation wrong, latch bevel fighting the strike
Edge, frame and leaf conditionWhether the geometry the measurements assume actually existsVisual + physical check against the list in this guide's fifth sectionWeeks later — misalignment blamed on electronics

The rule that follows from the table: no dimension is qualified alone. A door can be a perfect 45 mm thickness, correctly bored, correctly handed, and have a 48 mm rail at the lock edge that cannot hold a 60 mm bore without breaking into the panel. Compatibility is the intersection of six sets, and the register is what proves the intersection is non-empty.

Thickness: the Clamping Dimension

Thickness is the one dimension where sibling guides in this catalog can show you a completed cell. The SLK-9936S hotel lock publishes a door thickness of 36–100 mm with a 5-pin cylinder and a 3-point latch; the SLK-9905A hidden-reader model publishes approximately 38–100 mm. Those lines are useful to you as format examples — a band expressed as min–max, tied to one named model — and they are dangerous as values borrowed for anything else. An envelope belongs to a model. Never port one.

Why a five-method residential lock is thickness-sensitive in its own way: the SLK-8831 stacks more hardware across the leaf than a single-function keypad. Whatever the exterior housing, interior assembly, reader module and mechanical-key path occupy, they are all clamped between two faces by fasteners whose usable length is set by the door. Concretely, four consequences run off thickness:

  • Fastener reach. Long bolts in a thin door protrude inside and foul the interior assembly; short bolts in a thick door never clamp, and the whole unit rocks. Rocking is what turns a healthy latch into an intermittent complaint three weeks after handover.
  • Cylinder and key path. One of the five declared methods is a mechanical key. If the key route uses a through-door cylinder, its length is a thickness-dependent dimension, together with how far it may sit proud on the inside. That is a REQUEST line, not a guess — and it is the same line the mechanical key override guide needs before anyone talks about emergency access.
  • Spindle or tailpiece length. Handle-driven locks transmit torque through a bar whose length must match the measured thickness, not a nominal one. Cutting by nominal is how a lever ends up with end-play.
  • Bracketing pressure on the leaf. Thin or hollow leaves need documented spacer/backing treatment before anything is torqued. Compressing a hollow core around a fixing distorts the case and jams the mechanism quietly.

The measurement protocol that makes thickness a fact rather than an opinion: door closed; instrument on the lock edge, in the region where the hardware will actually sit; three heights (roughly 300 mm from the bottom, mid-height, 300 mm from the top); record minimum and maximum separately, never a mean; note the tool; re-measure anything near a boundary with a second person and a second instrument on a different day. Paint and lacquer count as door — you are buying for the leaf that exists. The full census methodology behind this — populations, sampling rules, failure modes to refuse — is worked through in the SLK-9936S door thickness compatibility guide, and it transfers as method, not as numbers.

Bores and Cut-Outs: the Holes That Carry the Mechanism

Thickness is a dimension of the door. Bore diameters are a dimension of the conversation between door and lock, which is why they break more retrofit projects than anything else in this guide.

Three vocabularies collide in this product class, and a buyer who mixes them writes an unusable RFQ:

  • Cross bore — the large hole drilled through both faces of the door at the hardware centreline.
  • Edge bore — the hole drilled into the door edge, perpendicular to the cross bore, through which the latch or deadbolt emerges.
  • Auxiliary bore — a second small edge-to-face hole offset from the latch, historically for a cylinder or a deadbolt, common on doors converted from lever-set to knob-and-deadbolt.
  • Cut-out / mortise pocket — the recess, either at the edge (case pocket) or the face (furniture hole), that houses the body rather than a round bore.

Existing doors come to you with a legacy of one of these vocabularies. Read it before you order.

Prep tradition you will actually meetWhat the door already hasReference values commonly specified in door-trade practiceWhat to confirm against the model's own bore line
ANSI mortise (commercial and older apartment doors)Large face cross bore plus edge bore, sometimes an auxiliary cylinder boreCross bore 2-3/8 in (~60 mm); edge/auxiliary bore 1 in (~25 mm)Whether the lock's case pocket and bore demand a mortise conversion — and what template the supplier supplies
ANSI cylindrical / deadboltFace cross bore at both lever and deadbolt positions2-1/8 in (~54 mm) cross bore for cylindrical sets; 1-1/2 in (~38 mm) for deadbolt bodies; 1 in (~25 mm) edge boreWhether the exterior unit covers the old 54 mm hole or leaves it exposed
Euro-profile / metric mortise (mainland Europe, much of Asia, Middle East)Edge case pocket, a cylinder hole through the face, two follower (spindle) holes17 mm Euro-profile cylinder bore; PZ centre distance commonly 72 mm or 78 mm; furniture hole around 68 mm; backset commonly 60 mm or 72 mmCylinder length and the PZ dimension the lock assumes, in writing
Bare or newly ordered doorsNothing—Whether you order the door pre-drilled to the supplier's template, or field-cut with it
Altered / previously-repaired doorsOld holes, plugs, fillers, scars—Whether legacy holes fall inside the new cut-out, and who signs the fill/plate decision

