Keypad Only Versus Glass Clamp: Which Fits a Co-Living Door Programme
This process document turns the keypad only versus glass clamp co living comparison into a sequence of procurement gates. It helps an operator decide where a keypad only lock belongs, where a glass clamp smart lock belongs, and where neither should be forced into service. The sequence moves from a door register to measured samples, access testing, commercial evaluation and controlled handover.
Direct answer. The short answer is that keypad only versus glass clamp co living comparison is not one decision. It is a sequence. This article takes keypad only versus glass clamp co living comparison from keypad only versus glass clamp co living comparison through glass-clamp to the record you keep. A keypad only versus glass clamp co living comparison scores alternatives against criteria a buyer can defend. keypad only versus glass clamp co living comparison is the criterion that eliminates the most keypad only versus glass clamp co living comparison candidates.
- Agree the test — name the criteria for keypad only versus glass clamp co living comparison before comparing anything
- Rank on the same test — score every option against glass-clamp the same way
- Make the concession explicit — say what each option in gate mapping costs you
- keypad only versus glass clamp co living comparison runs this sequence, and glass clamp is the record it produces.
Co-living access control combines two very different conditions. Private unit doors are used almost exclusively by residents, while shared kitchens, workspaces, a bike store and parcel lockers can experience high daily traffic. Residents expect privacy at their unit entrance and convenient access to common areas. That makes one question central to every door: which openings need traceable events, and which only need a dependable opening path?
Use this as a procurement site survey and approval record. Property operations, building services and the access-control owner should approve the same door schedule. A candidate then passes only after its construction fit, credential flow, failure behavior and handover evidence are complete. Model-level dimensions and capabilities remain SKU-specific; confirm on the dated product page for the specific SKU whenever a catalogue field drives a purchase.
Gate map for the selection sequence
The comparison should run as a dependency-based process. Each gate prevents a commercial decision from outrunning the physical and operational evidence needed to support it. The sequence below assigns an owner and an exit condition to every stage.
| Gate | Sequence point | Procurement action | Owner | Exit evidence |
|---|---|---|---|---|
| G0 | Before shortlisting | Register every in-scope door and its users | Operations lead | Signed door and access register |
| G1 | Before sampling | Freeze access, safety and construction requirements | Access-control owner | Requirement schedule and exclusions |
| G2 | After field survey | Measure each door and test construction assumptions | Surveyor with installer | Dimensioned survey record |
| G3 | Before pilot | Match measured doors to specific candidate SKUs | Product evaluator | Door-by-door candidate schedule |
| G4 | During pilot | Test daily use, failure paths and event visibility | Pilot manager | Signed test results |
| G5 | Before commercial award | Score supported proposals and document gaps | Procurement manager | Evaluation record |
| G6 | After award | Freeze product configuration and approved substitutions | Procurement and supplier | Approved product schedule |
| G7 | Before handover | Train operators and transfer documentation | Property operations | Handover pack and training record |
flowchart TD
A[Register doors and access needs] --> B[Freeze non-negotiable requirements]
B --> C[Measure construction and hardware space]
C --> D[Shortlist keypad only candidates]
C --> E[Shortlist glass clamp candidates]
D --> F[Run management and failure tests]
E --> F
F --> G{Acceptance evidence complete}
G -->|Pass| H[Approve product schedule]
G -->|Revise| I[Change design or exclude door]
Do not collapse G2 and G3. A candidate that appears suitable in a catalogue may still fail because the existing door has no usable backset, the glass has no safe clamp zone or the required event records are absent from the selected configuration. The gate exists to make that failure visible before an order is placed.
Register doors before comparing products
The first deliverable is a door register, not a product list. Divide the portfolio by construction, occupancy and opening pattern. A unit entry door with a standard swing leaf should not sit in the same decision line as a framed glass partition, even if both are described as shared-space doors.
| Door class | Typical use in the programme | Main opening requirement | Access question to record |
|---|---|---|---|
| Private unit entry | Resident-controlled private area | Secure daily access with a traceable resident event | Does each resident need an individual event or only valid entry? |
| Shared kitchen or workspace | Frequent resident and staff use | Fast repeat access with controlled guest access | Are schedules and temporary credentials required? |
| Bike store or service room | Resident access plus scheduled staff access | Clear opening windows and emergency procedure | Does the staff window need separate reporting? |
| Parcel or ancillary room | Short, irregular access | Reliable opening with minimal management overhead | Is an audit trail worth the operating burden here? |
| Glazed internal door | Visual connection or controlled shared area | Glass-safe mounting and unobstructed operation | Is a clamp body appropriate for this exact leaf? |
Co-living operations should ask the access question before selecting hardware. Recording an audit trail on every door can create unnecessary administration and resident friction. Conversely, omitting records from a unit door may make disputes harder to resolve. The product follows the access design; it does not create the design by itself.
