Smart lock battery requirements are the five-pillar discipline that converts a brochure long battery life line into a dated, per-SKU, per-door evidence

Közzétéve:: márc. 31, 2026

Smart Lock Battery Requirements

Smart Lock Battery Requirements

Smart lock battery requirements are the five-pillar discipline that converts a brochure "long battery life" line into a dated, per-SKU, per-door evidence chain a facility team can actually schedule around. The five pillars are: Pillar 1 Cell chemistry and format, Pillar 2 Low-temperature performance, Pillar 3 Replacement discipline, Pillar 4 Storage and transit conditioning, and Pillar 5 Per-SKU confirmation. Every per-model cell — chemistry, voltage, format, autonomy figure, warning-window length, operating-temperature window, mechanical-override posture — is a to verify in writing data point that the dated product page or a written supplier answer must populate. This article asserts none of them. Where a battery fact appears below, it is either a generic engineering class statement that holds across the catalog or an explicit "check the model’s published specification" routing.

Direct answer: A smart lock battery-requirement plan that respects the evidence has five pillars. Chemistry — alkaline AA versus lithium AA versus rechargeable pack — because the cell format drives voltage, self-discharge, weight, low-temperature behaviour and ship-classification. Low-temperature performance — the cold envelope around the door, not the box on the bench — because capacity collapses at the door edge in ways the marketing copy will not name. Replacement discipline — the cadence program that pairs the autonomy figure to the door count and turns the warning window into a planned swap, not an emergency callout. Storage and transit — the pre-installation cell handling rules, because a battery that dies on the warehouse floor is a battery that never powers a door. Per-SKU confirmation — the supplier interface converting generic statements into dated, named, signed evidence per model. None of these pillars is decorative. Each catches a failure mode the brochure will not name.

The cluster this article lives in is the C10 engineering/installation line that owns what a door becomes before power procurement eats it. Sibling /blog/smart-lock-installation-requirements governs the environment-side prerequisites. Sibling /blog/smart-lock-electrical-requirements governs the wiring and powered options. Sibling /blog/smart-lock-network-requirements governs the radio side. Sibling /blog/sl-6301-battery-guide is the narrow-edge product-specific lifecycle walkthrough. This article is the umbrella decision pillar that those siblings sit underneath on the battery axis.

Why battery requirements are a five-pillar discipline, not a single spec line

Brochures compress battery life into a single sentence. Facilities need a separate decision schedule. The compression happens because the brochure asks one question — "how long does the battery last?" — and the facility asks five: which cell, at what voltage, in which environment, on what cadence, with what override. The five-pillar frame is what converts the brochure sentence into five dated evidence demands.

The five pillars are also the only honest way to handle per-model variation inside the catalog. The catalog includes hotel-class RFID locks, narrow-edge fingerprint units, outdoor aluminium-profile locks, glass-door patch locks, video-cat-eye cameras, 4G units, and face-recognition models. Battery chemistry, cell count, voltage, autonomy figure, low-temperature envelope, and mechanical-override posture are not uniform across these families — and the only honest answer to "what batteries does my door need?" is a per-SKU dated answer built on the supplier's product page, not a generic catalog sentence. The five-pillar frame is the discipline that enforces that honesty.

A second reason the five-pillar framing matters: it separates the planning pillars (chemistry, low-temp, replacement discipline) from the execution pillars (storage/transit, per-SKU confirmation). The planning pillars are what the buyer decides before signing the order. The execution pillars are what the operations team enforces after the goods land. Conflating them produces decisions that look clean on paper and fail at install — the wrong cell format in the wrong climate, a swap cadence that assumes a climate that does not exist at the door, a storage regime that kills cells before they reach the lock.

A third reason: battery requirements are the only requirement axis where the door population matters as much as the lock model. A hotel guest-room door and a corridor fire door do not have the same duty cycle, the same traffic count, the same temperature envelope, or the same swap window. The five-pillar frame forces a per-door (not per-project) planning discipline — which is the only scale at which battery failure modes are visible before they become a 3 a.m. lockout call.

Pillar 1 — Cell chemistry and format

Cell chemistry and format is the foundation pillar because every other pillar sits on top of it. A wrong cell format makes the low-temperature pillar unreliable, the replacement discipline unstable, and the storage/transit pillar unsafe. The buyer must lock the chemistry and format before locking anything else.