Cells marked — have no documented value in this article’s sources; obtain the figure from the supplier’s written specification.

Every figure in the middle column is door-trade context, not SLK-8831 data. They exist so you can name what you found when you write to the factory: "our doors are 2-3/8 in cross-bored mortise preps, 72 mm backset, Euro-profile cylinder hole at 72 mm PZ" is a sentence a supplier can answer. "Our doors are standard" is a sentence nobody can.

The compatibility question bores reduce to is a single one: does the lock's required hole geometry coincide with the door's existing geometry, and if not, which one changes? A door can be changed within limits — an over-large old bore can be covered by a wider escutcheon, a too-small bore can be re-drilled if stile width allows, a mortise pocket can be deepened if the case size permits. The lock can also be changed: some bodies sit on a cylindrical latch, some on a mortise case, some on a rim plate, and which family the SLK-8831 belongs to is a REQUEST line that determines everything else. A cylindrical-latch design, for example, makes backset a function of the latch body and largely frees the face geometry; a mortise-case design puts the pocket dimensions in charge. You cannot know which you are buying from a credential list.

Backset: How Far the Mechanism Sits From the Edge

Backset is the distance from the door's edge face to the centre of the bore or spindle line. It is the dimension most often "discovered" during fitting, because it is invisible on a closed door and obvious on an open one.

Commonly specified values in this trade are 60 mm (2-3/8 in) and 70 mm (2-3/4 in) in the ANSI world, 60 mm or 72 mm in metric mortise practice. What actually decides fit is not the list of values but the relationship between three things: the latch or deadbolt throw, the strike plate position on the frame, and whether the lock's body can be reversed or adjusted between backsets.

Situation found in the fieldCompatibility readingAction before ordering
Door backset matches the captured model requirementPasses the backset gateRecord the door ID; proceed on the strike-alignment check below
Door backset sits between two standard valuesModel-dependent — this is exactly where an adjustable-latch answer beats an assumptionAsk in writing whether the latch is backset-adjustable and over what range REQUEST
Existing strike plate and box are set for the old lockGeometry inherited, not chosenConfirm whether the new latch centreline coincides; if not, the frame gets re-worked — that is scope, not luck
Deadbolt throw does not clear the strike face on a test fitMechanical bind, not an electronics faultVerify backset and frame rebate before blaming the motor
Replacing a lock on a door with an old bore far from the edgeTwo independent dimensions now in tension (backset and stile width)Route as a documented prep decision or a different model

Decision rule: a backset answer that is not accompanied by a latch-body type is not an answer. Ask for the latch drawing. Ask for the deadbolt throw. Ask what happens if the frame is 4 mm out — because on old buildings it usually is, and a door that has dropped on worn hinges will fight a latch that fit perfectly on the drawing.

One more subtlety for electric mechanisms: on a motorised bolt, the strike is not just a hole. Misalignment loads the motor, and the lock reports the resulting failures as dead batteries, refused cards or a fingerprint that "doesn't work". Before you conclude that an electrical fault exists, prove the mechanical path: latch throws freely by hand on an open door, bolt enters the strike without the door being lifted, hinges are not worn. Door-fit errors launder themselves into electronics complaints — this is the single most common misdiagnosis in the field, and it is why the survey is worth the labour.

Stile Width and the Narrow-Door Exception

The lock-edge rail — the horizontal member the bore is drilled into — is the silent gate. A 60 mm cross bore needs more than 60 mm of solid material, because the bore has to be centred with a margin and through-fixings must land in sound timber or profile, not in a void.

Where short rails come from, and what to do with each:

  • Old apartment doors built with light framing; rails that narrow toward the bottom.
  • Moulded-skin doors where the "stile" you measured on the face is a pressed detail, not structure.
  • Shaped and arch-top doors, where the hardware position falls at a curve.
  • Sliding and pocket doors with a minimal edge to grip.
  • Aluminium and uPVC section doors, where the rail is a hollow chamber with a thin wall.
  • French/double-leaf pairs, where the active leaf carries a astragal rather than a rail.

