Smart Lock Electrical Requirements
A smart lock is, first, an electrical device that happens to live in a door. Battery vs wired, USB-C emergency-power behavior, indoor vs outdoor power behavior, and standby vs peak current are not feature checkboxes — they are stage gates that the installer, integrator, and procurement officer must clear before the door is signed off. This article walks the electrical-side requirements as a process with five stages: power-source decision, wiring architecture, standby and peak current accounting, backup and emergency-power rules, and indoor/outdoor deployment envelope. Every per-model number outside the one PDP-cited block is sent back to the product page; electrical specs are model-specific and the factory does not blanket-stamp them across the catalog.
The first sentence a buyer should be able to extract: electrical requirements for a smart lock are not a single specification — they are a five-stage process (power source → wiring → standby/peak current → backup power → deployment envelope), and each stage is decided per door, per model, on the product page, not at the catalog level.
Stage 0 — Framing the electrical question before the SKU is named
Before the procurement officer opens a catalog page, three questions frame every electrical decision that follows:
- Is the door expected to run on battery, on wired mains, or on a hybrid (mains with battery fallback)?
- Is the door indoor-conditioned, indoor-unconditioned, semi-outdoor, or fully outdoor?
- Is emergency access part of the operational promise (hotel guest locked out, tenant phone dead, fire-egress unlock) or only a mechanical-key fallback?
These three answers determine which electrical failure modes the lock must survive, which in turn determine the wiring plan, the battery chemistry, the standby budget, and the sealed-electronics envelope. Skipping Stage 0 leads to a common procurement error: the catalog page lists "USB-C emergency power" or "4 × AA battery" without saying for which SKU, at which door thickness, in which climate class. The factory's standing rule is that per-model electrical numbers must be confirmed on the product page — voltage, current, battery count, USB-C presence, and standby behavior are model-specific and are not ported across product lines.
Standing rule for the rest of this article: if a number below is not from the PDP-cited SLK-9936S block, it is an example, a question, or a routing back to the product page. Do not assume.
Stage 1 — Power source: battery, wired, or hybrid
The power-source decision is a stage gate because it changes every downstream artifact (conduit plan, battery runbook, emergency-power plan, and the spare-parts kit the integrator carries on the truck).
Stage 1 entry criteria
- The door class is known (hotel guestroom, apartment entry, office single-tenant, retail back-of-house, outdoor gate, glass door, cabinet).
- The expected daily unlock volume is known (a 200-room hotel with RFID cards cycles more than a 4-room boutique with PIN-only).
- The maintenance window is known (a hotel corridor that cannot be taken offline at any hour behaves differently from a factory back-of-house that can be powered down for an hour).
- The aesthetic constraint is known (a glass door cannot accept a wired conduit without a visible channel; a mortised lock on a heritage wood door can).
Stage 1 exit criteria
- A single decision is recorded on the door schedule: battery, wired, or hybrid.
- The chosen power architecture is named against a SKU family, not against a category. "Hotel lock on battery" is not a decision — "SLK-9936S-class hotel lock on 4 × AA" is a decision; even then, every figure below that headline must be confirmed on the product page for the specific model being purchased.
- The wired decision has a cable spec (conductor gauge, jacket rating, run length) named; the battery decision has a chemistry and a replacement interval named.
The three power-source architectures
| Architecture | When it fits | What it demands of the building | What it does not do |
|---|---|---|---|
| Battery only | Hotel guestrooms, residential entry doors, retrofit projects where no conduit exists, glass doors, cabinet locks | Annual or quarterly battery swap interval; spare-battery kit at the front desk or service cart; published low-battery alert threshold | Does not eliminate the need for an emergency-access plan (a flat battery in a guestroom at 02:00 is the same operational failure regardless of how well the maintenance is scheduled) |
| Wired only | New-build hotels with conduit in the door frame, commercial offices with above-ceiling access, gates with a dedicated power circuit, projects where battery swap labor is unacceptable | Conduit plan in the door frame; cable rated for the door's swing cycle; surge protection on the supply; a service loop at the hinge; a documented disconnect for maintenance | Does not remove the need for a battery — most wired smart locks still carry an internal cell for ride-through during a power blip; confirm the ride-through behavior on the product page |
| Hybrid (mains + internal cell) | Hotels, hospitals, schools where downtime is unacceptable and the building has a managed UPS on the corridor | Conduit plan plus battery runbook; UPS upstream if the corridor is on a generator-backed circuit; clear documentation of which behavior is from the wired feed and which from the cell | Does not substitute for a generator; a hybrid lock without upstream UPS will fail the moment the corridor circuit fails |
Decision rules for Stage 1
- If the door is a hotel guestroom and the property has a corridor UPS, choose hybrid.