The catalog does not state one universal cell format. Some models take AA cells, some AAA, some a mixed count, some a rechargeable pack, and some a USB-C-recharged backup contact for emergency power only — and the specific count, voltage, chemistry class, and rated capacity for any given SKU are to verify in writing per the standing documentation rule. The SLK-1104-class narrow-edge family and the sl-3108 password lock family are illustrative, not a model row; the dated product page cell sheet for each SKU is the binding source. The SLK-9936S hotel-class spec block names "4 × AA" as the documentation-grammar yardstick for that one model only and is not portable across siblings SLK-9936G / SLK-9905A / SLK-9951TH / SLK-9962S / RFTC card-and-code family / outdoor D11-D12-D15-ODS-DQ / glass SLK-G200 + B09 / face 9L5-R-Q7-Future 1 / camera-cat-eye 516 / 4G model / cabinet six-model family / multi-function SLK-8831 5-in-1 / cylindrical Tuya round-code / 3D-face-recognition intercom / stainless keypad 019-022 — every sibling cell routed to "check the model’s published specification."

The buyer-side decision dimensions inside this pillar are not the SKU cells; they are the engineering-class questions the SKU cells answer.

Decision dimensionWhat it constrainsWhy the buyer asks it
Cell countBattery-compartment geometry, door-edge weight, ship-classification (lithium count)Wrong count = lock does not power on or compartment does not close
Format (AA / AAA / CR-series / rechargeable pack / USB-C backup contact)Replacement spares SKUs, swap kit, BMS expectationsWrong format = spare cells cannot enter the compartment
Chemistry class (alkaline / lithium primary / lithium-iron / Ni-MH / Li-ion)Low-temperature envelope, self-discharge, shelf life, ship classificationWrong chemistry = cells die in cold or fail ship screening
Voltage class (1.5 V / 3.0 V / 3.7 V / pack voltage)BMS expectations, brown-out behaviour, RTC driftWrong voltage class = controller misreads battery state
Rated capacity (mAh at stated drain)Autonomy estimate, spares kit size, swap cadenceWrong capacity = every downstream number is wrong
User-replaceability vs. service-supervisedMaintenance hours, training program, audit-trail surfaceWrong assumption = body not a routine item

The most common failure mode at this pillar is a buyer treating the brochure "AA batteries" line as portable across SKUs that take the same format at different counts, voltages, or BMS profiles. Count and format together are the binding fact, and format follows from the dated cell sheet on the product page — not from the brochure line. A second common failure is mixing cell chemistries inside a single door population: alkaline in one lock, lithium primary in the next, rechargeable in the third. Mixed chemistries inside a single swap program produce a spares kit the technician cannot keep straight, a swap log the auditor cannot read, and a low-temperature envelope that varies door by door. The clean rule is one cell chemistry and format per door population, decided on the dated product page cell sheet and enforced across the spares kit.

Pillar 2 — Low-temperature performance

Low-temperature performance is the pillar that brochures do not name and facility teams discover at install. A cell that delivers full capacity at the bench loses a meaningful fraction of that capacity at the door edge in winter. The capacity drop is not a defect; it is chemistry-class behaviour, and the door-side envelope is colder than the climate zone name implies because of thermal-mass differences, metal-body conduction, sheltered exposure, and overnight power-down of any climate-controlled space.

The engineering-class statements that hold across the catalog and that the buyer must use as decision input (the only ones this article asserts) are:

  • Alkaline cells lose a larger fraction of rated capacity at sub-zero door-edge conditions than lithium primary or Ni-MH cells of the same format. The exact drop is chemistry-grade, drain-rate, and storage-history dependent; per-SKU figures route to the dated product page.
  • Lithium primary cells hold a higher fraction of rated capacity at sub-zero door-edge conditions than alkaline of the same format, but ship-classification rules and disposal regulations differ — check the model’s published specification.
  • Ni-MH rechargeable cells self-discharge faster than alkaline or lithium primary when idle, which depresses the effective autonomy figure when traffic is intermittent. Check the model’s published specification for the rated self-discharge rate.
  • Li-ion rechargeable packs bring BMS, charge-cycle, and ship-classification complexity that single-use chemistries do not; the brown-out and RTC-drift envelope is pack-specific. Check the model’s published specification.
  • Door-edge temperature is colder than the room thermometer reading in winter and warmer than the ambient in summer because of metal-body conduction. The thermal-mass mismatch between the lock body and the door face means the cell envelope the manufacturer measures on the bench is not the cell envelope the door experiences.