Measure at the exact hardware height, on the lock-edge face, on both sides, and record the narrower reading. Then treat anything you would not happily drill into as an exception population rather than a detail.

The catalog contains a model class built for exactly this problem — a narrow-edge 4-in-1 electronic lock published with a waterproof body — which is the honest way to answer "what if our doors are too narrow?": the answer is a different engineered lock, confirmed against your measured rail width, not a smaller washer. Fit answers move between models only through written envelopes, never through category association. Making 79 models does not make one model's dimensions another model's dimensions.

Handing: Four Ways a Door Can Be Wrong

Handing is the least engineered item in most buyer conversations and the most frequently discovered at the door. A digital lock is not rotationally symmetric: the exterior housing belongs outside, the interior assembly inside, the lever points a way, the latch bevel faces a way, and the strike sits on a jamb.

Classification, from the hinge face (the side you can see the hinges on with the door closed):

Observation from the hinge faceClassificationWhat it changes for a 5-in-1 digital lock
Hinges on the right, door swings away from youRight hand (RH)Exterior unit face, lever direction, strike jamb side
Hinges on the left, door swings away from youLeft hand (LH)Mirror of the above
Hinges on the right, door swings toward youRight hand reverse (RHR)Exterior assembly may foul the jamb stop on opening; check clearances
Hinges on the left, door swings toward youLeft hand reverse (LHR)Same clearance question, mirrored
Metric/European practiceDIN right / DIN left, plus inward or outward openingSame four-way information in the convention your door schedule uses

Then the four consequences a survey must record:

  1. Does the lock ship handed, or does it adapt? Some bodies let you reverse the latch and re-orient the lever; some are supplied as LH or RH versions. This is a REQUEST line and it is a blocking one — order the wrong handedness and the shipment is scrap for that population.
  2. Latch bevel and strike preparation. Butt edges on prehung ANSI doors are commonly beveled around 2° (roughly 1/8 in over 4 in); metric butts are frequently square. Confirm the case's bevel tolerance rather than trusting a filing to fix it later.
  3. Which face takes the weather. An outward-opening exterior unit gets rain, sun and dust on the side that carries the reader and the keypad. Ingress protection is a model-published line — REQUEST it, do not infer it from a "waterproof" word attached to a different model class.
  4. Clearance and grip geometry. On a reverse-hand door in a recessed entry, the exterior assembly can end up awkward to reach or the handle can end up on the wrong side of the reader relative to the user's natural grip. Look at the mounting diagram for your handedness, not a marketing render.

The Sixth Condition: What the Dimension Sheet Does Not Cover

Five dimensions are numbers. The sixth is a list of conditions that void the numbers, and it belongs on the same survey sheet because every one of them has ended a project.

Condition foundWhy it matters to a digital lockWhat the survey records
Warped, bowed or sagging leafThickness varies across heights; latch fights a moving geometryMin/max per door, hinge wear noted, door gap measured
Fire-rated or security-rated assemblyNew bores are a question for that door's own certificate and your local authority — not for the lock supplierRated-leaf flag; exception routing; authority sign-off
Hollow-core leafFixing pull-out, case distortion when torquedCore type, backing/spacer plan, who signs it
Metal skin, aluminium or uPVC profileRadio path through metal, screw retention in thin wall, chamber geometryMaterial, wall thickness, insert/reinforcement plan
Glass panel in or beside the leafCannot be bored; the hardware zone may be adjacent to a glazed areaPanel position, distance from bore centre
Existing plugs, fillers, previous conversionsThe bore you measure may sit in repaired materialHistory note, photograph, decision on cutting into it
Rebated double-leaf, astragals, floor springs, electric closersStrike geometry and lever continuity change entirelyHardware-on-door inventory, closer type
Frame out of square, strike box already cutThe lock is blamed for what the frame didFrame measurement, rework scope
No clear interior access for power/battery serviceFive-credential locks still need batteries; the interior assembly must stay reachableInterior clearance and service-path note

A door that fails any of these is not "incompatible with the SLK-8831" — it is a project decision with a named owner. Some resolve by preparing the door deliberately, documented and signed. Some resolve by moving that population to a different model class. Some should resolve by not putting a digital lock there at all, and an honest compatibility document is the one that gives you permission to say so.