Use the field discipline in the Office Smart Lock Site Survey for the initial register and the Smart Lock Retrofit Site Survey when existing openings must be assessed. Keep resident identities out of the engineering survey unless the security owner has approved that data treatment.
Freeze the requirement set before product naming
A useful requirement schedule prevents “keypad” from becoming an ambiguous category label. For this comparison, a keypad only lock means that the resident-facing unlock method is a passcode; fingerprint, RFID/IC card and mobile app access are not treated as resident unlocking methods for that door. A glass clamp smart lock describes the installation architecture, not a universal credential set. The selected glass-clamp SKU must provide the access method required by the door.
| Requirement field | Keypad-only decision question | Glass-clamp decision question |
|---|---|---|
| Primary access | Is passcode access sufficient for this door class? | Which credential method does the proposed clamp configuration provide? |
| Event evidence | Which actions must create retrievable records? | Can the clamp configuration produce the required event records? |
| Existing construction | Can a lock body, spindle, latch and strike be installed safely? | Is there a suitable clamp, patch fitting or mounting zone on the glass? |
| Emergency opening | What mechanical or controlled fallback is required? | What safe release path applies to this glazed door? |
| Power resilience | What low-battery indication and external-power provision are required? | What power arrangement is possible without unsafe glass modification? |
| Administration | Who creates, changes and removes resident access? | Who manages access without creating extra shared-space administration? |
| Visual finish | Is the escutcheon acceptable on this door? | Are clamp, patch fitting and finish acceptable to residents? |
| Maintenance access | Can technicians service the lock without door replacement? | Can the glass component be serviced or replaced separately? |
Door hardware compatibility is therefore a door-level conclusion, not a catalogue-wide label. Make the requirement schedule non-negotiable before candidates are scored, but leave the model and configuration open. If a requirement is negotiated later, record who approved the change and which test must be repeated.
CONFIRM-WITH-LOCAL-AUTHORITY: Ask the authority and building professional responsible for each site to confirm the applicable access, life-safety and accessibility requirements; this workflow does not replace that review.
Compare physical fit door by door
Gate 3 is where the keypad only versus glass clamp co living comparison becomes a survey exercise. A keypad-led lock normally interacts with a standard swinging door through a lock body or mortise, spindle, latch or deadbolt, strike plate and escutcheon. A glass clamp interacts with the glass assembly through a clamp body and associated patch or mounting hardware. These are different construction problems, even when both products present a keypad.
| Fit field | Keypad-only route | Glass-clamp route |
|---|---|---|
| Primary construction | Timber or metal swing door with suitable lock preparation | Framed glass door or partition with a usable mounting zone |
| Critical dimensions | Leaf thickness, rebate, backset, spindle position and handle geometry | Glass thickness, clamp zone, rail position, edge clearance and fixing arrangement |
| Lock interface | Mortise case, latch or deadbolt, spindle, cylinder and strike keeper | Clamp case, glass patch fitting or approved mounting arrangement |
| Existing hardware | Existing handle, closer and strike may affect preparation | Door closer, pivot, floor spring and patch fittings may constrain the clamp |
| Door changes | Drilling or cutting may be needed if preparation is unsuitable | Drilling, patching or glass replacement may be needed if the zone is unsuitable |
| Service access | Technician access depends on escutcheon, lock body and strike layout | Damage may affect glass, clamp or patch hardware; separate replaceability matters |
| Power arrangement | Battery compartment and external-power provision are SKU-specific | Battery compartment, cable route and external-power provision are SKU-specific |
| Safe fallback | Override, release and exit behavior must be demonstrated | Release, override and safe operation must be demonstrated on the installed door |
The factory catalogue contains 79 published models. It places 18 in Keypad Door Lock, three in Glass Door Locks and 55 with a recorded passcode/keypad function. Those figures describe catalogue breadth, not project suitability. The small glass segment reinforces the need for exact SKU evidence rather than a general claim about glass hardware.
One catalogue example shows why product naming needs discipline. The SLK-1101 is listed as a keypad smart door lock with a grip handle, but its record also includes fingerprint access. Its listed door fit is 35–60 mm for wood or metal doors, with a 60/70 mm adjustable single-latch mortise. It therefore should not be treated as evidence of keypad-only suitability. They are not substitutes for the dated product page, dimension drawing or installation guide for an approved SKU.