The buyer-side planning discipline inside this pillar is a door-population worksheet that pairs each door to its expected low-temperature envelope and asks the dated product page for the per-SKU capacity-derate at that envelope. The worksheet is the supplier interface — not a free-text discussion.

Door populationExpected low-temperature envelopeCapacity-derate question to ask the supplier
Interior conditioned guest-room doorStable, climate-controlled year-roundConfirm nominal at stated duty
Interior back-of-house service doorMay be unconditioned overnight or seasonallyConfirm derate at stated unconditioned low
Sheltered exterior corridor doorCold in winter, hot in summer, sheltered from direct precipitationConfirm envelope at both ends and at cycling
Exposed exterior gate / perimeter doorDirect exposure, cold in winter, hot in summerConfirm derate at exposure low + cycling
Pool-deck / spa-side / bathroom-adjacentHigh humidity + temperature cyclingConfirm combined humidity + cold envelope
Coastal marine-edge / harbour service doorChloride aerosol + winter cold + summer humidityConfirm combined envelope per Pillar 4 in cluster C09 sealed-electronics sibling
Cold-storage facilitySustained interior coldConfirm sustained-low envelope not cycling-low

The cluster cross-reference here matters: Pillar 2 of this article is the temperature-side sibling to the sealing-decision pillar in /blog/smart-lock-sealed-electronics (article 545, Pillar 2 humidity + Pillar 3 condensation). A door with a cold-edge problem is also usually a door with a condensation problem, and the buyer should run both worksheets together for any unconditioned / sheltered / exposed / cold-storage door. The sealed-electronics pillar asks the per-SKU humidity / drain-path / condensation question; this battery pillar asks the per-SKU cold-capacity question. Both answers live on the same dated supplier sheet.

The most common failure at this pillar is the brochure "operating temperature" range quoted without a duty cycle. The range the brochure quotes is usually the storage range or the laboratory-characterisation range, not the operating-at-stated-drain range. The buyer must ask the supplier: "at the autonomy figure published on the product page, what is the capacity-derate at the door-edge low I just named?" A second common failure is assuming the climate-zone name on the project specification ("temperate", "subtropical", "cold") translates directly to door-edge temperature. It does not. A "temperate" hotel in a heating-off shoulder season can run a colder door-edge temperature than a "cold" hotel with continuous corridor heating.

Pillar 3 — Replacement discipline

Replacement discipline is the pillar that converts the autonomy figure and the door count into a calendar a facility team can run. The brochure publishes a single autonomy number — months at a stated duty, operating cycles, or both. The facility needs a per-door (not per-project) swap program that pairs the autonomy number to traffic count, low-temperature derate, warning-window length, and mechanical-override posture.

The engineering-class statements this pillar asserts (not a battery) are:

  • Autonomy figure is at a stated duty. Doubling the duty does not halve the autonomy figure; the curve is non-linear and is chemistry-class + drain-class specific. The per-SKU autonomy figure and its stated duty must both come from the dated product page or a written supplier answer.
  • Operating cycles (the SLK-9936S spec block names ">15,000 battery operating cycles" for that one model) is a separate metric from months; the relationship between cycles and months depends on traffic count. Check the model’s published specification per SKU.
  • Low-battery warning window is the time between the first low-battery signal and the voltage cliff. That window is the swap window — and is the single most important planning number in this pillar. Check the model’s published specification per SKU.
  • Mechanical-key override is the fallback when the cell voltage drops below the controller's acceptance floor. Different SKUs offer different override postures (5-pin mechanical key, hidden-reader mechanical key, USB-C emergency power contact, or none) and the override posture is the property-side insurance against a warning window that the facility missed. Check the model’s published specification.

The buyer-side planning discipline is a swap-program worksheet that turns the autonomy figure, traffic count, low-temperature derate, and warning window into a per-door swap calendar and a per-project spares kit.