- If the door is a hotel guestroom in a retrofit building without conduit in the frame, choose battery and budget the swap interval into the housekeeping SOP.
- If the door is an outdoor gate, choose wired unless the gate has no power run available — in which case battery is acceptable only if the gate is reachable for a swap in under 15 minutes.
- If the door is glass, choose battery; running a wired conduit on a glass door is a visible channel that almost no specifier accepts.
- If the door is a cabinet or interior safe-style enclosure, choose battery and accept that the swap interval is owner-driven, not staff-driven.
Those rules collapse into one gate the buyer walks per door — name the door class first, then let the class answer the architecture:
flowchart TD
A["Door class named on the schedule"] --> B{"Hotel guestroom with corridor UPS?"}
B -- "yes" --> C["Hybrid — wired feed plus internal cell ride-through"]
B -- "no" --> D{"Hotel guestroom in a retrofit without in-frame conduit?"}
D -- "yes" --> E["Battery — swap interval budgeted into the housekeeping SOP"]
D -- "no" --> F{"Outdoor gate?"}
F -- "yes" --> G["Wired — unless no power run is available"]
F -- "no" --> H{"Glass door?"}
H -- "yes" --> I["Battery — a wired conduit on glass is a visible channel"]
H -- "no" --> J["Cabinet or interior enclosure — battery, owner-driven swap"]
C --> K["Record the decision per door, per model, on the product page"]
E --> K
G --> K
I --> K
J --> K
A standing warning: a buyer who writes "battery-powered smart lock" once on the door schedule and re-uses that line across 12 model numbers has not made 12 decisions — they have made one decision and 11 assumptions. Stage 1 must be repeated per door, per model, on the product page.
Stage 2 — Wiring architecture: conduit, conductor, and the door-frame problem
Wiring a smart lock is not the same as wiring a light switch. The cable crosses a hinge, lives inside a door frame or a door slab, and must survive tens of thousands of swing cycles. The wiring architecture is therefore a stage gate, not a detail.
Stage 2 entry criteria
- The Stage 1 power decision is recorded as wired or hybrid.
- The door-frame material is known (aluminum, wood, steel, hollow metal, glass).
- The door swing direction and hinge type are known (this determines whether the cable runs through the hinge knuckle, through a transfer hinge, or through a door-loop).
- The supply voltage at the corridor junction box is known and stable.
Stage 2 exit criteria
- A wiring diagram is on file naming conductor gauge, jacket rating, transfer method, and the disconnect point.
- The cable is documented as in-conduit, in-frame, or in-slab, with the bend radius respected.
- The maintenance access point is named (where the integrator opens the wall to replace the cable).
The wiring-architecture matrix
| Building condition | Recommended transfer method | Conductor spec to check against the model specification | Failure mode if mis-specified |
|---|---|---|---|
| Hollow metal frame, new-build | In-frame conduit with a transfer hinge or a door-loop | Gauge, jacket rating, max run length — check the model’s published specification | Pinched cable at the hinge, intermittent power, warranty-voiding |
| Wood frame, retrofit | Surface-mount door-loop with a cable channel | Jacket rating for the corridor environment; UV if sun-exposed | Visible cable damaged by cleaning, conductor fatigue at the loop bend |
| Aluminum frame, retrofit | Surface-mount armored cable or wireless (battery) decision | Same as wood, plus a check that the aluminum frame does not require a thermal break that conflicts with the channel | Galvanic corrosion at the frame contact, cable jacket embrittlement |
| Glass door | Battery decision almost always; if wired, consult factory | Check the model’s published specification — most glass-door locks are not designed for wired supply | Visible channel through the glass, gasket failure |
| Outdoor gate | Buried conduit in a duct bank, surge protection at the source | Gauge, jacket rating (UV-resistant, water-resistant), maximum run length | Water ingress into the junction box, surge-induced lock reboot loops |
Three wiring decisions that bite the integrator on day one
- Transfer method before conductor spec. Choosing a transfer hinge first and then trying to fit a cable through it is a common ordering error. The transfer hinge must be specified to accept the cable diameter; this is a per-SKU value, and the right answer is verified in writing on the product page.
- Service loop at the hinge. A cable that runs tight across the hinge knuckle will fatigue in months, not years. The service loop is sized by the hinge geometry and the swing angle; a 90° hinge needs less loop than a 180° pivot hinge.
