Or Equal Substitution in Retrofit Projects
In or equal substitution retrofit projects, the proposed lock must be tested against the existing door set, not against a catalogue photograph. The review asks whether the candidate preserves the scheduled fit, function, evidence, and approval trail without transferring an unrecorded risk to the installer, client, or operating team.
Direct answer. To put it plainly: or equal substitution retrofit projects has to hold for or equal substitution retrofit projects. or-equal-substitution has to hold at the same time. The sections below describe the order or equal substitution retrofit projects is settled in. An or equal substitution retrofit projects is a tool pack for the specifying side. or equal substitution retrofit projects names the artefact the RFQ must produce for or equal substitution retrofit projects.
An or-equal request is a request to substitute; it is not approval. The specifier determines equivalence against the issued criteria and records the reasons. This handbook converts that responsibility into twelve clauses for a retrofit-focused product substitution review. Begin with a door-specific Smart Lock Retrofit Site Survey, then require the candidate supplier to return one dated package that can be evaluated without a meeting.
Clause 1: Define What May Be Proposed
Use the or equal clause to distinguish a proposed substitution from an unauthorized product change. It should identify the approved baseline, the affected door identifiers, the candidate product, the proposed supplier, and any stated differences. A request may include an alternative only after the requester acknowledges that the candidate is being compared with the specified door set rather than accepted on its description. The build options sit in the smart door locks.
A workable clause reads as follows:
A request to substitute shall identify the approved baseline and drawing revision, each affected door identifier, the candidate product, and every functional or dimensional difference known by the requester. The specifier shall evaluate the candidate against the approved door-set requirements and issue a recorded determination. Submission of a request, receipt of literature, or a successful shipment does not constitute approval.
This wording makes retrofit lock substitution a controlled request instead of an informal suggestion. It also establishes that the installer may identify a workable candidate but does not decide equivalence. The supplier supplies evidence, the specifier evaluates it, and any separate approval authority named by the project remains responsible for its own scope.
CONFIRM-WITH-LOCAL-COUNSEL: Confirm the contract definition of an equal product and the persons or entities authorized to approve a deviation for this project and jurisdiction.
Clause 2: Freeze the Baseline by Door Identity
Every request must point to a frozen baseline. For a retrofit, the baseline is the combination of the approved product requirements, the recorded dimensions of the door on site, the door’s function, and the interfaces it must preserve. It is not the product shown in a current catalogue and not a typical plan detail that was never coordinated with the existing frame.
| Baseline element | Required record | Review purpose |
|---|---|---|
| Door identity | Door schedule identifier, drawing revision, and physical location | Prevents the candidate from being approved for the wrong door |
| Existing conditions | Dated dimensional survey and relevant site photographs | Makes clear that the comparison uses the installed condition |
| Door-set function | Locking arrangement, egress role, access method, monitoring duty, and power expectation | Defines the outcomes the substitute must preserve |
| Interfaces | Frame, faceplate, strike, adjacent hardware, and service-clearance requirements | Identifies physical dependencies outside the lock |
| Finish and identification | Colour reference, hardware marks, labels, and visual requirements | Prevents an approved function from being paired with the wrong appearance |
The door set is the door leaf, frame, hardware, and locks considered as one assembly. Its egress route and locking arrangement are part of that assembly. The clause should also say which record controls when the approved schedule, a later drawing revision, and the field survey differ. That instruction is essential because the retrofit condition may have moved beyond the original design record.
A photograph supports identification, but a photograph shows the finish; it does not specify it. Likewise, a survey is evidence of a measured condition, not permission to change the specified product. Keep the baseline document revision attached to the request so every later comparison points to the same starting point.
Clause 3: Make Retrofit Compatibility the First Gate
The first gate is physical compatibility. The candidate must be checked against the door that will receive it, including the existing frame and adjoining hardware. A dimensional drawing can establish only the dimensions it actually identifies. It cannot stand in for the field condition, and the approved catalogue drawing cannot replace a door-specific measurement.