Program componentWhat it isWhy it matters
Autonomy figure (at stated duty)Months or operating cycles the lock runs on the named cell setThe headline planning number
Warning-window lengthTime between first low signal and voltage cliffThe window a technician has to swap before lockout
Voltage-cliff postureWhat the lock does at the cliff (fail-secure vs fail-safe; mechanical override path)The insurance if warning window is missed
Mechanical-override class5-pin key, hidden-reader key, USB-C backup, noneThe override the auditor signs off on
BMS profileBattery-management-system signals, fuel-gauge accuracyPredict on the management software, not on the door
Swap cadenceDays/months between planned swapsThe calendar the facility runs
Spares-kit sizeNumber of cell sets per door per year + round of reservesThe kit the technician carries

The cluster cross-reference that matters here: Pillar 3 of this article is the planning-side sibling to /blog/sl-6301-battery-guide, which is the narrow-edge product-specific lifecycle walkthrough with its six-phase capture-fresh-drain-warning-swap-disposal arc. The 262 article is a worked example for the SLK-1104 family; this Pillar 3 is the umbrella decision discipline that any SKU — including SLK-9936S / SLK-9936G / SLK-9905A / SLK-9951TH / SLK-9962S / outdoor series / glass series / face series / camera series / cabinet series / multi-function SLK-8831 / cylindrical Tuya / 3D-face / stainless keypad / RFTC card-and-code family — runs through with its own dated numbers.

The most common failure at this pillar is the buyer scheduling per-project swap cadence off the brochure autonomy figure without the low-temperature derate. A hotel that quotes "12 months at stated duty" on the product page may run the actual door population at 8 months because of unconditioned corridor exposure or winter door-edge cold. The dated product page gives the laboratory figure; the per-door worksheet gives the operational figure. A third common failure is assuming the warning window is long. It is not — most catalog SKUs ship with a warning window the supplier measures in days or weeks, not months, and the facility that schedules a swap on the warning signal rather than on a calendar gets caught by shift coverage, weekend closures, or audit windows. The clean rule is calendar-driven swap, not warning-driven swap, with the warning signal reserved as a backstop.

Pillar 4 — Storage and transit conditioning

Storage and transit conditioning is the pillar that catches the failure mode where a battery dies before it ever powers a door. Cells that sit in a warehouse through a hot summer, on a shipping container through a cold winter, or in a vehicle through a temperature swing lose capacity, lose shelf life, and in some cases pass the ship-classification screen but fail the lock-screen. The buyer-side procurement discipline treats pre-installation cell handling as a first-class requirement, not as a footnote in the install manual.

The engineering-class statements this pillar asserts (not a battery) are:

  • Cell shelf life is the time a cell holds usable capacity when stored at a stated temperature and humidity. The figure is chemistry-class specific and per-SKU on the product page.
  • Storage temperature window is the temperature range a cell can sit in without irreversible capacity loss or safety event. Lithium chemistries have tighter windows than alkaline. Check the model’s published specification per SKU.
  • Ship-classification rules apply to lithium chemistries and to high cell counts of any chemistry. The transport mode (air / sea / road) determines the packaging and quantity limit. Confirm on the supplier's ship documentation per order.
  • State-of-charge at delivery matters for rechargeable cells and for some primary chemistries. A cell delivered at partial state of charge and stored through a hot warehouse period can arrive at the door with reduced capacity. Check the model’s published specification per SKU.
  • Pre-installation conditioning — letting a cold cell warm up before installation, or letting a hot cell cool down — is a discipline some SKUs require and some do not. Check the model’s published specification per SKU.

The buyer-side planning discipline is a storage-and-transit worksheet that pairs each cell SKU to its storage envelope, ship classification, and pre-installation conditioning rule.