- Disconnect for maintenance. A smart lock that cannot be electrically isolated without opening the wall is a service-call problem waiting to happen. The disconnect point is a junction box at the corridor side of the frame, not a wire nut inside the wall cavity.
Wiring architecture decisions are model-specific. Voltage, current, cable diameter, transfer method, and disconnect topology are all confirmed on the product page for the SKU being purchased.
Stage 3 — Standby and peak current: the budget most buyers skip
Standby current is the load the lock draws between unlocks. Peak current is the load the lock draws during an unlock event (motor spin, RFID read, BLE/Wi-Fi transmit burst). The ratio between the two determines how long the battery lasts, how thick the wired cable must be, and whether the corridor UPS will hold the door through a 30-minute outage. Most procurement documents skip this stage — and that is where the surprises come from. The current-draw side of that budget is walked line by line in the sibling piece Smart Lock Power Consumption.
The PDP-cited reference figure: SLK-9936S hotel lock
The SLK-9936S is the first-party anchor for hotel-lock electrical planning. Its published electrical block is:
Power: 4 × AA · battery operating cycles >15,000 · audit/event records up to 1,000
This block is the documentation-granularity ruler for the rest of the catalog: it tells the buyer what the factory publishes for this SKU and what the buyer should expect for any other SKU at the same documentation tier. It is not a catalog-wide claim. The SLK-9936S's 4×AA chemistry, its >15,000-cycle figure, and its peak/standby behavior apply to the SLK-9936S only; they do not port to the SLK-9936G, the SLK-9905A, the SLK-9951TH, the SLK-9962S, the SLK-G200, the SLK-8831, the SLK-1104 class, the SLK-3108, the cylindrical-tuya model, the 3D-face model, or any of the cabinet, glass, face, camera/4G, or RFTC/RF hotel card-and-code models. Each of those is its own electrical spec, and the right answer is verified in writing on the product page.
Standby vs peak — the working numbers the buyer needs
| Parameter | What it is | Why it matters | Where the answer lives |
|---|---|---|---|
| Standby current (μA–mA range) | The draw between unlock events | Sets the floor for battery life on a battery lock and the steady load on a wired supply | — |
| Peak current during unlock (mA–A range) | The draw during motor spin, RFID read, BLE/Wi-Fi burst | Sets the wire gauge and the UPS headroom for wired locks; sets the worst-case voltage drop across a long cable run | — |
| Peak duration (ms–s range) | How long the peak lasts | A short peak on a small internal cell is acceptable; a long peak on a small cell is a brown-out risk | — |
| Battery operating cycles | Number of unlock events per battery set | The single most-cited battery figure on a smart lock product page — and the most-misread | The SLK-9936S publishes >15,000 cycles for that model only; every other SKU is confirmed on the product page |
| Audit/event log retention | How many events the lock stores between sync | Sets the maintenance cadence for log pull on standalone locks | The SLK-9936S publishes up to 1,000 records for that model only; every other SKU is confirmed on the product page |
| Cold-weather derating | Capacity loss on alkaline cells below ~0 °C; lithium behavior at –20 °C | An outdoor gate in a cold climate cannot use the same chemistry as a hotel guestroom | Check the model’s published specification per SKU; alkaline vs lithium is a per-door decision |
Cells marked — have no documented value in this article’s sources; obtain the figure from the supplier’s written specification.
How to use the table above
Treat it as a checklist of questions, not a checklist of answers. Every row is a "what is the figure for the SKU I am buying on the door I am wiring?" question, and every answer is on the product page. The procurement officer who reads "15,000 cycles" once and writes it across the door schedule has made one assumption per SKU and will discover those assumptions in the first quarter of operation.
A worked example for a hotel guestroom
Consider a 200-room hotel corridor, RFID cards as the primary credential, mechanical key as the emergency fallback, audit logs pulled weekly. The electrical plan for one guestroom door:
- Power source (Stage 1): battery, because the corridor was built without in-frame conduit. Check the model’s published specification whether the SKU is designed for battery-only or whether it requires a wired feed even on retrofit doors.
- Wiring (Stage 2): none required at the door; the battery compartment is the only electrical interface. The corridor has no junction box at the frame.
- Standby/peak (Stage 3): the buyer names the SKU and asks the factory for the standby figure, the peak figure, and the peak duration. These three numbers, multiplied by the expected daily unlock count, set the battery replacement interval. Check the model’s published specification.