The dimension the installer needs is an as-measured backset, stated in the format door identifier, value, unit, measurement method, and date. Backset is the distance from the door edge to the centre of the spindle or cylinder. Bore diameter and bolt-to-bore distance are separate dimensions, not interchangeable labels. A package that omits either bore dimension cannot be checked reliably.
| Fit check | Information the package must state | Reviewer’s question |
|---|---|---|
| Door thickness | Actual leaf thickness and measurement location | Can the candidate case and fixing arrangement enter the door as found? |
| Backset | As-measured value and drawing reference | Does the spindle or cylinder align with the existing preparation? |
| Bore diameter | Each relevant bore and its function | Will the proposed spindle, fixing, or cylinder arrangement pass through the prepared opening? |
| Bolt-to-bore distance | Separately identified value | Does the hardware position match the door’s actual drilling? |
| Spindle and fixing positions | Hole sizes, centres, and any projections | Can installation proceed without enlarging the door or changing the frame? |
| Faceplate and strike | Dimensions, fixing centres, and edge relationship | Will the closing-edge components form a matched pair? |
| Handing and swing | Door handing, swing direction, and any pull side | Is the candidate prepared for the actual door rather than the planned handing? |
| Adjacent clearances | Lever, cylinder, frame, and neighbouring hardware clearances | Can the lock operate without fouling another component? |
| Service route | Access needed for fitting, adjustment, power, and future service | Is enough room retained for the intended maintenance method? |
The candidate should state its dimensions on a dated drawing or technical data source. For every specification that drives procurement, confirm on the dated product page for the specific SKU, and request the underlying document behind the summary. A sample or mock-up may evidence fit and finish, but it does not establish operating performance.
Retrofit compatibility therefore means more than sharing a product family. It means that the proposed preparation, installation route, interfaces, and service access can be reconciled with the recorded door condition without an unresolved assumption.
Clause 4: Compare Function Through Outcomes
A candidate may use a different internal implementation and still preserve the scheduled outcome. The product substitution review must state the outcome rather than accepting a feature label. Start with the approved baseline, identify the candidate’s documented behavior, and then ask whether the difference would alter access, locking, monitoring, local operation, or the information received by another system.
| Functional area | Baseline question | Evidence to compare | Consequence of a gap |
|---|---|---|---|
| Credential behavior | Who may operate the lock and what event is recorded? | Current requirement, dated candidate documentation, and configuration record | An unrecorded change to access or audit expectations |
| Locking arrangement | Which points lock, in what order, and from which side? | Locking schedule and candidate operating description | A change to the door’s security function or operation |
| Monitoring duty | Is the open, closed, forced, or other event required, and where is it received? | Interface description and approved integration record | A gap between physical events and downstream information |
| Local operation | Must the lock work when a network or controller is unavailable? | Written operating behavior for the candidate configuration | Dependence on a service condition not present in the baseline |
| Power arrangement | What is the intended power source, backup arrangement, and change method? | Dated product documentation and site coordination record | A lock that cannot be maintained or operated as scheduled |
| Service and configuration | Who can adjust, update, or return the lock to a defined state? | Configuration and handover requirements | Uncontrolled change after approval |
The review should distinguish an equivalent result from a different way of obtaining that result. Different technology may be acceptable if the required result, failure behavior, records, and maintenance route remain aligned. It is not enough to say that the candidate performs the same function in general.
Keep any client assumption about the life of the installation labelled as a client assumption. It should not be converted into a supplier claim during the review. Likewise, the candidate’s feature summary should not be used as proof of an installed result.
Clause 5: Protect the Existing Door Set and Escape Route
The lock cannot be detached from the door’s role. For a mortise installation, the lock case sits within the door; for a rim installation, the case is mounted to the surface; and a multipoint arrangement operates several locking points through one gear. The proposed candidate must preserve the relationship between that operating arrangement, the faceplate, the strike, the door leaf, and the frame.
The review must also identify whether the door forms part of an egress route. Panic hardware releases the door on the escape route, while free egress describes operation without special knowledge. A request must not alter the relationship between the lock and that hardware through an unrecorded configuration or installation change.
Fail-safe and fail-secure are not product labels that the reviewer selects in isolation. They describe the intended state on power loss, and that state must be decided by the door’s role. The substitution package should identify the proposed arrangement, while the project’s approved door-set decision remains the control.
CONFIRM-WITH-LOCAL-BUILDING-CONTROL: Confirm which building-control review applies to the proposed hardware change and what evidence the reviewing authority requires for this project location.
CONFIRM-WITH-FIRE-AUTHORITY: Confirm whether the fire authority must review any change involving the door assembly, escape hardware, or locking arrangement before the candidate is accepted.
CONFIRM-WITH-ACCESS-CONSULTANT: Confirm the installed-door operating criteria and the person or authority responsible for signing off the accessibility review for the affected doors.
These confirmations identify decisions to obtain; they do not pre-empt the relevant authority. Record each response, its scope, its date, and the person who supplied it.
Clause 6: Require Evidence Named by Document, Scope, and Holder
A door hardware submittal is useful only when a reviewer can inspect the evidence without asking what it means. Each material claim should point to a named document, the scope it covers, its revision or date, and the holder of the original. “Approved,” “tested,” or “meets the project requirement” is not a substitute for that information.
| Evidence item | What it can establish | What it cannot establish by itself |
|---|---|---|
| Dated product-page extract | The supplier’s published description for the identified SKU at a stated date | Fit to the door, installed operation, or an authority’s decision |
| Dimensional drawing | The dimensions and interfaces stated by the manufacturer | The dimensions actually found on site |
| Installation manual | The manufacturer’s intended fitting and service method | Proof that the installer followed those steps |
| Test or evaluation report | The result within the report’s stated scope and conditions | A result for a different SKU, configuration, door, or installation |
| Site survey | The measured condition and visible features of the identified door | Approval of a substitute product |
| Physical sample record | The characteristics observed on the sample presented | Complete performance of a production installation |
| Authority correspondence | The decision made within the authority’s stated scope | Approval of matters outside that scope |
The Or Equal Substitution: Documents a Specifier Should Demand resource provides a useful starting point for the request list. For this retrofit application, the reviewer should reject a package that contains only general literature. A product brochure without dimensions, a catalogue page without the identified SKU, and a verbal assurance of fit should each be treated as missing evidence.
The door hardware submittal is not approved until the review is recorded and dated. That record should identify the documents actually examined, not merely the document categories expected. A sample can establish selected fit and finish characteristics; it cannot establish the complete operating result.
Clause 7: Allocate the Authority Before the Comparison
The decision belongs to the specifier when the question is whether the candidate is equal to the issued requirement. That decision must be supported by evidence and coordinated with other approvals. It should not be transferred informally to the installer, supplier, or an individual reviewer who happens to attend the meeting.
| Decision | Required input | Decision owner | Record required |
|---|---|---|---|
| Equivalence against the written baseline | Complete door hardware submittal and comparison matrix | Specifier or named design authority | Dated determination with reasons |
| Physical fit for the identified door | Field survey and candidate dimensions | Installer confirms feasibility; specifier records the comparison | Signed dimensional check |
| Contractual approval right | Confirmation from the client’s contracting representative | Authorized client approver | Approval or rejection linked to the request |
| Building-control question | Relevant project evidence and proposed change | The competent authority decides within its scope | Dated authority response |
| Fire or escape-hardware question | Approved door-set information and candidate evidence | The competent fire authority decides within its scope | Dated authority response |
| Accessibility question | Installed-door requirements and proposed operating behavior | The responsible access reviewer decides within its scope | Dated review outcome |
The clause must also prevent one approval from being reused beyond its scope. An installer’s confirmation that a candidate can be fitted does not decide equivalence. A specifier’s technical comparison does not replace an approval required from a separate authority. A supplier statement does not amend the baseline.
Use the Or Equal Substitution: Reviewer Checklist as a final allocation check, and name the actual decision owner in the project record. If the contract assigns approval elsewhere, reconcile that assignment with the design authority before requests are issued.
Clause 8: Run the Review as a Sequence of Controlled Gates
The product substitution review should follow a repeatable sequence. Its purpose is to prevent a commercially attractive candidate from advancing on an incomplete comparison and to identify the exact gate at which the request stops.
flowchart TD
A[Request received] --> B[Baseline tied to door identity]
B --> C[Retrofit compatibility checked]
C --> D[Function and door set checked]
D --> E[Authority questions resolved]
E --> F[Decision recorded and dated]
At the intake gate, the reviewer confirms that the request names the door, baseline revision, candidate, requester, and stated differences. Missing information returns the request as incomplete. It does not create an implied provisional approval.
At the evidence gate, the reviewer checks dimensions, operating documentation, interface information, and site records. The reviewer then compares the candidate’s stated outcome with each scheduled requirement. Any unresolved question is routed to the owner identified in the authority matrix.
This staged approach also distinguishes a new-construction review from a retrofit review. In Or Equal Substitution in New Construction, the baseline can be coordinated from a defined design set. In a retrofit, it must be reconciled with the existing door, measured condition, and interfaces already installed.
The Or Equal Substitution: A Smart Lock Specifier Guide offers a broader review sequence. For retrofit work, add the door-specific survey and require every conclusion to cite the exact door identifier to which it applies.
Clause 9: Verify Operation on the Identified Door
A desk comparison can establish what the documents say. It cannot establish how the approved combination behaves on the actual door. The clause should identify which checks require a physical mock-up, an installed-door test, a configuration record, or written confirmation from another party.
For the installed-door review, use a controlled sequence:
- Identify the door and configuration. Record the door identifier, candidate identification, installed hardware, and the configuration used for the test.
- Confirm fit and movement. Check the faceplate, strike, lever or cylinder alignment, door operation, and absence of interference with adjacent hardware.
- Exercise the scheduled access path. Use the intended credential or operating method and compare the event and access result with the baseline.
- Exercise the locking sequence. Confirm the locking points, operating order, and final locked condition against the approved door-set schedule.
- Check the monitored events. Confirm that the events required by the baseline are produced and received where the baseline requires monitoring.
- Check defined service conditions. Verify the agreed response to loss of network, controller, or power condition without inventing a behavior the candidate documentation has not established.
- Check the escape-route relationship. Observe the interaction between the lock and any panic hardware under the method agreed with the relevant authority.
- Record the result. Note the tester, date, door identifier, setup, result, anomaly, photographs where useful, and the disposition of each exception.
A physical sample evidences fit, not performance. It may be useful during the submittal stage, but it does not replace testing the installed combination where that verification is required.
Clause 10: Define the Decision Outcomes
A review should end in a defined state, not an ambiguous note such as “acceptable subject to review.” The following comparison gives the reviewer and requester the same meaning for each outcome.
| Outcome | Meaning | Required next action |
|---|---|---|
| Accepted as equal | The candidate meets every applicable requirement in the frozen baseline and no unresolved authority question remains | Issue the substitution approval record and update the controlled project documents |
| Accepted with conditions | The candidate may proceed only after named evidence or actions are completed at a defined gate | Assign each condition to an owner and prohibit the affected release or installation step until closure is recorded |
| Deferred for evidence | The proposal remains under review because a defined item of evidence is missing or contradictory | Return a precise request for the missing document, test, measurement, or response |
| Not accepted as equal | A stated requirement is not preserved, or the candidate requires a deviation that the decision owner rejects | Record the failed requirement, the reason, and whether a revised request is permitted |
| Accepted as a deviation | The proposal is intentionally different and is being approved outside the equal-product route | Use the project’s formal deviation process and do not label it as equal |
Conditions must be testable statements. “Confirm compatibility” is incomplete. “Provide the dimensional drawing that identifies the as-measured backset for door identifier D-14 and the installation instruction covering the existing strike” identifies the document, door, and closure evidence.
For or equal substitution retrofit projects, the accepted candidate remains linked to the reviewed baseline and door identifiers. Approval cannot be reused automatically at another door. If the request covers several doors, the record must show whether one comparison applies to all of them or whether each door required a separate fit and function check.
Clause 11: Preserve the Decision and Control Later Changes
The substitution approval record is the audit trail that explains what was requested, what was compared, what evidence was used, and who decided. It should contain the request identifier, baseline and drawing revisions, candidate identification, affected door identifiers, comparison matrix, evidence register, authority responses, decision, reasons, conditions, signatures, and dates.
A reason should identify the requirement preserved and the evidence relied upon. “Equivalent” is not a reason. “The candidate preserves the approved door dimensions and locking sequence shown in the dated comparison drawing” is reviewable. The record should also identify any difference that was expressly rejected or accepted as a deviation.
Readers comparing approaches usually start with smart lock factory audit checklist for international buyers. That is the same question or equal substitution retrofit projects has to answer here.Later changes can invalidate the comparison. Require a new review when a door is replaced or rehanged, a field dimension changes, the frame, faceplate, or strike is modified, the candidate SKU or configuration changes, the drawing revision changes the door’s role, or an access, power, monitoring, or authority requirement changes. The clause should identify who may declare the baseline frozen again and how affected approvals are withdrawn or reissued.
This overlaps with the earlier coverage in what questions should you ask a smart lock manufacturer. That is the same question or equal substitution retrofit projects has to answer here.At handover, give the client the approved substitution approval record together with the current as-built information and the relevant operating and maintenance instructions. Name the record custodian and the document location. The retained record must show which candidate was approved for which door, not merely that “an equivalent lock” was used.
Clause 12: Issue the Integrated Clause and Buyer Pack
The complete retrofit clause should connect the request, baseline, evidence, review, and record in one controlled instruction. A usable working template is:
Or-equal substitution request and determination
- The requester shall submit one request for each identified door set or clearly defined group of matching door sets. The request shall identify the approved baseline, drawing revision, survey revision, candidate product, proposed supplier, and every known difference.
- The requester shall submit dated dimensional information, operating documentation, interface information, and any evidence required by the approved baseline. General literature shall not replace door-specific data.
- The specifier shall determine whether the candidate preserves the approved retrofit compatibility, function, locking arrangement, monitoring duty, power expectation, and door-set interfaces.
- The determination shall obtain confirmation from every authority identified by the project for building-control, fire, escape-hardware, accessibility, or contractual matters within that authority’s scope.
- The outcome shall be stated as accepted as equal, accepted with conditions, deferred for evidence, not accepted as equal, or accepted as a deviation. Any condition shall name its evidence, owner, and closure gate.
- The decision shall be recorded in the substitution approval record. Approval for one door or baseline revision shall not be transferred to another without review.
- A change to the door, product, configuration, drawing revision, or governing requirement shall reopen the affected comparison before the changed work proceeds.
Before issuing the request, the buyer should assemble the following pack:
| Buyer action | Evidence or artifact | Owner | Close condition |
|---|---|---|---|
| Identify the affected door | Dated survey tied to the door schedule and drawing revision | Door hardware consultant | Every request points to a measured door |
| Freeze the baseline | Approved schedule, product requirement, and recorded interfaces | Design authority | Baseline revision is stated |
| Check retrofit compatibility | Side-by-side dimensional comparison and installation method | Consultant with installer input | No unresolved dimensional dependency |
| Compare operating outcomes | Completed functional comparison and evidence register | Specifier | Each scheduled requirement has a disposition |
| