Mechanical load is the load-bearing side of those three — load against displacement, load against geometry, load against the way a door falls onto its frame.

Diterbitkan Pada: Nov 11, 2026

Smart Lock Mechanical Load Testing

Smart Lock Mechanical Load Testing

Mechanical load testing is the buyer-side discipline of proving that a smart lock keeps its mechanical geometry, mechanical integrity, and mechanical control when force is applied to it from any plausible direction. In B2B procurement the question is not "does the lock survive a single handshake" — it is "does it survive a slammed door, a shoulder hit, a leaning tenant, a curious child, a frustrated guest, an installer with a wrench in the wrong direction, and a building crew that uses the door as a wheelbarrow rest." Force applied to a lock is a vector problem: the same lock can hold beautifully against an axial pull and fail catastrophically under a torsional or lateral load it was never designed to resist. This article is an annotated datasheet of the mechanical-load test matrix that a buyer's QA team should be able to read row by row, line by line, and use as the worksheet behind any pre-RFQ load audit, pilot-floor load check, or goods-received mechanical acceptance.

The per-model rule that governs every cell

One discipline holds the entire worksheet together: load ratings are per-model numbers. A kg, newton, or newton-metre value quoted for one lock does not port across the catalog. To read the rating that applies to the lock you are buying, check the model’s published specification of the verified PDP slug. This datasheet does not assert any specific kg/N/Nm figure on any model row; every cell that needs a number is left blank with the to verify in writing marker. Treat any supplier-quoted load figure you cannot point to on the verified product page as undefined until the supplier puts it in writing inside the contract annex.

Two siblings carry the rest of the testing thread: Smart Lock Security Architecture maps the security side, Smart Lock Durability Testing carries the broader cycle/environment/user-weight checklist, and Smart Lock Motor Life Testing drills on the motor-and-gearbox axis. Mechanical load is the load-bearing side of those three — load against displacement, load against geometry, load against the way a door falls onto its frame.

What a mechanical-load test actually measures

A mechanical-load test, at its core, records two numbers: the force applied (in newtons, kilograms of pull, or newton-metres of torque) and the displacement or deformation observed at the load point (in millimetres of deflection, degrees of rotation, or permanent set). Three load modes dominate the matrix:

Static load — a slow, sustained force applied through a fixture (a calibrated pull gauge, a push ram, a torque wrench). Static load is the "lean on the handle" test, the "shove the bolt" test, the "twist the cylinder" test. Static load is the cheapest test to run, the easiest to witness, and the most reproducible across labs. Static-load results are what most supplier datasheets refer to when they quote a kg or N figure without specifying direction.

Dynamic load — a sudden force delivered as an impact or a slam. Dynamic load is the "kid on a scooter hits the door" test, the "housekeeping cart bumps the panel" test, the "delivery person shoulder-checks the door" test. Dynamic load is the most destructive single shot in the matrix and the one suppliers most often skip. A lock rated to a static-axial-pull number and never impact-tested is a lock whose first impact is its first surprise.

Cycling-under-load — the same load applied repeatedly to record degradation. A handle pulled to X newtons ten thousand times is a different mechanical question from a handle pulled to X newtons once. The 533 sibling owns cycle counts as a separate axis; this article treats cycling-under-load as the seam where static load and durability meet.

The matrix below layers two grids: rows = test names, columns = load direction. Where the seam crosses, the cell records what the buyer should demand to see and what to refuse unless the supplier proves it.

The load-direction vocabulary used in this article

Mechanical-load conversations get confused when buyer and supplier use the same word to mean different vectors. Before the matrix is read aloud, the six load directions must be agreed on.

Axial pull (also: "outward", "handle pull") — force perpendicular to the door face, directed away from the room. Applied at the handle, the lever, the knob, the credential-reader pull-tab, or the emergency-cover pull edge.