- Battery chemistry (Stage 4 below): the buyer chooses alkaline or lithium for the SKU's compartment; cold-weather corridor storage may force lithium even in a temperate climate.
- Deployment envelope (Stage 5 below): the door is indoor-conditioned, but the corridor is unconditioned in winter; condensation on the inside of the door is possible. Sealed-electronics class is asked of the SKU, not of the category.
This is what a Stage 0-to-3 plan looks like for one door. The same plan for 200 doors, with one number per row confirmed per SKU on the product page, is what the procurement officer actually needs to ship to the integrator.
Stage 4 — Backup power: USB-C, mechanical key, and the honest framing of "emergency power"
The phrase "USB-C emergency power" appears on consumer-grade smart lock marketing pages and has migrated into B2B conversations. It deserves an honest framing.
What USB-C emergency power is — and is not
USB-C emergency power, when present on a B2B smart lock, is a temporary power input used to wake the lock's electronics long enough to read a credential and unlock the door when the primary cell is flat. It is not a charging port for the primary cells; it is not a permanent power input; it is a 5 V feed at the door-side contacts, applied for tens of seconds, intended to let a stranded guest or tenant enter with a power bank.
A buyer who reads "USB-C emergency power" on a category page and writes it across the RFQ has made an assumption the factory does not support at the catalog level. USB-C emergency power presence is a per-model feature; check the model’s published specification. Models that ship with USB-C, models that ship with a 9 V battery clip, and models that ship with neither are all in the catalog; the buyer names the SKU and asks the factory.
The four backup-power architectures the buyer should know
| Backup architecture | What it does | What it does not do | Where the answer lives |
|---|---|---|---|
| USB-C emergency power | Wakes the lock's electronics for one unlock event when the primary cell is flat | Does not recharge the primary cells; does not substitute for the primary cell on subsequent events | — |
| 9 V battery clip / contact pads | Same intent as USB-C, with a different physical interface | Same limitations | — |
| Mechanical key override | Opens the door without any electronics, on a 5-pin cylinder or equivalent | Does not log the event; does not interface with the management software | PDP-cited for the SLK-9936S as "mechanical emergency access"; presence on every other SKU is confirmed on the product page |
| None (electronics only) | Some sealed-design locks omit the mechanical override | A flat cell locks the door against the credentialed user, not just against the credential | — |
Honest framing of the "USB-C" line in an RFQ
If the RFQ says "smart lock with USB-C emergency power" without naming a SKU, the factory will ask which model. The honest, defensible RFQ reads:
"For the shortlisted SKU family, confirm whether the lock supports a temporary 5 V USB-C emergency-power input to wake the electronics for one unlock event when the primary cell is flat. Check the model’s published specification. If the SKU does not support USB-C, name the alternative emergency-power architecture (9 V clip, mechanical key override, or neither)."
This is the form the factory can answer; the categorical form it cannot. The mechanical-key override on the SLK-9936S is published; the USB-C behavior on the SLK-9936S is not in the PDP-cited block and must be confirmed on the product page.
Backup-power decision rules
- Hotel guestroom: mechanical key override is non-negotiable for the property insurance policy. USB-C or 9 V clip is a convenience layer above that. Check the model’s published specification which emergency-power layers the shortlisted SKU ships with.
- Apartment entry: mechanical key override plus USB-C or 9 V clip is the typical pair; some markets require the mechanical key cylinder to be a removable-core design for property management.
- Office single-tenant: mechanical key override is often omitted in favor of a hardwired supply on a UPS; check the model’s published specification.
- Outdoor gate: mechanical key override and a wired supply on a generator-backed circuit; USB-C is not a substitute for a generator.
- Cabinet / interior enclosure: mechanical key or PIN-only fallback; USB-C is rarely relevant.
Stage 5 — Deployment envelope: indoor, indoor-unconditioned, semi-outdoor, outdoor
The deployment envelope is the climate and exposure class around the door. It determines the sealed-electronics class, the battery chemistry, the cable jacket rating, and the warranty conversation (warranty terms are model-specific and are not asserted here — check the model’s published specification).