Five Credential Methods, Five Hardware Dependencies

The SLK-8831's declared identity is its five unlocking methods. From a door point of view, that is five separate sets of demands on one leaf, and each one converts into a survey question.

Declared methodWhat it asks of the doorQuestion for the supplier
FingerprintReader face on the exterior side: exposure to rain and sun, sightline, thumb reach, protection from being scuffed by the stop on a reverse-hand openingReader position within the exterior assembly, and how handing relocates it
PasswordKeypad region on a flat, unobstructed face, at a usable height; housing depth added to the leafFace clearance required and total projection from the door on both sides
RFID cardA reader zone whose position, read distance and card type are properties of the model, not the categoryCredential technology and read range published for this model REQUEST
Mechanical keyA cylinder or keyway through the leaf whose length depends on thickness, plus key access from outside and custody of key blanksCylinder type and length range, keys per unit, re-keyability
App / phone controlA radio path through or around the door, and a phone close enough to use it; metal skins and remote entries make this harderPlatform binding, radio type, effective range at the door, gateway requirements

Note what the table does not claim. Catalog-wide, the factory's models use fingerprint, passcode, RFID/IC card, mechanical key, app and Bluetooth, remote control, face recognition, hotel PC software and camera-based methods; the published category counts are 37 fingerprint models, 18 keypad, 9 RFID, 10 outdoor and 3 glass among the 79 models. Which of those technologies sit inside the SLK-8831's five methods is a per-model question. "It has card access" does not tell you 125 kHz or 13.56 MHz, does not tell you read distance, and does not tell you whether your existing card fleet works with it — all three of which are compatibility facts a distributor with installed credentials cares about far more than a marketing phrase.

The Compatibility Dossier: Blanks Filled in Writing

Here is the deliverable. Two columns of values meet in the middle: yours from the survey, the supplier's from the model. No row may be closed on either side by assumption, and a row with an empty right-hand cell is a blocking item, not a footnote.

Dossier lineYour measured value (from register)Supplier commitment to obtain REQUESTAcceptance rule
Supported door thickness bandMin/max per doorPublished min–max for this modelRegister extremes must sit fully inside the band, at every door
Cross-bore diameter requiredExisting bore Ø per doorRequired Ø, in mmReuse, enlarge (if rail allows) or new cut — recorded per population
Edge bore / latch boreExisting ØRequired ØSame decision logic as cross bore
Mortise pocket or cut-out sizePresent or absentPocket length × depth, drawing suppliedCutting scope signed before ordering
Backset requirementEdge-to-centre per doorFixed value or adjustable range REQUESTEither an exact match or an adjustable range that covers it
Latch-body familyDoor prep traditionMortise case / cylindrical latch / rimDetermines the whole cutting conversation
Cylinder line (key override)Thickness again, plus keyway accessCylinder type and usable length rangeMust span measured extremes with interior clearance
Spindle / follower size and length—Square size, length rangeCut from measured thickness, never nominal
Minimum lock-edge material widthNarrowest rail measuredMinimum stile width REQUESTAny door below it becomes an exception population
Handing adaptabilityLH/RH/RHR/LHR counts per populationShips handed, or adaptable both waysBlocking — wrong answer mis-orders a population
Projection from both facesClearance available inside and outExterior and interior projectionInterior must clear walls, stops, glazing beads
Environment rating for the mounting faceInterior / exterior / recessed per doorIngress and temperature limits for this modelExterior-facing units need a published line, not an adjective
Radio/app conditionsMetal skin? remote entry? thick leaf?Platform, radio type, range at doorField test on a real door before fleet order
Power accessInterior clearance, service pathBattery type, access side, low-power indicationServicing must be possible with the door closed
Emergency and mechanical fallbackKey custody planKey count per unit, re-key routeWritten before the program, per the override guide
Template and drawings—Template supplied as a documentNo template, no field-cutting commitment

That sheet is the compatibility answer. Twelve of those rows are the ones a supplier can quote from a datasheet in a morning; the buyer who receives a reply that dodges half of them has learned something useful about the supply relationship before money moved.

Survey Register: One Row Per Door

The dossier holds the model side. The register holds the door side, and it is the document that justifies a split order — or a refusal.

