EN 1906 in a Smart Lock Tender Pack: The Evidence Checklist
This qualification schedule turns en 1906 smart lock tender evidence into a bidder-completable record rather than a loose collection of certificates. EN 1906 concerns lever handle and knob furniture; it does not establish that the lock mechanism, radio, emergency-egress function or complete door assembly conforms to that standard. Procurement should therefore accept evidence for the offered furniture variant while separately identifying the evidence needed for the other parts of the smart-lock offer.
Direct answer. The short answer is that en 1906 smart lock tender evidence is not one decision. It is a sequence. This article takes en 1906 smart lock tender evidence from en 1906 smart lock tender evidence through en-1906 to the record you keep. an en 1906 smart lock tender evidence works as a two-column evidence test. en 1906 smart lock tender evidence names the documents. Each column of en 1906 smart lock tender evidence closes with a paper.
- What comes from the factory — supplier declarations and drawings for en 1906 smart lock tender evidence
- What needs an external body — third-party certificates covering the exact scope of en-1906
- What to order — the document set that matches the SKU behind en 1906 smart lock tender evidence
- This is the sequence en 1906 smart lock tender evidence has to follow, anchored on en 1906.
Use the schedule as a qualification attachment to the bid form. Require bidders to complete it for every lever handle or knob offered, identify the document behind every claim, and expose any gap before the offer enters technical or commercial evaluation. The standard describes what is tested. Site or product approval remains a question for the named evidence and the exact component placed in the contract.
Tender instruction: define the offer boundary before asking
A general request for an “EN 1906 compliant smart lock” gives bidders no reliable way to answer. The handle or knob may fall within EN 1906, while the lock body, electronics, credentials, door assembly and escape arrangements raise different questions. Replace that phrase with a component-specific instruction and a schedule of the evidence the buyer will examine. The build options sit in the smart door locks.
For each lever handle or knob included in the offer, identify the exact manufacturer product designation, finish, fixing configuration and applicable document. State whether the document is a test report, certificate, declaration of conformity or marking evidence. Identify the standard edition, tested sample, document number, issue date, scope, result, exceptions and verification route.
This en 1906 smart lock tender evidence schedule should form the bidder’s indexed response. A bidder may state that a document is not applicable, but the response must give a reason. Silence is not a compliance statement, and a document supplied for another lock component cannot be silently transferred to the furniture line.
Use this EN 1906 tender evidence checklist table to identify what belongs in each bid response:
| Bid-response field | Minimum bidder entry | Procurement check |
|---|---|---|
| Component offered | Lever handle or knob | EN 1906 scope fits |
| Exact product designation | Manufacturer reference and variant | No family-only description |
| Evidence requested | Report, certificate, declaration or marking | Document type is named |
| Evidence supplied | Title, number, revision and issue date | All identifiers are present |
| Result and exceptions | Pass/fail wording plus deviations | Scope is explicit |
| Verification route | Contact or database reference | Evidence can be checked |
| Approval status | Submitted, qualified, clarification or excluded | Decision is recorded |
This table should be issued with the tender documents, not requested informally after bid opening. It gives every bidder the same answer structure and lets the evaluation team compare evidence quality consistently.
Scope gate: separate furniture approval from lock and door
EN 1906 covers lever handle and knob furniture, including furniture durability, strength, corrosion and security characteristics. It does not answer questions about the lock mechanism. A smart lock bid must keep that boundary visible so that a valid furniture document is not presented as evidence for the complete locking product.
| Procurement question | Evidence boundary | Decision for the tender |
|---|---|---|
| How does the offered handle or knob perform? | EN 1906 furniture test evidence | Evaluate under the furniture schedule |
| How does the electromechanical lock operate? | Separate lock-performance evidence, such as EN 14846 where applicable | Require under the lock line |
| How does the complete fire-door assembly perform? | Assembly-level fire evidence, including EN 1634-1 where relevant | Require with the door package |
| What happens in an emergency exit arrangement? | Applicable escape-device evidence | Require from the door-safety specialist |
| How are radio and electromagnetic characteristics addressed? | Applicable radio, EMC and product-safety evidence | Require separately for the market concerned |
The scope gate is especially important when a bidder supplies a family brochure, a declaration for a related handle or a report whose sample description does not identify the offered configuration. The document may have technical value, but it does not close the furniture line unless the published scope and product identity connect it to the bid.