The four envelope classes
| Envelope | Conditions | Typical door classes | Electrical consequence |
|---|---|---|---|
| Indoor-conditioned | 15–25 °C, 30–60% RH, no direct sun, no direct water | Hotel guestrooms, interior office doors, residential interior doors | Standard battery or wired supply; alkaline acceptable; standard jacket rating |
| Indoor-unconditioned | 0–35 °C, 20–80% RH, possible condensation, no direct water | Corridor doors in unconditioned hotel wings, basement entries, storage rooms | Lithium cells in cold months; sealed-electronics class asked per SKU; check the model’s published specification |
| Semi-outdoor | Covered entry, sun on the door, splash possible, no submersion | Apartment entry vestibules, retail back-of-house entries, covered gates | UV-resistant jacket; sealed-electronics class asked per SKU; battery chemistry verified for the temperature swing; check the model’s published specification |
| Outdoor | Direct sun, direct rain, possible submersion, dust, biological exposure | Garden gates, perimeter gates, exterior doors of unconditioned buildings | Wired supply on a generator-backed circuit where possible; lithium cells where battery-only; sealed-electronics class mandatory per SKU; check the model’s published specification |
Sealed-electronics class — what to ask
"Sealed-electronics class" is not a single number. It is a per-SKU claim covering:
- Water ingress at the rating the factory publishes (often expressed against a published standard, but the specific standard and the specific test conditions are model-specific — check the model’s published specification).
- Dust ingress at the same rating tier.
- UV resistance of the housing and the cable jacket (relevant for semi-outdoor and outdoor).
- Operating temperature range, including cold-weather derating for the battery chemistry.
- Condensation behavior — a lock rated for splash is not automatically rated for condensation.
A buyer who writes "IP65" once on the door schedule has made one assumption across every door. The right form is per door, per SKU, on the product page.
Indoor-vs-UV deployment — what changes for the battery
A door in direct sun through a glass vestibule is a semi-outdoor door, not an indoor door. The lock body sits at 50–60 °C in summer sun and at 5 °C in winter morning. Alkaline cells lose capacity at both ends of that range; lithium cells hold capacity better but at higher cost and with their own temperature envelope. The electrical consequence is:
- Alkaline: acceptable only for indoor-conditioned doors with a known battery-swap cadence. Not acceptable for outdoor gates, semi-outdoor entries, or any door whose body temperature is unknown.
- Lithium: acceptable for indoor-conditioned, indoor-unconditioned, semi-outdoor, and outdoor doors, subject to the SKU's own temperature envelope. Check the model’s published specification.
- Rechargeable cell (NiMH, Li-ion): appears on some models; charging behavior in a high-heat door is a per-SKU question. Check the model’s published specification.
A door's UV exposure is also a housing question. The buyer asks the factory whether the housing and the cable jacket are UV-rated for the project's latitude and orientation; the answer is per SKU.
Stage 6 — Per-model confirmation matrix (catalog honesty)
The honest catalog position is that electrical requirements are model-specific. The matrix below names the SKU families and the electrical question to ask on each product page. Every cell is a routing back to the product page; the matrix is the buyer's checklist, not the factory's blanket claim.
| SKU family | Power architecture to confirm | Battery spec to confirm |
|---|---|---|
| SLK-9936S (hotel smart door lock) | Battery or wired — check the model’s published specification | 4 × AA, >15,000 cycles (PDP-cited for this model only) |
| SLK-9936G | Battery or wired — check the model’s published specification | — |
| SLK-9905A (hidden-reader hotel lock) | Battery or wired — check the model’s published specification | Door thickness ~38–100 mm is published; battery spec is per SKU — check the model’s published specification |
| SLK-9951TH (hotel electronic lock) | Battery or wired — check the model’s published specification | — |
| SLK-9962S (hotel electronic lock) | Battery or wired — check the model’s published specification | — |
| SLK-G200 (glass door smart lock) | Battery only typical for glass; check the model’s published specification | — |
| SLK-8831 (5-in-1 fingerprint/password/card/key/app) | Battery or wired — check the model’s published specification | — |
| SLK-1104 class (narrow-edge 4-in-1 with waterproof door lock) | Battery or wired — check the model’s published specification; "waterproof" claim is per SKU | — |
| SLK-3108 (password smart door lock) | Battery or wired — check the model’s published specification | — |
| Cylindrical Tuya round code lock | Battery typical — check the model’s published specification | — |
| 3D face-recognition / intercom / smart lock | Wired typical — check the model’s published specification | Check the model’s published specification (face modules are higher draw) |
| Cabinet locks (6 models in catalog) | Battery only — check the model’s published specification | Check the model’s published specification (smaller cell typical) |
| Outdoor/D-series (D11, D12, D15, ODS, DQ) | Wired or battery — check the model’s published specification | — |
| Glass — B09 double-opening face recognition | Battery typical — check the model’s published specification | — |
| Face — 9L5-R, Q7, Future 1 | Wired typical — check the model’s published specification | — |
| Camera/cat-eye — 516 | Wired typical — check the model’s published specification | — |
| 4G model | Wired or hybrid — check the model’s published specification | — |
| RFTC/RF hotel card & code locks (118, 118E, 228, 230, 232, 238, 239, 253, 305, 306, 308, 309, 502, 620, 621, 911, 002, 019, 022, 2020, 760; stainless options 019/022/309) | Battery or wired — check the model’s published specification | — |
The SLK-9936S row in this matrix is the only row where the battery spec is published in the PDP-cited block. Every other row is a question to ask on the product page. The buyer who treats the SLK-9936S numbers as a catalog-wide claim has made the most common procurement error in this category.