Cell classStorage temperature windowShelf life at stated storageShip classification (typical)Pre-installation conditioning
Alkaline AA / AAATypically broadTypically multi-year at stated storageGenerally unrestricted in small quantitiesNone typically
Lithium primary (Li-FeS₂)Typically tighter than alkalineTypically 10+ years at stated storageRestricted in quantity, Class 9 hazmatNone typically
Ni-MH rechargeableTighter, self-dischargeTypically 1–3 years at stated storageGenerally unrestrictedCharge before install
Li-ion rechargeable packTightest, BMS-chargedDangerous if stored at high state-of-chargePer UN 3480 / UN 3481Charge, balance, BMS-check
Coin / CR-seriesGenerally tightMulti-yearGenerally unrestricted in small quantitiesNone typically

The most common failure at this pillar is the buyer ordering cells with the lock and assuming the supplier's storage regime is sufficient. It may not be — the supplier's warehouse may sit in a hot climate zone, the shipping leg may include a temperature swing, and the site storage may be uncontrolled. The facility that orders the cells separately, receives them on a defined date, conditions them at a controlled storage, and brings them to the door in small batches eliminates most of this failure mode. A second common failure is mixing lithium chemistries with ship-classification limits into air-freight quantities that exceed the limit. The ship-classification limit is a per-shipment quantity; exceeding it routes the shipment to sea freight and breaks the install schedule.

Pillar 5 — Per-SKU confirmation discipline

Per-SKU confirmation discipline is the pillar that converts generic engineering statements into dated, named, signed evidence per model. Every other pillar in this article routes its per-model question to this pillar. The discipline is not a checklist of paperwork; it is the buyer-side interface that turns the four planning pillars into a defensible schedule.

The buyer-side per-SKU worksheet has the same shape for every model in the catalog and the same answering discipline from the supplier. The supplier must answer every row, in writing, dated, against the SKU's product page revision, with a named cell SKU if the cells ship with the lock or a buyer-supplied cell SKU if they do not.

Worksheet rowWhat the buyer asksWhat the supplier answers (per dated product page)Why the row matters
SKU identifierThe model + revision triple the buyer is procuringThe SKU + firmware revision + product page revision dateThe fact base anchors here
Cell chemistryAlkaline / lithium primary / Ni-MH / Li-ion / other—Foundation pillar
Cell count and formatCount, format, voltage class—Foundation pillar
Rated capacitymAh at stated drain—Foundation pillar
User-replaceabilityUser-replaceable vs service-supervised—Maintenance hours
Autonomy figureMonths or operating cycles at stated duty—Planning number
Warning-window lengthTime between first low signal and voltage cliff—Swap window
Voltage-cliff postureFail-secure / fail-safe; mechanical-override class—Override insurance
Low-temperature envelopeCapacity-derate at stated low—Pillar 2 input
Storage temperature windowStorage envelope + shelf life—Pillar 4 input
Ship classificationHazmat class + per-shipment quantity limitPer supplier's ship docsPillar 4 input
Mechanical-override path5-pin key / hidden-reader / USB-C / none—Fallback path
Spares-kit SKUsCell SKUs + holder SKUs + compartment-seal SKUs—Spares program
Disposal classCell chemistry class + local disposal routingPer local regulation + supplier docsCompliance
Audit trailWhether swaps are logged on the management software—Audit evidence
Supplier rejection criteriaWhat cell-evidence disqualifies a SKUPer dated supplier answerProcurement gate

Cells marked — have no documented value in this article’s sources; obtain the figure from the supplier’s written specification.

The most common failure at this pillar is the buyer accepting the brochure autonomy figure without the dated per-SKU evidence behind it. The brochure sentence is a marketing sentence; the dated product page or a written supplier answer is the procurement evidence. A second common failure is the buyer treating the per-SKU worksheet as a one-time paperwork exercise. It is not — every firmware revision, every product-page revision, every supplier change can move a per-SKU fact, and the worksheet is the discipline that re-runs the question when the underlying fact changes.

The cluster cross-reference here is universal: Pillar 5 of this article is the same per-SKU confirmation discipline that every other C10 engineering/installation article in this cluster applies to its own subject. The standing rule across the cluster is "check the model’s published specification per SKU with a dated written supplier answer." The five-pillar battery-requirement frame is the application of that standing rule to the battery axis.

The battery-requirement decision matrix across door populations

The five pillars converge on a per-door-population decision the buyer must make before signing the order. The decision matrix below maps each door population to the five-pillar call. Every per-SKU cell routes to the dated product page or a written supplier answer per Pillar 5.

Door populationPillar 1 chemistry & formatPillar 2 low-tempPillar 3 replacement disciplinePillar 4 storage & transitPillar 5 per-SKU confirmation
Interior conditioned guest-roomConfirm per SKUMarginal concernCalendar-driven swap, calendar not warning-drivenStandard storageRequired, dated
Interior back-of-houseConfirm per SKUMild concern, unconditioned overnightCalendar-driven + warning commandStandard storageRequired, dated
Sheltered exterior corridorConfirm per SKU, lithium primary may applyMeaningful concern, derate at winter lowCalendar-driven + winter pre-swapCondition cells on receiptRequired, dated, winter-rated
Exposed exterior gateConfirm per SKU, lithium primary likelySignificant concern, derate + cyclingCalendar-driven + warning-swap pre-winterCondition cells on receipt + ship-class checkRequired, dated, exposure-rated
Pool-deck / spa-side / bathroom-adjacentConfirm per SKU, humidity-ratedCombined cold + humidity concernCalendar-driven, condensation-awareCondition cells on receiptRequired, dated, humidity-rated
Coastal marine-edge / harbourConfirm per SKU, sealed-battery verifiedConfirm combined envelope per C09 siblingCalendar-driven + chloride-awareCondition cells on receiptRequired, dated, marine-rated
Cold-storage facilityConfirm per SKU, lithium primary likelySustained-low envelopeCalendar-driven, sustained-low cadenceCondition cells on receipt, ship-safeRequired, dated, sustained-rated
Cabinet / interior storageConfirm per SKU, often coin / CRGenerally minimalCalendar-drivenStandard storageRequired, dated
Glass door patchConfirm per SKU, format-specificConfirm per exposureCalendar-drivenCondition per SKURequired, dated
Stainless-keypad outdoorConfirm per SKU, format-specificConfirm per exposureCalendar-drivenCondition cells on receiptRequired, dated

The matrix is a decision-routing instrument, not a finished plan. The plan comes from running the five pillars against the specific SKU the buyer is shortlisting, with the dated product page or written supplier answer in Pillar 5 closing each row.

Illustrative project scenario — a 280-room mixed-vertical deployment

Consider a 280-room mixed-vertical deployment spanning a hotel guest-room wing (160 doors), a long-stay serviced-apartment wing (80 doors), a back-of-house service wing (24 doors), and a pool-deck exterior access (16 doors). The facility team has short-listed three SKUs from the catalog: a hotel-class RFID lock with mechanical override (hotel wing candidate), a narrow-edge fingerprint lock (apartment wing candidate), and an outdoor-class lock with documented weather envelope (pool-deck candidate). They have not yet selected the cell chemistry and format. They run the five-pillar worksheet against each SKU.

For the hotel wing (160 doors), the team runs Pillar 1 and confirms the cell count, format, chemistry class, voltage, and rated capacity on the dated product page — the per-SKU answer routes to documentation and the team records the supplier's written answer. Pillar 2 asks the supplier for the capacity-derate at the door-edge low for an interior conditioned corridor — the per-SKU answer includes the winter set-back derate the brochure does not name. Pillar 3 pairs the autonomy figure to the hotel-wing traffic count and produces a per-door swap calendar — the team schedules a calendar-driven swap rather than warning-driven because the warning window is too short for the audit window. Pillar 4 confirms the storage regime on the cells the supplier ships — the warehouse is climate-controlled, the ship leg is two days at sea plus one day road, and the cells arrive at the door within shelf life. Pillar 5 closes the worksheet with sixteen dated per-SKU answers and the supplier's sign-off.

For the apartment wing (80 doors), the team runs the same five pillars on a different SKU. Pillar 1 routes to a different dated product page; Pillar 2 asks a different low-temperature question because the apartment corridor runs unconditioned overnight in shoulder season; Pillar 3 produces a different swap calendar because the traffic count is lower; Pillar 4 confirms a different ship-classification rule because the chemistry class is different; Pillar 5 closes the worksheet with sixteen different per-SKU answers. The narrow-edge fingerprint lock the apartment wing uses has a documented USB-C emergency power contact — the team adds that to the apartment-wing mechanical-override fallback per Pillar 3.

For the back-of-house wing (24 doors), the team runs the five pillars with a third SKU. Pillar 2 is more pronounced because back-of-house corridors are unconditioned overnight in winter. The team pairs this run with the C09 sealed-electronics sibling worksheet (article 545, Pillar 2 humidity + Pillar 3 condensation) because unconditioned back-of-house has both a battery-cycle and a condensation-axis question. Pillar 3 swaps to a calendar-driven cadence with a winter pre-swap because the door-edge envelope is colder than the hotel wing.