Door IDBuilding / floorThickness min / max (mm)ToolCross bore ØBacksetRail widthHandingFace materialPrep conditionVerdict
EXAMPLE — A-204Block A / L244 / 44.5Caliper6072105RHTimber, solid coreCleanFits as ordered
EXAMPLE — A-118Block A / L144 / 45Caliper546096LHRTimber, solid coreOld 54 bore, plug visibleFits with documented prep
EXAMPLE — C-011Annex / GF51 / 52Rulenone—58Outward, metal skinAluminium profile, hollowNo prepNot this model — exception
EXAMPLE — B-3FBlock B / stair43 / 43Caliper607088RHRated assemblyDo not cut without assessmentBlocked — rating question

Three verdicts, and only three, so the register cannot drift into opinion:

VerdictEvidence requiredConsequence for the order
Fits as orderedAll six conditions inside the captured commitments; no voiding conditionCounts into the standard line item
Fits with documented prepAll dimensions inside except one, with a named treatment (fill, plate, re-bore, strike rework) signed by a personStandard line item plus a prep scope line, scoped and owned separately
Not this model / blockedAny condition outside the envelope, an unresolved blank on the dossier, or a rating/authority questionRemoved from this line item; routed to another model class or to the authority; never ordered on hope

Blank-cell rule: a door cannot receive "fits as ordered" while any dossier row on the model side is still empty. That is the discipline that separates a survey from a guess with decimals.

An Illustrative Scenario: 46 Units, Three Door Vintages

Consider a hypothetical 46-unit walk-up block being fitted with 5-in-1 digital locks across three entrance types: unit entrance doors, a stairwell fire door at each landing, and one main external door onto the street.

The sales assumption before survey was one line item — 46 locks. The register told a different story. Unit doors were a homogeneous population: 43–45 mm, Euro-profile mortise prep at 72 mm PZ, 72 mm backset, 100 mm-plus rails, DIN right, opening inward. Twenty-eight of them closed as fits as ordered once the dossier rows for backset, cylinder length and handing adaptability came back in writing — and the handing row was the one that nearly killed the order, because the supplier's first reply said "reversible" and the second, pushed for a drawing, said the lever must be re-oriented at assembly. That is a labour scope, not a spec.

Nine unit doors had a legacy 54 mm cross bore from an older cylindrical set. All nine sat inside the required geometry, so they took a documented prep treatment — wider escutcheon on the interior face, supervisor's name against each ID — and became fits with documented prep, each with a line item for the plate instead of an argument at the door.

The landing fire doors were the hard stop. Fourteen leaves, correctly bored, correct backset — and a rating on the door set whose certificate governs any new hole. Those went off the program as blocked, not incompatible, to be answered by the fire-assessment route with the door's own certificate holder. The main street door had its own answer: outward-opening, weather on the exterior unit, a metal-edged leaf and a phone-based entry expectation for a delivery person standing two metres away. Its dossier rows for environment rating and radio range came back empty in the first reply, so it moved to an exception file.

The order that resulted had four conversations instead of one, all of them in week two rather than month four. That is what a six-condition survey buys: a worse-looking spreadsheet early, and a shipment that fits.

Closing the Loop Before the Purchase Order

A completed dossier plus a signed register is the whole qualification stage, and it converts into two cheap physical checks before anything is bought in quantity.

The first is a pilot on a real door, not a bench. Pick the worst borderline member of each population — the narrowest rail, the odd backset, the reverse-hand door, the outward-opening one — and fit one unit there. A pilot on a good door proves nothing except that the box was complete. Second, a credential walk on that installed pilot door: all five declared methods, tested through the closed door, including the mechanical key on the actual leaf (the last credential tested is usually the one that saves the project). Battery access, handle feel against the stop, latch behaviour with the door lifted and dropped, and the phone-based method attempted from realistic standing positions with the leaf and frame that exist.

That is the sequence. Measure in six dimensions, capture the model's commitments in writing, bucket by rule with only three verdicts, and refuse to let an empty cell become an order line. The execution timeline on the other side of the decision — stage-gate fitting, enrollment order and commissioning signatures — is worked through in the SLK-8831 installation guide, and the model's commercial case in the complete buyer guide. Cross-population retrofit programs will recognise this survey discipline from the hotel lock replacement stage-gate guide, and the category's wider fingerprint-model range is at fingerprint door locks.

Send the dossier and the register together through the quote request so the answer comes back against your actual doors, and pull a physical pilot for the worst borderline population through order-samples before the program line is signed. A supplier who answers twelve blank cells with numbers is a supplier you can plan with; one who answers them with adjectives told you something too — earlier, and for free.

장바구니
쿠키를 허용하면 이 사이트에서의 이용 경험이 개선됩니다. 쿠키 정책
Chat on WhatsApp