Test the access design and management burden
Shared access management should be tested separately from the physical lock. A keypad can open a door while still creating weak governance if every user knows one shared code. A glass clamp can offer a suitable credential method while sitting in the wrong management system for a private unit. Start with the access journey, then identify the hardware and software functions needed to support it.
| Access journey | Required behavior | Evidence to capture |
|---|---|---|
| Resident enters private unit | The resident uses an individually controlled credential without depending on a shared code | Credential assignment, expiry, removal and event visibility |
| Resident enters shared kitchen | A resident can enter routinely without waiting for staff | Reopening frequency, user administration and exception handling |
| Staff enters during scheduled window | Staff access is limited to the approved operating period | Validity window, override authority and event sequence |
| Guest or contractor enters | Temporary access can be issued and removed | Temporary credential creation, expiry and audit trail |
| Battery or power condition changes | The user receives an actionable warning and the operator can respond | Low-battery behavior and documented fallback process |
| Network or platform service is unavailable | Local access and safe fallback remain within the approved design | Tested offline behavior for the selected configuration |
| Resident reports a disputed entry | An authorized operator can retrieve the relevant event | Event scope, timestamp basis and retrieval procedure |
Do not assume that a keypad model records events or that a clamp model integrates with the programme’s management platform. Request those functions for the specific SKU and configuration. Likewise, remote opening, role-based permissions and temporary access should be treated as requirements to verify, not inherited from a similar product.
The private/shared distinction also changes the acceptable operating burden. A frequently used shared door may justify scheduled credential issuance and regular review. A rarely used private door may need a simpler resident experience. Shared access management should be proportional to the traffic and dispute risk recorded at G0.
Move from candidates to controlled samples
Samples close the gap between a catalogue record and an installed door. Give the supplier a door schedule, the relevant measurements and the access scenarios that the pilot must demonstrate. Ask it to identify the exact proposed SKU and configuration in writing before a sample is accepted.
| Pilot test | Method | Pass condition | Record |
|---|---|---|---|
| Fit | Install the sample on the represented door without unapproved workaround | Door operates as intended and no unsafe modification is required | Photographs and marked drawing |
| Daily opening | Repeat the normal entry action across the user group | Users can complete the journey without confusion | User observations |
| Repeated use | Operate the lock through the planned access pattern | No change in reliability that creates an operating burden | Test counter and observations |
| Incorrect entry | Attempt a wrong or inactive credential | The door stays secure and the event behaves as specified | Result and event record |
| Low battery | Follow the approved simulation method | Warning appears early enough for the stated response process | Result and response time |
| Fallback | Use the approved emergency or service method | Safe operation is demonstrated and the event is recorded where required | Signed result |
| Management | Create, modify and revoke access | Each required action can be completed and traced | Screenshots or exported records |
| Handover | Label, document and train the pilot users | Support staff can identify configuration and procedure | Training record |
Treat the pilot as an evidence stage, not a sales demonstration. Record the door used, the exact configuration, the tester and any deviation from the written procedure. A product that passes only on a purpose-built display door should not pass the programme gate.
Keep the candidate count disciplined. One keypad-led model and one glass-clamp model may be enough to expose the construction and management differences. More candidates become useful only when they answer a defined requirement that the first pair cannot satisfy.
Score the supported comparison without false precision
A weighted worksheet helps procurement compare complete proposals while preserving the evidence from earlier gates. Use weights as a starting structure and adjust them before viewing supplier responses. The table below is a proposed decision aid, not a market benchmark.
| Criterion | Suggested weight | Scoring evidence |
|---|---|---|
| Door and glass fit | 25 | Measured fit and approved installation detail |
| Access journey | 20 | Pilot results for the assigned door class |
| Event and management capability | 15 | Verified functions in the proposed configuration |
| Failure and fallback behavior | 15 | Documented and witnessed test results |
| Maintenance and replaceability | 10 | Service procedure and component strategy |
| Resident usability | 10 | Pilot observations and training outcome |
| Documentation and OEM/ODM control | 5 | Available drawings, manuals and configuration records |
Score each candidate from evidence already filed. A missing document is not a neutral midpoint; it is an unresolved risk. Record the score, the unresolved issue and the corrective action. If two candidates are close, use the door schedule to identify which difference matters operationally rather than inventing a new weighting after the result is known.
The decision comparison table should remain readable after the programme is under way. It should point back to the survey, pilot results and approved product schedule, allowing a later operator to understand why a candidate was accepted for one door class and rejected for another.
Approve the schedule and control substitutions
At G6, convert the evaluation into a controlled product schedule. Each line should identify the door or door class, proposed SKU, configuration, finish, installation drawing reference, management method and responsible approver. This prevents a successful keypad sample from being copied to a glass door or a different backset without another check.
| Approval record | Required entry |
|---|---|
| Door reference | Door ID, location, leaf type and construction |
| Product reference | Exact model name and dated product-page review |
| Configuration | Access methods, power arrangement, finish and management route |
| Fit reference | Survey record, drawing and approved installation detail |
| Test reference | Applicable pilot results and unresolved-risk disposition |
| Substitution rule | What may change without a new site check |
| Approver | Operations, access-control owner and procurement sign-off |
Keep product references and configuration references together. A model name alone may leave the access method, software route, finish or hardware interface ambiguous. Where an OEM/ODM package is requested, ask for logo, finish, packaging, manuals and product configuration as separate recorded items.