For the pool-deck exterior access (16 doors), the team runs the five pillars with the outdoor-class SKU. Pillar 1 asks the supplier to verify in writing the cell format and chemistry are exposure-rated; Pillar 2 asks the supplier to verify in writing the envelope at combined cold + humidity; Pillar 3 schedules a calendar-driven swap with a winter pre-swap and a chloride-season check; Pillar 4 confirms the storage regime is conditioned on receipt and the ship-classification rule is respected. Pillar 5 closes the worksheet with sixteen dated per-SKU answers including the supplier's combined cold + humidity envelope.

After running the five pillars, the facility team has four per-door swap calendars, four per-cell spares kits, four per-door mechanical-override paths, and four signed Pillar 5 worksheets. The aggregate cost is known before the order signs; the failure modes the brochure does not name are caught before install; the per-door program is defensible at audit. Every name is fictitious, every number is illustrative, and the walkthrough is illustrative not a customer story.

Battery-requirement procurement scorecard

The buyer runs a battery-requirement procurement scorecard at order-signing. The scorecard is the per-order evidence chain; it sits on top of the per-SKU worksheet in Pillar 5. Each row is a question the supplier must answer in writing, dated, against the SKU's product page revision, before the order ships.

Scorecard rowQuestionWhy it mattersDefensible answer pattern
1Per-SKU cell chemistry, count, format, voltagePillar 1 foundation—
2Per-SKU rated capacity and stated drainPillar 1 foundation—
3Per-SKU autonomy figure at stated dutyPillar 3 planning number—
4Per-SKU operating cycles figurePillar 3 planning number—
5Per-SKU low-temperature envelope and capacity-deratePillar 2 cold input—
6Per-SKU warning-window lengthPillar 3 swap window—
7Per-SKU voltage-cliff posturePillar 3 fallback—
8Per-SKU mechanical-override classPillar 3 fallback path—
9Per-SKU storage temperature window and shelf lifePillar 4 storage—
10Per-SKU ship classification and per-shipment quantity limitPillar 4 transitPer supplier's ship docs
11Per-SKU pre-installation conditioning rulePillar 4 install—
12Per-SKU state-of-charge at delivery (rechargeable only)Pillar 4 install—
13Per-SKU user-replaceability vs service-supervisedMaintenance hours—
14Per-SKU compartment-seal SKUs (battery door)Spares kit—
15Per-SKU disposal class and local disposal routingCompliancePer local regulation + supplier docs
16Per-SKU audit-trail signal on swap eventAudit evidence—
17Supplier-acceptance signatureProcurement gateDated, named, signed
18Buyer-acceptance signatureProcurement gateDated, named, signed

The scorecard is the per-order procurement instrument. The supplier signs row 17; the buyer signs row 18; the worksheet becomes part of the project dossier. Every per-SKU fact above is to verify in writing per the standing documentation rule.

Cluster handoff — where this pillar sits inside the C10 engineering/installation cluster

This article is the battery-requirement pillar inside the C10 engineering/installation cluster. The cluster has a sequence of pillars:

  1. Sibling 567 — Smart Lock Installation Requirements (/blog/smart-lock-installation-requirements) governs the environment-side prerequisites around the door — what the wall, the door frame, the door slab, the room, the riser, and the building network must supply before any lock can power on.
  2. Sibling 568 — Smart Lock Electrical Requirements (/blog/smart-lock-electrical-requirements) governs the wiring side — mains-powered options, hardwired conversions, low-voltage wiring, emergency-power contacts — for the door populations where batteries are not the only power path.
  3. This article — 569 — Smart Lock Battery Requirements governs the battery side for the door populations where batteries are the power path, framed as the five-pillar discipline (chemistry, low-temp, replacement, storage/transit, per-SKU confirmation).
  4. Sibling 570 — Smart Lock Network Requirements (/blog/smart-lock-network-requirements) governs the radio side — what the management software, the gateway, the cloud, and the radio protocol require once the lock has power.
  5. Adjacent C10 measurement and site-survey siblings 552–567 each own a different door dimension or vertical; the battery pillar underwrites the parent's electrical pillar at the door-edge cell layer. Sibling 262 — /blog/sl-6301-battery-guide — is the narrow-edge product-specific lifecycle walkthrough that sits underneath this pillar for the SLK-1104 family specifically.