For a structured method for separating scope from broader smart-lock claims, use EN 1906 for Smart Locks: Scope, Tests and What the Standard Never Proves. The tender should then record which other standard or conformity route governs each non-furniture component.
flowchart TD
A[Receive bidder evidence] --> B{Does EN 1906 fit the offered furniture?}
B -- Furniture --> C{Is the document type named?}
B -- Other component --> D[Route to the relevant evidence schedule]
C --> E{Does the evidence identify the exact variant?}
E -- No --> F[Request clarification or record the gap]
E -- Yes --> G{Are issuer and issue data verifiable?}
G -- No --> F
G -- Yes --> H[Review scope, edition, result and exceptions]
H -- Meets tender criteria --> I[Record the qualified evidence]
H -- Unresolved --> F
Four records that must never be collapsed into one status
Procurement teams frequently hear that a supplier has “CE” or “EN 1906 evidence” without knowing which record is being offered. The tender checklist must name the record and prevent one category from standing in for another.
| Record | What the record is | What it contributes | What remains to be checked |
|---|---|---|---|
| Test report | A named body tested a sample under stated methods | Test conditions, sample identity and results | Whether the sample represents the offered variant |
| Certificate | A body attests conformity within a defined scope | Attestation, scope, number and validity | Whether the scope covers the exact item being bought |
| Declaration of conformity | The manufacturer or importer makes its own legal claim | The party’s declared basis and responsibility | Authority, signature, date, product identity and technical annexes |
| Product or label marking | A mark such as CE, UKCA, RCM, KC or G-Mark appears on an item or label | Visible identification of the mark claimed | Which document supports the claim and what the mark actually signifies |
A marketing image is not a record. A self-declared document is not a third-party certificate. A test report on a sample does not automatically cover a production variant. A certificate with a broad scope does not prove that every option within that scope was supplied. An EN 1906 furniture test report says nothing about radio, EMC, fire resistance or escape-device performance.
Treat every statement of certification as CONFIRM-PER-SUPPLIER until the named document, scope and verification route have been checked. Ask the bidder to explain the EN 1906 certificate scope, including the product references, covered variants and validity status stated in the document itself.
CONFIRM-WITH-LOCAL-MARKET-ACCESS-TEAM: Confirm which market-access marking and declaration route applies to the exact SKU and destination; EN 1906 evidence does not replace those destination-specific checks.
Evidence ladder: set the qualification threshold before bidders
The evidence-quality ladder gives procurement a practical way to compare submissions without pretending that every record has equal weight. Set the minimum acceptable rung in the tender instructions before receiving bids, then ask bidders to identify the rung their evidence reaches.
| Evidence level | Evidence available | Commercial meaning for qualification |
|---|---|---|
| marketing image | Product photograph, brochure or sales statement | Lead for due diligence only |
| self-declared DoC | Signed manufacturer or importer declaration | accountable claim, but no independent attestation |
| test report on a sample | Report for an identified sample | Technical result, subject to sample traceability |
| third-party certificate with scope and number | Certificate with scope and verifiable number | Independent attestation within its stated scope |
| certificate for the exact SKU/variant being purchased | Certificate covers the SKU and variant being bought | Strong fit to the procurement line |
| production-control records that hold the approval open after the sample passed | Audit or controls connect the qualified design to continuing production | Strongest link to the item supplied |
The failure pattern is familiar: a tender team accepts a declaration or generic report, then discovers during installation that no document covers the ordered configuration. That may leave the buyer with an unresolved qualification issue and an obligation to obtain further evidence before proceeding.
The threshold depends on the project’s risk and procurement purpose, but it must be stated. Do not imply that an image, a declaration and a certificate are interchangeable. Also do not require a specific evidence level without explaining what the project is trying to establish. The Who Pays for EN 1906 Evidence in a Smart Lock OEM Programme helps separate evidence ownership and commercial responsibility before the bid is issued.
EN 1906 evidence matrix: one row for every offered component
The EN 1906 evidence matrix is the main working sheet of the tender pack. Create one row for each offered furniture item. Do not combine a range of handles into one row if their references, finishes or fixing arrangements differ.
| Matrix field | Bidder response | Evidence attachment |
|---|---|---|
| Bid line and component | Furniture type and intended door use | Product schedule |
| Manufacturer product reference | Full designation and variant | Datasheet or product record |
| Finish and material | Exact offered description | Product record |
| Fixing or mounting arrangement | Relevant configuration details | Drawings or product record |
| Document type | Report, certificate, declaration or marking | Original supplied document |
| Standard designation | EN 1906 and the published title | Document cover or scope page |
| Edition | Edition shown in the document | Title page or explanatory annex |
| Tested sample | Manufacturer reference and distinguishing features | Report sample description |
| Document number | Full identifier and revision | Report or certificate |
| Issue date | Date shown on the signed or issued record | Document |
| Scope | Products, configurations and exclusions stated | Scope page |
| Result | Outcome and any classification wording | Result page |
| Exceptions or deviations | Full wording or a confirmed none | Report annex |
| Validity | Expiry, reissue or continuing-status wording | Certificate or issuer statement |
| Verification | Database, issuer contact or document route | Verifiable reference |
| Evidence owner | Bidder, manufacturer or other named party | Responsibility schedule |
The bidder must not replace a field with “as supplied”, “standard” or “see attached”. Those phrases conceal the very information the buyer needs to compare bids. A missing field should be recorded as missing, followed by the clarification question required to close it.
Keep source files in the tender pack where access and confidentiality rules allow. A PDF image without searchable identifiers can still be reviewed, but the matrix should transcribe the key data so evaluators do not have to infer it from scans. Add an attachment reference to every matrix row.
Variant identity: bind the document to the installed handle or knob
Evidence can cover a tested product family without identifying every configuration offered. Procurement should determine whether the evidence follows the specific furniture through its finish, material, dimensions, mounting method and other distinguishing variables. The bidder should explain any variation rather than leave the evaluator to infer it.
| Submission description | Qualification treatment | Required clarification |
|---|---|---|
| Family brochure with no test-report sample reference | Not sufficient to close the line | Which document tests this family, and which sample represents the offer? |
| Report for a named sample | Review the sample-to-offer mapping | What evidence links the sample to the offered variant? |
| Certificate listing the ordered reference and covered options | Review scope, number and validity | Are all offered options expressly included? |
For retrofit projects, the site condition becomes part of this identity exercise. A compatible lock body does not establish that the handle or knob fits the existing door, rose, spindle or other hardware arrangement. Use the door evidence collected through Smart Lock Retrofit Site Survey and reconcile it with the tender component schedule.
Where a drawing, dimension or product description drives procurement acceptance, confirm on the dated product page for the specific SKU and cross-check it against the evidence matrix. A tender line should say which record prevails if the drawing and the supplied product page differ, rather than leaving the bidder to decide after award.
Edition, class and grade: transcribe rather than interpret
Use the current edition of EN 1906 or the edition expressly named in the project contract, and route clause-level requirements to the published standard text. The evidence should state the edition used for testing or attestation. “Latest” is not an acceptable substitute in a bid schedule because it leaves the reference point open to change.
Class and grade information must also be transcribed with its source. If the report contains a classification, record the exact wording and the section of the published standard that defines it. If the tender brief sets a minimum furniture classification, show the comparison. If it does not, do not manufacture a grade requirement after bids arrive.
| Bidder statement | Procurement treatment |
|---|---|
| “Tested to the latest EN 1906” | Request the exact edition and published title |
| “EN 1906 Grade stated in report” | Transcribe the designation and definition; verify against the standard text |
| “The smart lock is EN 1906 rated” | Rewrite as furniture evidence for the identified handle or knob |
| “Equivalent standard tested” | Request the scope, test methods and equivalence reasoning for formal review |
The EN 1906 class and grade decode used by the buyer should remain separate from a classification for the lock body, radio, fire door or access-control system. One component’s result cannot be used to rate the rest of the assembly. For a more detailed reading method, see Clause Bank: Decoding EN 1906 Class and Grade Numbers for Door Hardware.
Document authentication: verify before a bidder passes
A complete-looking PDF can still be incomplete, superseded, outside scope or unrelated to the product offered. Authentication is a qualification step, not an administrative formality.
| Verification action | Evidence sought | Issue to record |
|---|---|---|
| Identify the issuer | Full issuing body name and role | Unclear issuer or unclear status |
| Match the number | Report, certificate or declaration identifier | Number absent or not searchable |
| Check issue data | Issue date, revision and stated validity | Missing, inconsistent or superseded record |
| Confirm scope | Product and configuration references | Offered item outside stated scope |
| Validate the source | Issuer contact, database entry or traceable original | Copy cannot be connected to the issuer |
| Trace the sample | Description linking test evidence to product reference | Sample identity cannot be established |
| Record exceptions | Deviation, limitation or exclusion wording | Result is conditional and not disclosed |
Use Reading an EN 1906 Test Report Page by Page: A Smart Lock Buyer Walkthrough when the bidder’s report needs a structured review. The tender file should contain the reviewer’s conclusion, the reason and the evidence examined. Avoid an unexplained “verified” status.
Where verification cannot be completed before award, make it an explicit condition of qualification and identify the party responsible for closure. A provisional status is acceptable only when the contract records what remains open, what evidence will resolve it and which decision will be blocked until closure.
Draft tender clause and compliance wording
The clause should describe evidence and traceability without converting a furniture test into an approval of the complete smart lock. Draft the following language for project-specific review:
EN 1906 evidence for lever handles and knobs: For each furniture line, the bidder shall provide evidence identifying the offered product, the tested sample, the current edition of EN 1906 or the edition specified by the contract, the test or attestation result, any exceptions, the document number, issue date, scope and verification route. The bidder shall distinguish test reports, certificates, declarations of conformity and product or label markings.
Scope limitation: EN 1906 evidence shall be applied only to the lever handle or knob to which it relates. It shall not be offered as the sole evidence for lock-mechanism operation, radio characteristics, electromagnetic behaviour, emergency escape, fire-door performance, credential handling or complete-door assembly performance.
Traceability: Where the document refers to a product family or sample, the bidder shall explain the relationship between the tested sample and every offered variant. Marketing statements and unattributed images shall not be submitted as substitutes for the requested evidence.
Clarification: An incomplete response shall identify the missing field, explain the reason and state whether a document can be supplied before the stated clarification cut-off. Material ambiguity shall be resolved through the tender process and recorded in the evaluation file.
Change control: Any replacement furniture, modified fixing arrangement, different finish, revised test sample or material change that could affect the submitted evidence shall be disclosed. The bidder shall identify the evidence required to preserve qualification for the changed item.
This wording gives evaluators a consistent compliance test while preserving the scope distinction. It also avoids a common procurement error: accepting “equivalent” evidence without defining who determines equivalence, against which published scope and using which test methods.
CONFIRM-WITH-LOCAL-COUNSEL: Review the final tender instruction, acceptance rule and contractual consequence against the governing procurement rules and project jurisdiction before issue.
Clarification schedule for incomplete or ambiguous submissions
Issue clarification questions in a numbered schedule so responses can be linked back to matrix rows. Combine questions that apply to several lines only when the required answer remains identical.
| Question | Reason for the question |
|---|---|
| Which document is being submitted: report, certificate, declaration or marking? | Prevent records from being treated as equivalent |
| What is the full document number, revision and issue date? | Establish document identity |
| Which edition and published title does the document use? | Fix the technical reference |
| Which sample was tested and how does it match the offered item? | Establish variant traceability |
| What does the certificate or declaration expressly cover? | Read the real scope |
| What result and classification wording are stated? | Record the finding accurately |
| Are there exceptions, deviations or limitations? | Expose conditional evidence |
| How can the issuer or number be verified? | Test document authenticity |
| Which production controls connect the evidence to supplied items? | Address ongoing supply risk |
| Which separate evidence covers the lock body and other functions? | Preserve scope boundaries |
| Which party owns each outstanding evidence action? | Make closure accountable |
Tell bidders to answer with a document reference, page or section where possible. A narrative answer without an attachment is weaker evidence than a short matrix row with a precise citation. If the answer changes an earlier submission, require a clearly marked revised response and preserve both versions in the clarification record.
Do not use clarification to redesign the tender after opening bids. If a new requirement emerges, determine whether it is a clarification of existing wording or a substantive change. Record that decision consistently for every bidder.
Evaluation method: pass, condition or reject
Qualification should be evidence-led. Evaluate the mandatory scope and identity checks first, then apply the threshold stated in the tender instructions. Commercial scoring should not compensate for missing technical evidence.
| Evaluation criterion | Pass | Conditional | Fail |
|---|---|---|---|
| Scope fit | Furniture line is clearly within the intended EN 1906 scope | Scope explanation needs clarification | Evidence is offered as proof of unrelated lock or door functions |
| Document identity | Type, number, issue data and source are identified | Source verification remains open | Type or issuer cannot be established |
| Variant traceability | Sample or certificate expressly connects to the offer | Mapping can be completed from a defined record | No defensible link to the offered item |
| Result and exceptions | Result and limitations are fully recorded | Closure is assigned and permitted by the tender | Material deviation is concealed or the result is absent |
| Exact coverage | Scope covers the ordered reference and options | Coverage clarification is outstanding | Ordered item is outside the stated scope |
| Evidence quality | Threshold in the instructions is met | Provisional status is contractually managed | Threshold is not met |
| Production continuity | Relevant controls are supplied | Defined evidence is due as a condition | No basis to connect qualified evidence to supply |
Record each outcome against the bid line, not merely against the bidder as a whole. One weak component should not disqualify an otherwise supported furniture line, and a strong certificate for one component should not rescue an unsupported line elsewhere.
Readers comparing approaches usually start with smart lock installer certification considerations. That is the same question en 1906 smart lock tender evidence has to answer here.Before evaluating, agree on how a conditional response will be handled. A condition is meaningful only when it names the outstanding evidence, responsible party, closure point and decision consequence. During clarification, avoid shifting the required evidence level merely because a bidder found stronger evidence than another bidder submitted.
This overlaps with the earlier coverage in the smart lock ansi mortise. That is the same question en 1906 smart lock tender evidence has to answer here.
Award conditions and production-control evidence
A qualification record can become stale between bid submission and manufacture. The contract should preserve the link between the accepted evidence and the goods actually supplied.
| Change event | Evidence action before acceptance |
|---|---|
| Ordered reference changes | Compare the replacement against the accepted scope and sample linkage |
| Finish or visible configuration changes | Confirm that the variation remains within the qualified evidence |
| Fixing arrangement changes | Review the product record and any applicable test evidence |
| Manufacturer or production source changes | Obtain the relevant production-control evidence |
| Document is reissued or superseded | Replace the obsolete record and check for changes |
| Test report is replaced by a certificate | Reassess the document type and coverage |
| Furniture is omitted from the final order | Update the evidence matrix and commercial schedule |
Where the production-control evidence demonstrates how the qualified design remains controlled, retain it with the award file. Where only a generic quality-management statement is available, record that limitation; an organisation-management certificate does not prove conformity of a particular SKU.
CONFIRM-WITH-LOCAL-MARKET-ACCESS-TEAM: Confirm any destination-market document, declaration or marking required for the exact offer and verify which authority signs it off before release.
Bidder response sheet and submission index
The bidder response sheet should compress the completed matrix into a signed document. Attach the underlying evidence, preserve references in the index and use the same file names in both records.
| Submission index | Required content | Bidder status |
|---|---|---|
| 00 | Cover sheet and signed response summary | Submitted / qualified / clarification |
| 01 | Tender instruction and component schedule | Submitted / qualified |
| 02 | EN 1906 evidence matrix | Submitted / qualified |
| 03 | Test report or explanation of availability | Submitted / qualified |
| 04 | Certificate, including scope and number | Submitted / qualified |
| 05 | Declaration of conformity, if offered | Submitted / qualified |
| 06 | Marking evidence and explanation | Submitted / qualified |
| 07 | Sample-to-variant traceability | Submitted / qualified |
| 08 | Production-control evidence | Submitted / qualified |
| 09 | Clarifications and replacement documents | Open / closed |
| 10 | Signatory confirmation and contact | Submitted |
A suitable signatory statement is: “The bidder confirms that the response identifies the documents supplied for each lever handle and knob, distinguishes those documents from evidence for other product functions, and discloses the scope, result, exceptions, traceability and verification route stated in the matrix.”
Attach the document authorising the signatory to make the response, or follow the tender’s authority requirements. Do not let a sales catalogue become the contractual response merely because it contains the phrase EN 1906.
Qualify the bid on what can be demonstrated, not on the presence of a familiar mark or a broad family statement. The evidence checklist succeeds when each line shows what was tested, which sample represented the offer, what the named record says, how it was checked and what remains outside its scope. That record gives procurement a defensible basis for comparison without confusing furniture evidence with approval of the complete smart lock.
Put the answer on paper and request a quote against that document.