For retrofit projects, recheck the assumptions with the Smart Lock Retrofit Site Survey. For a new standard door, the Office Smart Lock Site Survey provides a useful starting structure. Any substitution that changes the door interface, credential method, event function or power arrangement should return to the relevant pilot gate.
How the route changes across illustrative door scenarios
The following scenarios are illustrative planning examples, not case studies. They show why a portfolio-level rule produces poor results. The same product family may be appropriate on one door and unsuitable on the next.
| Illustrative scenario | Recommended route | Reason |
|---|---|---|
| Timber unit door with existing lock preparation and controlled resident use | Keypad-only candidate, subject to measured fit | The standard swing-door interface and individual access requirement support this route |
| Frequent shared kitchen with a glazed upper section and separate service swing door | Evaluate the glazed leaf as glass clamp and the swing door separately | One room can contain two construction types and different opening needs |
| Bike store with a steel door and scheduled staff entry | Keypad-led candidate with staff validity windows | A standard lock interface and scheduled access can address the stated pattern |
| Newly installed frameless glass partition without a defined mounting zone | Hold selection until the door fabricator confirms fit | Glass dimensions, patch hardware and safe operation must be evidenced |
| Parcel locker or low-traffic utility door | Use the simplest configuration that meets the access need | An unnecessary management burden may cost more in administration than it adds in control |
The key question remains door-specific: what must the opening do, and what construction is already present? Use the first-party facts about co-living traffic only to frame that question; do not let a shared-door scenario overwrite the privacy requirement of a private unit.
Procurement package for a comparable quotation
A request for quotation should place the same evidence demand on both routes. It should identify the door survey, access scenarios, management requirements and test evidence, rather than asking only for a lock and a glass clamp as generic items.
| RFQ field | Instruction to bidders |
|---|---|
| Door schedule | Include door IDs, construction, dimensions, door type and intended user group |
| Product mapping | Propose a specific SKU and configuration for each door class |
| Dimension drawings | Provide installation drawings for the proposed body and interfaces |
| Access methods | State which methods are included in the proposed configuration |
| Management functions | Describe user, schedule, temporary-access and event functions |
| Event evidence | State what is recorded and how an authorized operator retrieves it |
| Power and fallback | State the power arrangement, warning method and approved fallback |
| Installation conditions | Identify any frame, glass, rebate, handle or closer constraints |
| Documentation | Provide the installation guide, datasheet and available configuration records |
| Sample and support | Propose the sample, pilot and technical-support sequence |
Do not let a bidder infer a whole programme from one showcase door. Include the relevant composite door drawings, particularly where a room combines a glazed panel, swing leaf, closer and access-control hardware. The exact model proposed for each construction type should be visible in the response.
The dated product page remains the source to verify a specific SKU. The request for quotation should also state which evidence is required at each stage of the gate sequence.
Pilot acceptance and handover evidence
Acceptance should link each installed door to its test record. Property operations should be able to answer three questions without searching through scattered messages: what is fitted, who approved it and how is it supported?
| Handover item | Minimum evidence |
|---|---|
| Installed-door register | Door ID, exact SKU, configuration and installation reference |
| Access register | Active credentials, expiry rules, owners and authorized administrators |
| Test archive | Fit, daily-use, failure, fallback and management test results |
| Event procedure | How authorized staff retrieve records and interpret timestamps |
| Battery procedure | Warning response, replacement steps and escalation route |
| Service procedure | Maintenance access, replaceable components and supplier contact route |
| Training record | Resident, operator and maintenance briefings |
| Change control | Reapproval triggers for model, configuration, door or software changes |
The handover pack is also the baseline for future expansion. A new door, replacement glass or different furniture can change the fit even when the property retains the same access policy. Use the Office Smart Lock Site Survey link as the survey reference, then return the amended record to the appropriate gate instead of treating the earlier approval as permanent.
The decision procurement can defend
At the final gate, a defensible result may select keypad only locks for selected standard swing doors, glass clamp smart lock configurations for verified glazed doors, or different architectures across the same co-living portfolio. The important point is not the quantity selected. It is that each door has a traceable basis: measured fit, tested access, demonstrated fallback, verified management and approved documentation.
For a separate view of option weighting, use Keypad Only Versus Glass Clamp: Decision Matrix for Co-Living Operators. Keep this document focused on the sequence, gates and evidence needed to move that comparison into a co-living programme without unsupported substitutions.
The next commercial action is to send the completed door register and survey pack for review. Ask the supplier to map a named candidate to each door class and state what must be confirmed on the dated product page for the specific SKU before approval.
Ask for the offer against the same requirement: request a quote.