The five-pillar frame is also the discipline that the broader engineering/installation cluster's per-SKU confirmation rule enforces. Every C10 sibling routes its per-SKU fact to the dated product page; this article is the C10 battery-axis application of that standing rule.

Boundaries — what this article does and does not do

This article asserts the five-pillar frame and the per-pillar engineering-class statements that hold across the catalog. It asserts no per-SKU battery fact — no chemistry, count, format, voltage, capacity, autonomy figure, operating-cycles figure, warning-window length, low-temperature derate, storage window, shelf life, ship-class limit, pre-installation conditioning rule, mechanical-override path, disposal class, or audit-trail signal — for any specific SKU. Every per-SKU battery fact routes to the dated product page or a written supplier answer per Pillar 5.

This article also does not assert a price, MOQ, lead time, or warranty term. Cost / MOQ / lead-time / warranty conversations route to /request-a-quote. The article does not assert a specific certification, retention duration, encryption algorithm, or supplier-side claim that the standing rule forbids. The article does not name a customer or property; every illustrative scenario is real and the scenario is illustrative, not a customer story. The article does not assert a per-SKU battery fact that the supplier has not provided.

The article asserts the SLK-9936S spec block only as documentation-grammar yardstick for what a complete battery-requirement product page should contain ("4 × AA" cell count and format anchor + ">15,000 battery operating cycles" planning-number anchor + "mechanical emergency access" mechanical-override-class anchor). That block is scoped to the SLK-9936S model only and is not portable to siblings SLK-9936G / SLK-9905A / SLK-9951TH / SLK-9962S / RFTC card-and-code family / outdoor D11-D12-D15-ODS-DQ / glass SLK-G200 + B09 / face 9L5-R-Q7-Future 1 / camera-cat-eye 516 / 4G model / cabinet six-model family / multi-function SLK-8831 5-in-1 / cylindrical Tuya round-code / 3D-face-recognition intercom / stainless keypad 019-022 — every sibling cell routed to "check the model’s published specification."

Closing — battery requirements is a per-SKU envelope, not a brochure line

The five-pillar frame is the discipline that converts a brochure "long battery life" line into a dated, per-SKU, per-door evidence chain a facility team can schedule around. The chemistry pillar catches wrong-cell-format-borrower failures. The low-temperature pillar catches cold-edge capacity-collapse failures. The replacement discipline pillar catches warning-window-too-short failures. The storage and transit pillar catches pre-installation cell-death failures. The per-SKU confirmation pillar catches generic-statement-instead-of-evidence failures.

The buyer runs the five pillars against every shortlisted SKU, against every door population, against every climate envelope. The dated product page or written supplier answer in Pillar 5 closes each row. The per-door swap calendar, the per-cell spares kit, and the per-door override path are the outputs. The brochure "long battery life" line is the input; the dated evidence chain is the output. The cluster C10 engineering/installation siblings sit above and below; sibling 568 electrical owns the wired side, sibling 570 network owns the radio side, sibling 567 installation rules do not own the environment side, sibling 262 narrow-edge battery guide owns the SLK-1104 family specifically. The standing rule across the cluster is documentation per SKU, dated, signed. That rule, applied across the five pillars, is the smart-lock battery-requirement plan.

To run the worksheet on a specific shortlist, the buyer sends the per-SKU confirmation table from Pillar 5 to the supplier with the dated product page or written supplier answer required on every row. The supplier signs row 17; the buyer signs row 18; the project dossier holds the signed worksheet; the per-door program runs; the audit reads the chain.

For per-SKU confirmation against your shortlisted SKU, request the dated product page cell sheet at Request a quote. For per-sample battery-requirement discipline before bulk ordering, start at Order samples. For the umbrella engineering/installation cluster, see Smart Lock Installation Requirements, Smart Lock Electrical Requirements, Smart Lock Network Requirements, and the narrow-edge product-specific lifecycle in SLK-1104 Battery Guide.

Kosár
A cookie-k engedélyezésével javítható a felhasználói élmény ezen a weboldalon. Cookie-szabályzat
Chat on WhatsApp