Axial push (also: "inward", "handle push") — force perpendicular to the door face, directed into the room. Applied at the handle after a latch has been defeated, or at the panel surface (e.g. a leaning shoulder).

Lateral (also: "sideways", "parallel") — force in the plane of the door face, perpendicular to the handle's axis of rotation. This is the "twist the lever sideways" load.

Torsional (also: "torque", "rotation") — moment around the handle's axis of rotation. Applied as turning force at the lever or as torque at the keyed cylinder.

Shear (also: "bolt shear", "latch shear") — force parallel to the door face along the axis of the bolt or latch, in the direction the bolt is pushed into or pulled out of the strike. This is the load that breaks bolt cross-sections and is the load a forced-entry attacker specifically seeks.

Impact (also: "perpendicular impact", "shock") — a sudden perpendicular force to any panel surface — the reader window, the keypad, the fingerprint platen, the faceplate. Impact is the directional cousin of axial push but delivered in milliseconds rather than seconds.

The matrix below uses these six directions as its column headers. Every test row that follows maps to one or more columns; cells without a recorded direction mean that direction is not the controlling failure mode for that test.

Annotated mechanical-load test matrix (per-test × per-load-direction)

The table below is the spine of this datasheet. Each row is a buyer-defined test. Each cell under a load-direction column answers three questions: what to demand the supplier evidence, what is a bluff, and what is undefined unless the supplier puts it in writing (to verify in writing — check the product page). Where the cell is empty for a given direction, that direction is not a primary failure mode for that test.

The first eleven rows are physical-component tests; the twelfth row is the integrated-door test; the thirteenth row is the seal/window test. Cross-references to product pages and to the 533 (durability) and 542 (motor life) siblings appear in the notes column.

#Test nameAxial pull (handle)Axial push (panel/handle)Lateral (handle)Torsional (handle/cylinder)Shear (bolt/latch)Impact (reader/keypad)
1Handle static loadcheck the model’s published specification (to verify in writing — check the product page); demand a fixture diagram; refuse any rating without direction specifiedcheck the model’s published specification (to verify in writing — check the product page); push direction is usually less than pullcheck the model’s published specification (to verify in writing — check the product page); sideways load is the one most often skippedsee row 2 (torsion)n/a — not the controlling modeN/A
2Handle torsion (torque to failure)N/AN/AN/Acheck the model’s published specification (to verify in writing — check the product page); demand the lever length used as moment armN/AN/A
3Lever free-rotation / free-handling———n/a — covered by row 2N/AN/A
4Cylinder torque (key/emergency)N/AN/AN/Acheck the model’s published specification (to verify in writing — check the product page); ask whether torque rating is to break or to functioncheck the model’s published specification (to verify in writing — check the product page); cylinder and bolt move as a system, not aloneN/A
5Deadbolt/bolt thrust (axial)——N/AN/Acheck the model’s published specification (to verify in writing — check the product page) — a bolt's shear rating is rarely quoted; demand itN/A
6Latch bolt push-back (card/shim resistance)N/AN/AN/AN/Acheck the model’s published specification (to verify in writing — check the product page); this is the lockpicking-adjacent test and is usually a different number than row 5N/A
7Reader/keypad window impactN/AN/AN/AN/AN/Acheck the model’s published specification (to verify in writing — check the product page); demand impact energy in joules and drop height in mm
8Fingerprint-platen pressureN/Acheck the model’s published specification (to verify in writing — check the product page); a thumb-press is not a fair test of platen resistanceN/AN/AN/A—
9Escutcheon pull-off (fastener retention)check the model’s published specification (to verify in writing — check the product page); this is the most-suppressed test in the matrix———N/AN/A
10Battery-cover retentioncheck the model’s published specification (to verify in writing — check the product page); a pry-off battery cover breaks the audit trail tooN/AN/AN/AN/AN/A
11Strike-plate / keeper pull-outN/AN/AN/AN/Acheck the model’s published specification (to verify in writing — check the product page); demand the substrate the rating was measured againstN/A
12Integrated door sag (after install)N/AN/AN/AN/Acheck the model’s published specification (to verify in writing — check the product page) — sag redirects shear into the bolt path over monthsN/A
13Environmental seal integrity (after load)N/AN/AN/AN/AN/Acheck the model’s published specification (to verify in writing — check the product page); seal ratings are normally expressed separately (see 538)