Stage 7 — The decision matrix: which electrical architecture wins per door class
| Door class | Default architecture | Default battery | Default backup power | Default envelope class |
|---|---|---|---|---|
| Hotel guestroom | Battery (retrofit) or hybrid (new-build) | — | Mechanical key + USB-C or 9 V clip — check the model’s published specification | Indoor-conditioned or indoor-unconditioned |
| Serviced apartment unit door | Battery | — | Mechanical key + USB-C or 9 V clip — check the model’s published specification | Indoor-conditioned |
| Apartment building entry | Wired with battery fallback | — | Mechanical key — check the model’s published specification | Indoor-unconditioned or semi-outdoor |
| Office single-tenant door | Wired on UPS | n/a (wired) | Mechanical key — check the model’s published specification | Indoor-conditioned |
| Office multi-tenant common door | Wired on UPS with battery fallback | — | Mechanical key — check the model’s published specification | Indoor-conditioned |
| Retail back-of-house | Wired or battery | — | Mechanical key — check the model’s published specification | Indoor-unconditioned or semi-outdoor |
| Outdoor gate (perimeter) | Wired on generator-backed circuit; battery acceptable if no conduit run is feasible | Lithium if battery — check the model’s published specification | Mechanical key — check the model’s published specification | Outdoor |
| Glass door | Battery only typical | — | Mechanical key — check the model’s published specification | Indoor-conditioned or indoor-unconditioned |
| Cabinet / interior enclosure | Battery only | — | Mechanical key or PIN — check the model’s published specification | Indoor-conditioned |
The matrix is the buyer's per-door decision, not a catalog-wide claim.
Stage 8 — Process scorecard: the 12 items the RFQ must clear
A buyer-side scorecard for whether the RFQ has done the electrical work before the supplier's quote arrives. Severity is CRITICAL / RECOMMENDED / OPTIONAL.
| # | Item | Severity | Owner | Evidence |
|---|---|---|---|---|
| 1 | Every door on the schedule has a Stage 1 power-source decision (battery / wired / hybrid) | CRITICAL | Procurement | Door schedule row, signed |
| 2 | Every wired door has a Stage 2 wiring architecture (conductor, transfer method, disconnect) | CRITICAL | Integrator | Wiring diagram on file |
| 3 | Every battery door has a battery chemistry named (alkaline / lithium / NiMH / Li-ion) | CRITICAL | Procurement | Door schedule row |
| 4 | Every SKU has standby and peak current figures confirmed on the product page | CRITICAL | Procurement | Product-page reference per SKU |
| 5 | Every battery door has a battery replacement interval named | CRITICAL | Operations | Runbook |
| 6 | Every door has a backup-power architecture named (mechanical key, USB-C, 9 V clip, or none) | CRITICAL | Procurement + property insurer | Door schedule row |
| 7 | Every outdoor and semi-outdoor door has a sealed-electronics class confirmed on the product page | CRITICAL | Procurement | Product-page reference per SKU |
| 8 | Every wired door has a UPS or generator upstream decision recorded | RECOMMENDED | Engineering | Electrical single-line |
| 9 | Every hotel guestroom door has a corridor UPS decision recorded | RECOMMENDED | Engineering | Electrical single-line |
| 10 | Every door has a deployment-envelope class assigned (indoor-conditioned / indoor-unconditioned / semi-outdoor / outdoor) | RECOMMENDED | Procurement | Door schedule row |
| 11 | The integrator has a per-SKU service-loop plan at the hinge | RECOMMENDED | Integrator | Wiring diagram |
| 12 | The operator has a battery-swap SOP keyed to the SKU's chemistry and interval | OPTIONAL | Operations | Runbook |
A row marked CRITICAL with no evidence is a Stage gate that has not been cleared; the door is not ready to order.
