Reading Housing Materials and Wall Thickness Claims in a Supplier Datasheet
At qualification stage, a supplier datasheet is a set of claims to verify, not a fit approval. This brief on housing materials and wall thickness datasheet claims helps a System Integrator identify what each statement covers, what evidence is needed, and whether the record supports approval. A material name without a component boundary, or a thickness range without a measurement basis, leaves the door-fit question unanswered.
Direct answer. In short, housing materials and wall thickness datasheet claims is the subject of this piece. housing materials and wall thickness datasheet claims is where the work on housing materials and wall thickness datasheet claims sits. housing-materials-and-wall-thickness is what has to be evidenced before anyone signs. A housing materials and wall thickness datasheet claims is a component behaviour guide. It covers limits. It covers failure modes. housing materials and wall thickness datasheet claims decides whether housing materials and wall thickness datasheet claims is acceptable for this build.
Throughout, housing materials and wall thickness datasheet claims means what housing materials and wall thickness datasheet claims sets out. It is a working definition of housing materials and wall thickness datasheet claims drawn from the evidence below. It is valid for the specific market and product, not as a general claim.
Qualification scope: separate configuration from acceptance
Start by splitting every statement into three subjects: panel/body material, applicable door thickness, and housing section or gauge. These are different design variables. Record which escutcheon or panel, lock body/mortise, strike plate, latch, and door leaf the claim covers. A material statement for the escutcheon cannot automatically be carried to the lock body, while a door-thickness range is not a housing-wall measurement.
For supplier qualification, create a claim register before requesting samples. Name the proposed configuration, document revision and date, affected door, measuring method, and person who accepted the evidence.
Evidence route from claim to approval
Use one route for every line so a favorable material statement does not conceal an unresolved fit statement. The decision is evidence-based and reversible when a drawing or SKU changes.
flowchart TD
A[Claim received] --> B{Claim type identified}
B -->|Material| C[Define affected part]
B -->|Door fit| D[Define measurement basis]
B -->|Both| E[Split the claim]
C --> F[Review dated evidence]
D --> F
E --> F
F --> G{Quality decision}
G -->|Accepted| H[Record approval]
G -->|Conditional| I[Request correction or sample]
G -->|Rejected| J[Hold the SKU]
Review rule for housing materials and wall thickness datasheet claims: rewrite each statement so its component, measurement basis, and evidence boundary are visible.
| Supplier wording requiring review | Required clarification | Evidence attachment | Qualification consequence |
|---|---|---|---|
| Material name without component scope | Identify each affected part and material designation | Controlled drawing and supporting material record | Material identity remains open if component scope is absent |
| Numeric thickness range | State whether it is applicable door thickness and explain measurement conditions | Dimension drawing and site measurement record | Door fit cannot be assessed from the range alone |
| Environmental wording without conditions | Define the exposure conditions and affected model versions | Supporting report and configuration mapping | Wording remains conditional until linked to evidence |
Material wording that survives technical review
For panel/body material, require the material designation, affected component, finish or surface treatment, and any grade detail the supplier is prepared to evidence. Do not treat a material family name as a complete answer: request its grade, scope, and applicable drawing. If a second material is listed, ask which parts use it and what record supports that statement. A supplier may also offer documentation: dimension drawings, an installation guide, and a datasheet on request, but each document needs an identifier and revision.
For an external housing, ask for evidence behind any weather-resistance or durability wording instead of repeating the phrase as a result. Material evidence may include a declaration, inspection record, or test report, depending on the claim. Record what the document proves, who issued it, and which model versions it covers.
Wall thickness: resolve the measurement basis
The phrase “wall thickness” can mean door leaf thickness or the section of a housing wall. A qualification record must identify the meaning. For door installation, use applicable door thickness and state whether the range is measured before or after rebate. Also record backset, spindle position, mortise case geometry, strike keeper position, and the clearance required by the door closer or escape hardware. A range that excludes the actual door should close the qualification gate even if the housing material is acceptable.
For an internal housing section, request a sectional drawing with dimensions and revision. Compare that drawing with the part being quoted; an escutcheon drawing cannot clear a different lock body/mortise. If the supplier proposes a range, ask for the test condition: actual installed door, finished door, or sample mock-up. The installation guide should use the same measurement basis as the team taking site measurements.
First-party anchor and its limit
The supplied SLK-9936S hotel-lock record lists 36–100 mm door thickness and a stainless steel + alloy body. Treat this as a worked example of wording that must be checked, not evidence that another variant shares the same range or material mix. Confirm on the dated product page for the specific SKU before using it in a fit, sourcing, or approval decision.
Qualification decision comparison
The decision matrix links each evidence condition to a procurement action rather than treating every datasheet response as equivalent.
| Decision | Datasheet position | Required evidence | Procurement action |
|---|---|---|---|
| Accept | Complete, internally consistent, and tied to the quoted configuration | Controlled drawings, material definition, installation instructions, and resolved measurement basis | Record approval against the exact SKU and door specification |
| Conditional | Plausible claim with a missing scope, revision, or condition | Corrected statement, attached evidence, or a representative fit check | Approve only the qualified configuration and open a re-review condition |
| Hold | Contradictory claim, uncovered variant, or unresolved door-fit conflict | New supplier response and renewed technical review | Exclude the configuration from approval until the conflict is closed |
Minimum evidence request
Ask for one controlled package containing: current dimension drawings; the panel/body material definition by component; the applicable door thickness with measurement conditions; the installation guide; supporting records for each claimed environmental or durability property; and the datasheet on request with the exact model variants covered. Cross-reference every attachment to the claim register.
For deeper review, use Housing Materials and Wall Thickness Trade-Offs: Cost, Durability and Service to separate design choices, Housing Materials and Wall Thickness Failure Modes Seen on Smart Lock Projects to structure fault questions, and Housing Materials and Wall Thickness Test Evidence a Buyer Can Actually Request to evaluate attachments. Add site inputs through the Office Smart Lock Site Survey and Smart Lock Retrofit Site Survey workflows.
The same question is worked through in more detail in smart lock price by access method. That is the same question housing materials and wall thickness datasheet claims has to answer here.
Local regulatory gate
The technical package can close the material-and-fit question, but project acceptance may require additional local review. Keep that review as a separate recorded gate rather than implying that a supplier datasheet settles it.
CONFIRM-WITH-LOCAL-AUTHORITY: Confirm with the authority or client reviewer responsible for the installation location which project-specific requirements apply, and record the source, scope, date, and approved product configuration.
Approval record handed to procurement
Close each claim line with four entries: accepted statement, evidence reference, decision, and re-review condition. Attach site measurements and controlled supplier documents, then send the same scope through the request-a-quote workflow. If a drawing revision, door type, or SKU changes, reopen the affected line; a qualified material statement does not carry over automatically.