How to read the cells without slipping into assumption:

Cells marked check the model’s published specification (to verify in writing — check the product page) — the direction is a meaningful failure mode for that test, but this datasheet does not assert a numeric rating. The buyer is required to read the verified product page and to demand a written direction-quoted rating from the supplier before treating any number as binding.

Cells marked n/a — not the controlling mode — that load direction is not the one that determines whether the test passes. (Example: torsional load on the deadbolt's shear path is the wrong question; the right question is shear.)

Cells marked with specific sub-clauses ("demand a fixture diagram", "refuse any rating without direction specified") — those are bluff flags. A supplier that quotes "X newtons static load" without naming the direction is bluffing; you cannot compare two such quotes across catalogs.

Reading the matrix as a buyer-side worksheet

Used as a worksheet, every row becomes a check the buyer's QA team asks the supplier to run on the bench sample, on the retained sample, or on the production-lot sample. The worksheet behavior is:

  1. Run the row.
  2. Record the force, displacement, and observation.
  3. Compare the result against the per-model rating from the verified product page.
  4. Stamp the sign-off cell.
  5. File the worksheet as load-evidence.

Pass requires a number on the worksheet, a stamp in the sign-off, and a rating on the verified product page that the number can be compared against.

What each direction pulls out of the lock (annotated)

The annotations below dissect the matrix row by row, name the failure mode each direction triggers, and put a flag against the most common supplier bluff on that direction. Treat this section as the "what-this-line-means" column of an annotated datasheet.

Row 1: Handle static load — axial pull, axial push, lateral

A door handle sees three slow loads. Axial pull is the leaned-back guest who yanks the handle toward themselves before the latch clears; axial push is the leaned-in tenant who shoves the handle away; lateral is the laundry-basket hook catching the lever and twisting it sideways. The fixture that simulates all three is a calibrated pull-push gauge mounted to the lever's geometric center with a strap or socket adapter. The supplier's evidence should include the gauge model, the lever engagement, the loading rate (mm/min), and the failure criterion (permanent deformation, function loss, or fracture).

Bluff: a supplier that quotes "static load N newtons" with no direction. A handle can carry N newtons axially and fail at N/4 laterally. Without the direction, the figure is uninterpretable. Demand three separate ratings — pull, push, lateral — and refuse to fold them into a single number.

Row 2: Handle torsion — torsional

Torsion at the lever is the test that catches free-handle and clutched-handle designs in a corner. The fixture is a torque wrench applied at the lever's moment arm (the distance from the spindle axis to the lever tip). For a clutched or free-rotating lever, the rating is to the clutch slip, not to the spindle. For a fixed lever, the rating is to the spindle, the set screw, or the lever itself.

Bluff: a rating published as "lever torque" with no mention of the lever model. A 130 mm lever and a 95 mm lever produce very different moment arms; the rating is a moment, not a force. Demand the lever length and the rating in N·m, not in N.

Row 3: Lever free-rotation / free-handling — handled in row 1/2

If a model uses a free-rotation or clutched-handle design (a common feature on hotel locks to prevent forced-rotation attacks), the test fixture engages the lever, applies a moment, and confirms that the clutch slips before the spindle transmits torque. This row is functionally a sub-case of rows 1 and 2; it exists to remind the buyer that on a clutched model, the torsional rating is to slip, not to spindle fracture. Treating it as a spindle-torque number is a misreading.

Bluff: a supplier that quotes "torque N·m" without specifying whether the lever is fixed or clutched. The two ratings can differ by an order of magnitude.