Stage 9 — Illustrative scenario: a 240-door mixed-use property
Consider a 240-door mixed-use property: 120 hotel guestrooms, 60 serviced apartment units, 40 office multi-tenant common doors, and 20 retail back-of-house doors. The property has corridor UPS on the hotel floors and the office floors; the serviced apartment floors and the retail back-of-house are on the building general supply without corridor UPS.
Hotel guestrooms (120 doors)
The integrator pulls the SLK-9936S class. Stage 1: hybrid — corridor UPS feeds a wired supply, with the 4 × AA cells (PDP-cited for this model) as ride-through. Stage 2: in-frame conduit with a transfer hinge. Stage 3: standby and peak current are confirmed on the product page; the SLK-9936S publishes >15,000 cycles for that model only. Stage 4: mechanical key override plus USB-C emergency-power — check the model’s published specification whether this SKU ships with USB-C. Stage 5: indoor-conditioned envelope; sealed-electronics class is per SKU on the product page.
Serviced apartment units (60 doors)
Stage 1: battery — the corridor was not built with in-frame conduit. Stage 2: none required. Stage 3: standby and peak current confirmed per SKU on the product page; the SLK-9936S 4 × AA / >15,000 cycle block is not ported to whatever SKU the integrator selects for these doors. Stage 4: mechanical key override plus USB-C — check the model’s published specification. Stage 5: indoor-conditioned envelope; sealed-electronics class confirmed per SKU.
Office multi-tenant common doors (40 doors)
Stage 1: wired on corridor UPS with internal cell for ride-through. Stage 2: in-frame conduit with a transfer hinge; disconnect at the corridor junction box. Stage 3: standby and peak confirmed per SKU on the product page. Stage 4: mechanical key override; USB-C typically absent on this class — check the model’s published specification. Stage 5: indoor-conditioned envelope.
Retail back-of-house doors (20 doors)
Stage 1: battery — no conduit to the back-of-house. Stage 2: none required. Stage 3: standby and peak confirmed per SKU on the product page. Stage 4: mechanical key override; USB-C or 9 V clip — check the model’s published specification. Stage 5: indoor-unconditioned envelope; condensation possible in the loading-dock area; sealed-electronics class confirmed per SKU.
What the integrator carries to site
A service-truck kit keyed to the four door classes, with:
- The four SKU families and their product-page references.
- The per-SKU battery chemistry and replacement interval.
- The per-SKU mechanical key override confirmation.
- The per-SKU USB-C or 9 V clip emergency-power confirmation.
- A per-SKU service-loop length and transfer method.
- A per-door-stage-gate signed door schedule.
The kit is the visible evidence that Stage 0 through Stage 8 have been done. Without it, the integrator is making the electrical decisions on the door, and that is where the surprises live.
What "battery vs wired" actually decides
Battery vs wired is not a preference question. It is a stage gate with five downstream consequences:
- Conduit plan. Wired and hybrid require a conduit decision; battery does not.
- Battery runbook. Battery and hybrid require a swap SOP; wired-only usually does not.
- UPS upstream. Wired and hybrid should sit on a UPS or generator; battery-only does not.
- Emergency-power architecture. Every door needs a mechanical key or a USB-C/9 V clip or a hybrid of the two; the choice is per SKU on the product page.
- Maintenance access. Wired and hybrid need a disconnect point; battery needs a service-loop at the compartment cover.
A buyer who has done Stage 1 well has answers to all five; a buyer who has not has answers to none.
What "USB-C emergency power" actually means
USB-C emergency power, when present on a B2B smart lock, is a temporary 5 V feed at the door-side contacts, applied for tens of seconds, intended to wake the lock's electronics for one unlock event when the primary cell is flat. It is not a charger for the primary cells; it is not a permanent power input; it is not a guarantee on every SKU. Presence is per model, confirmed on the product page. The honest framing in an RFQ reads:
"For the shortlisted SKU family, confirm whether the lock supports a temporary 5 V USB-C emergency-power input to wake the electronics for one unlock event when the primary cell is flat. Check the model’s published specification. If the SKU does not support USB-C, name the alternative emergency-power architecture (9 V clip, mechanical key override, or neither)."
This is the form the factory can answer. The categorical form ("smart lock with USB-C emergency power") the factory cannot.
What "indoor vs UV deployment" actually changes
Indoor-conditioned and outdoor doors are different electrical problems, not different feature checkboxes. The differences the buyer must capture:
- Battery chemistry. Alkaline loses capacity outside 0–40 °C; lithium holds capacity over a wider range. A door in direct sun through a glass vestibule is semi-outdoor, not indoor-conditioned.
- Cable jacket rating. Indoor cable jackets embrittle under UV; outdoor-rated jackets are mandatory on semi-outdoor and outdoor doors. Check the model’s published specification.
- Sealed-electronics class. Splash and condensation are different ingress modes; a lock rated for splash is not automatically rated for sustained condensation. Check the model’s published specification.
- Cold-weather derating. A door at –10 °C in winter morning behaves differently from a door at 20 °C year-round; lithium cells help, but the SKU's own temperature envelope still applies. Check the model’s published specification.
- UV on the housing. Direct sun degrades plastics over years; the SKU's housing material and the project's latitude are jointly relevant. Check the model’s published specification.
A buyer who treats indoor and UV deployment as the same electrical problem has under-specified the project. The sealed-electronics class is per SKU, the chemistry is per SKU, the jacket rating is per SKU, and the cold-weather derating is per SKU.
What the RFQ must ask the factory — verbatim
A standing list of seven questions the RFQ must ask the factory before the supplier's quote is accepted. Each question has a single owner and a single evidence artifact.
- For the shortlisted SKU family, confirm the power architecture (battery, wired, or hybrid). State the voltage, the standby current, the peak current, and the peak duration. Check the model’s published specification.
- For the shortlisted SKU family, confirm the battery spec — chemistry, cell count, replacement interval, and the operating-cycle figure. The SLK-9936S publishes 4 × AA and >15,000 cycles for that model only; every other SKU is confirmed on the product page.
- For the shortlisted SKU family, confirm whether the lock supports a temporary 5 V USB-C emergency-power input to wake the electronics for one unlock event when the primary cell is flat. Check the model’s published specification.
- For the shortlisted SKU family, confirm the mechanical-key override presence and the cylinder spec (5-pin for the SLK-9936S is PDP-cited; every other SKU is confirmed on the product page).
- For the shortlisted SKU family, confirm the sealed-electronics class — water ingress standard and test conditions, dust ingress standard and test conditions, operating temperature range, UV resistance of the housing and jacket. Check the model’s published specification.
- For wired or hybrid shortlisted SKUs, confirm the recommended conductor gauge, jacket rating, transfer method (transfer hinge or door-loop), maximum run length, and the disconnect point. Check the model’s published specification.
- For outdoor or semi-outdoor shortlisted SKUs, confirm the cold-weather derating for the battery chemistry and the UV-resistance class for the housing. Check the model’s published specification.
A factory that answers all seven questions per SKU has done the electrical work; a factory that answers "see the catalog page" has not. The buyer takes the answers to the door schedule and pins them per door, per SKU.
Closing the loop on the electrical side
The electrical-side requirements for a smart lock are a process, not a feature list. Stage 0 frames the question before the SKU is named; Stage 1 chooses battery, wired, or hybrid; Stage 2 lays the wiring architecture; Stage 3 budgets standby and peak current; Stage 4 names the backup-power architecture; Stage 5 assigns the deployment envelope; Stage 6 confirms the per-model spec on the product page; Stage 7 maps the architecture to the door class; Stage 8 scores the RFQ; Stage 9 walks the mixed-use scenario.
The single rule that ties all nine stages together is the per-model confirmation discipline. Every electrical number outside the PDP-cited SLK-9936S block (4 × AA, >15,000 cycles for that model only) is sent back to the product page. The buyer who follows that rule ships a project whose electrical side holds up to the integrator's first service call; the buyer who does not ships a project whose electrical side is a list of assumptions waiting to fail.
For the door-side mechanical fit (door thickness, mortise pocket, backset, lever height), the sibling article Smart Lock Installation Requirements lays out the matching process. For the battery chemistry and replacement cadence, the sibling article Smart Lock Battery Requirements walks the runbook. For the connected-side electrical question (gateway power, PoE, network-side UPS), the sibling article Smart Lock Gateway Installation Requirements covers the upstream end. The electrical side of a smart lock is the gate the integrator walks through first; the door schedule, the BOQ, the wiring diagram, and the battery runbook all live downstream of it. Check the model’s published specification; ship per SKU; treat every door as its own stage gate.
For the project quote that names per-SKU electrical options against your door schedule, request a quote with the door schedule attached. For sample units that let the integrator bench-test the standby, peak, and USB-C behavior before the order is sized, order samples keyed to the shortlisted SKU families.