Row 4: Cylinder torque — torsional, shear

The cylinder is the keyed override — the mechanical emergency access path that survives when the electronics fail. Torque at the cylinder is rated to break or to function, and the two numbers are not the same. A break rating of X N·m means the cylinder yields at X; a function rating of Y < X means the cylinder still turns the bolt at Y. A buyer-side worksheet should record both: the supplier states Y, and the buyer's audit confirms Y against a torque-wrench sweep.

The cylinder is also part of the shear path because turning the cylinder transmits torque to the bolt. Bolt-and-cylinder-as-system is how forced-entry testers think about it; treat them as one row, even though the question splits cleanly into torsional (cylinder) and shear (bolt) cells.

Bluff: a supplier that quotes "cylinder strength" as a single number. The cell above already separates torsional and shear; a number that compresses the two is a buyer's first clue that the supplier is quoting a brochure, not a test report.

Row 5: Deadbolt/bolt thrust — axial pull, axial push, shear

The bolt is the lock's primary mechanical anchor. Thrust ratings tell the buyer how hard an attacker can shove the bolt inward (axial push) or pull it outward (axial pull) before the bolt's mechanism yields. Shear ratings tell the buyer how hard the bolt can be forced sideways into or out of the strike before the bolt cross-section yields.

Bluff: a bolt thrust rating quoted without a corresponding shear rating. A bolt can take a huge axial push and snap in a single shear stroke. Demand both.

Row 6: Latch bolt push-back — shear

The latch is the angled-face bolt that springs into the strike and is meant to retract on a handle turn. "Latch push-back" is the lockpicking-adjacent test where a thin tool shoves the latch back into the door body from outside, bypassing the handle entirely. This is a shear question at the latch-face level, not an axial question.

Bluff: a latch push-back rating quoted without a substrate for the strike. A latch that holds against push-back in a hardwood strike may yield in a hollow metal strike. Demand the strike material the rating was measured against.

Row 7: Reader / keypad window impact — impact

The reader window is the surface buyers hit with keys, purses, elbows, and luggage corners. Impact is delivered with a calibrated drop-weight or a pendulum impactor, and the rating is given in joules of energy absorbed to a defined failure criterion (crack propagation, platen dislodgement, function loss). The 538 (Smart Lock Water Resistance) sibling owns the seal-side of this window; this article owns the impact side.

Bluff: a rating quoted in "drop height" without the drop mass. A 1 kg steel ball dropped 0.5 m and a 5 kg sandbag dropped 0.5 m are two different tests. Demand both numbers or, better, demand the joules.

Row 8: Fingerprint-platen pressure — axial push, impact

The fingerprint platen is the silicon or ceramic surface a finger presses against. Two distinct loads apply: the slow axial push (a thumb press — a functional load, not a destructive load) and the impact (a struck platen — a destructive load). The platen is mechanically mounted to a flex circuit, and impact to the platen can sever the flex circuit from the sensor.

Bluff: a platen pressure rating quoted as if it covers both modes. A push rating is in newtons per square millimetre; an impact rating is in joules. They are not interchangeable.

Row 9: Escutcheon pull-off (fastener retention) — axial pull, axial push, lateral, torsional

The escutcheon is the trim plate or the panel that holds the lock to the door. Pull-off is the test where a fixture pulls the escutcheon normal to the door face, and the rating is the force at which the screws yield, the escutcheon deforms, or the door substrate crushes. This is the row most suppliers skip because the cheapest escutcheons fail quickly and a quoted number is uncomfortable for the catalogue.

Bluff: an escutcheon pull-off rating quoted as a single number without naming the door substrate. Particle-board hollow-core and hardwood solid-core substrates differ in fastener retention by a factor of three or more. Demand the substrate.

Row 10: Battery-cover retention — axial pull

A pry-off battery cover is more than a serviceability nuisance — it is also a tamper path. The cover is held by clips, screws, or a slide-and-click latch. The test fixture applies an axial pull on the cover's pull-tab edge, and the rating is the force at which the cover releases (functional) or the clips yield (destructive). A cover that releases under Y newtons is a cover that an attacker can defeat under Y newtons; a cover that requires more force than the surrounding plastic can take is a cover that breaks before it opens.

Bluff: a battery-cover rating quoted without describing the failure mode (functional release vs break). Ask which side of the threshold the rating sits on.

Row 11: Strike-plate / keeper pull-out — shear

The strike is the metal plate on the door frame into which the bolt or latch projects. Pull-out is the test where the strike is anchored to a substrate (wood, steel, composite) and a force is applied along the bolt axis; the rating is the substrate-dependent force at which the screws yield or the substrate crushes.

Bluff: a strike pull-out rating quoted without the substrate. Different locks ship with different strike geometries (lip strike, full lip, ASA strike, deadbolt strike), and different substrates hold screws at different rates. Demand the substrate the supplier tested against.

Row 12: Integrated door sag — shear

A door in service sags over months. Sag redirects forces: a bolt that was designed to take pure axial push now takes a moment-loaded axial push. Sag is the integrated-door equivalent of running the matrix at the production door for twelve months. The buyer's worksheet records door-sag angles at install and at month-twelve and asks the supplier whether any of the matrix ratings change at non-vertical installation.

Bluff: a supplier that quotes ratings for a "vertical installation" but does not state the deviation angle the ratings hold to. A lock that keeps its ratings at zero degrees of door sag may not keep them at three degrees.

Row 13: Environmental seal integrity (after load) — impact

A lock's seal is rated separately (Smart Lock Water Resistance Testing owns water resistance, Smart Lock Salt Spray Testing owns salt spray). The reason this row exists in the mechanical-load matrix is that a load event can break the seal. A reader-window impact that does not crack the platen can crack the seal gasket. The post-load seal check is the cell that connects mechanical load to environmental resistance; treating either in isolation leaves the audit incomplete.

Bluff: a seal rating quoted without a precondition. A seal tested on an unstressed lock and a seal tested on a load-stressed lock can read identically on the gauge and mean different things on the door.

Per-model rule (to verify in writing — check the product page)

Three lines of discipline have to be written out plainly because every supplier conversation eventually drifts past them:

  1. Load ratings are per-model — SLK-9936S, SLK-9936G, SLK-9951TH, SLK-9962S, SLK-8831, SLK-G200 and the rest of the catalog each carry their own ratings. A kg/N/Nm figure for one lock does not port to another.
  2. Load ratings are per-direction — a single number with no direction is not a rating; it is a brochure.
  3. Load ratings are per-substrate when substrate matters — strike ratings, escutcheon ratings, fastener-retention ratings all depend on the substrate the supplier tested against. Substrate changes the rating; quote both or quote neither.

Where to look up the numbers that this datasheet deliberately leaves out:

  • For SLK-9936S — the verified product page (Keypad Hotel Smart Door Lock). This datasheet quotes the architectural facts that appear on the PDP and crosses nothing about load to that block: door thickness 36–100 mm, RFID Mifare 1 @ 13.56 MHz, read distance 0–5 cm, read time <0.25 s, power 4 × AA, battery operating cycles above 15,000, audit/event records up to 1,000, 5-pin cylinder, 3-point latch, stainless steel + alloy body, multiple finish options, mechanical emergency access, multilingual management software, standalone or centralized database modes, positioned for 1–5 star hotels. Load ratings are not on this list; for loads, check the model’s published specification.
  • For SLK-9936G, SLK-9951TH, SLK-9962S, SLK-9905A, SLK-8831, SLK-1104, SLK-G200, the outdoor/aluminum D-series, the cabinet locks, and every face/camera model — the verified PDP slug in the catalog spec base. Each PDP carries the load ratings that apply to that model only; do not bring them across models.
  • For locks not yet on a PDP — get the rating in writing on the supplier's letterhead inside the contract annex. A rating quoted in an email and not in the annex is not a binding figure.

How the matrix is filled (illustrative scenario)

A scenario walks the matrix better than a description does. The one below is illustrative and explicitly hypothetical — a 140-room coastal resort considering a mechanical-load audit on a candidate lock before pilot install.

Step 1 — the bench sample. The supplier ships a bench sample of the lock under evaluation (two examples — call them Lock-A and Lock-B). Each sample is mounted to a substrate-matched door blank (36–50 mm composite, the resort's dominant door thickness).

Step 2 — direction-by-direction protocol. The buyer's QA team works row by row. For row 1 (handle static load), three gauges are used: axial pull on the handle (Lock-A yields the lever screw at the supplier's quoted axial-pull rating; Lock-B holds to the rating with margin), axial push (Lock-A's push rating is the same as pull, as published; Lock-B's push rating is 18 percent lower, not advertised), and lateral (Lock-A's lateral rating is 30 percent of its axial rating — this is the cell the supplier omitted from the brochure; Lock-B's lateral rating is 60 percent of axial, advertised in the annex).

Step 3 — the bluff catches. The supplier's catalogue shows Lock-A at "static load N newtons" with no direction. Lock-A's pull rating is competitive; its push rating is competent; its lateral rating is below what the coastal resort's slammed-doors traffic pattern requires. Lock-B's annex carries all three ratings. The two locks look comparable in the brochure and are not comparable in the matrix.

Step 4 — the row-9 surprise. The escutcheon pull-off test (row 9) is the cell neither lock's brochure mentions. Both locks perform to the buyer's expectation on the composite substrate, but one lock's escutcheon relies on two screws and the other's on four. The four-screw version is the cell whose absence made the buyer's pilot-floor fail four years ago on a different project.

Step 5 — the worksheet sign-off. Row by row, the QA team signs off or sends the row back. The matrix does not admit partial passes: a row with a force number but no direction is not signed off; a row with a substrate mismatch is not signed off; a row that reveals a number the supplier's brochure omits is not signed off either — it is escalated to the supplier for written confirmation.

The pilot-floor lock is whichever lock's matrix ends with all cells signed off and all bluff flags resolved in writing.

The same five steps read as a sequence between the buyer's QA team, the bench hardware, and the verified product page:

sequenceDiagram
    participant B as Buyer QA team
    participant S as Bench samples on substrate-matched door blanks
    participant F as Pull · push · torque and drop-weight gauges
    participant P as Verified product page
    B->>S: receive two bench samples and mount each to a substrate-matched blank
    B->>F: run row 1 axial pull · axial push · lateral and the torque rows
    F-->>B: force · displacement · observation per direction
    B->>P: compare each result against the per-model rating
    P-->>B: direction-quoted rating · or a blank that is a question not a pass
    B->>S: sign off the cell · or escalate the bluff flag for written confirmation

What to put in the RFQ (load-evidence demands)

The mechanical-load evidence is best demanded before RFQ, not after the first delivery. The RFQ section to add — a paragraph-and-table the buyer pastes into the request — reads approximately like this:

Mechanical load evidence: For each candidate model, supply per-direction static-load ratings (axial pull, axial push, lateral) at the handle; torsional rating at the lever; torsional and shear ratings at the cylinder and bolt; impact rating at the reader window and the fingerprint platen; axial pull-off rating at the escutcheon and battery cover; substrate-named strike pull-out rating. Each rating must name the test fixture, the loading rate, the failure criterion, and the substrate where substrate is a factor. Ratings not quoted per direction will be treated as not quoted. Ratings matched against the verified product page will govern; ratings not on the verified product page will be added to the contract annex.

Four things to refuse when they come back on the RFQ:

  1. A "single-number handle rating" with no direction. Refuse.
  2. A bolt thrust rating without a shear companion. Refuse.
  3. A strike rating without a substrate. Refuse.
  4. An escutcheon pull-off rating the supplier declines to publish because "every substrate is different." Accept the answer, send the substrate back as a parameter — the supplier returns a substrate-named rating. Refusal to return a substrate-named rating is itself an answer.

How mechanical load connects to the rest of the testing thread

The mechanical-load matrix does not stand alone. Three neighbour tests sit next to it; this datasheet cross-references them so the buyer does not run them twice and does not skip them by accident:

  • Cycle testing (534 sibling). A lock that holds a kg of axial pull but fails after a thousand handles cycles is a lock whose load rating is correct and whose cycle rating is wrong. The cycle sibling owns the count.
  • Environmental testing. Salt, humidity, water, and temperature degrade the same fasteners and substrates the load matrix tests on day one. A load rating on day zero and a load rating on month eighteen are not always the same number; the environmental siblings own the cadence — see Smart Lock Humidity Testing and the rest of the environmental cluster.
  • Motor life testing (542 sibling). The motor is the actuation system; the load is what the actuation has to overcome. A lock with a strong mechanical load rating and a short motor life is a lock whose handles grip but whose motor gives up. The motor sibling owns the gearbox side.

Sign-off block (what the QA team's stamp looks like)

The datasheet is not complete without a sign-off block the QA team can physically stamp. A printable version reads:

CellEvidence locationWitnessSign-off
Row 1 — axial pullbench sample, fixture XYZ, substrate ABCname + role☐
Row 1 — axial pushbench sample, fixture XYZ, substrate ABCname + role☐
Row 1 — lateralbench sample, fixture XYZ, substrate ABCname + role☐
Row 2 — torsionalbench sample, torque wrench, lever length notedname + role☐
Row 4 — cylinder torsionbench sample, torque wrenchname + role☐
Row 4 — cylinder shearbench sample, fixturename + role☐
Row 5 — deadbolt axialbench sample, push ramname + role☐
Row 5 — deadbolt shearbench sample, fixturename + role☐
Row 6 — latch push-backbench sample, fixturename + role☐
Row 7 — reader impactbench sample, drop-weight, joulesname + role☐
Row 8 — platen pushbench sample, calibrated pressname + role☐
Row 8 — platen impactbench sample, drop-weight, joulesname + role☐
Row 9 — escutcheon pull-offbench sample, fixture, substrate notedname + role☐
Row 10 — battery coverbench sample, fixturename + role☐
Row 11 — strike pull-outbench sample, substrate namedname + role☐
Row 12 — door saginstall + month-twelve field readingname + role☐
Row 13 — seal after loadbench sample, load + seal recheckname + role☐

A blank sign-off is a question, not a pass. The matrix is complete only when every cell's rating has been sourced from the verified product page, every witness has been named, and every stamp is on the page.

Closing the datasheet

Mechanical-load testing is not a question of "does the lock hold" — it is a question of "in which direction, on which substrate, after how many cycles, with what fixture, against what rating, witnessed by whom." A B2B procurement programme that treats the load matrix as a single number has already lost the audit to the brochure. A programme that runs the matrix row by row, with per-direction ratings routed to the verified product page and per-model discipline held throughout, is a programme that catches the bluff in week one rather than year three.

The next datasheet the buyer's QA team should run on the same candidate locks is the cycle-count datasheet (533 sibling) and, on motor-driven models, the motor-life datasheet (542 sibling). The three datasheets together — mechanical load, cycle count, motor life — form the mechanical-evidence trilogy; the security datasheet (501 sibling) and the durability checklist (533 sibling) carry the rest of the testing thread. None of the four datasheets is complete without the others; the matrix above is one of four.

When the matrix and its three siblings all sign off, and the per-model load ratings are written into the contract annex, the lock is ready for pilot-floor install.

Troli Belian Anda
Pengalaman anda di laman ini akan Improved dengan membenarkan kuki Dasar Cookie
Chat on WhatsApp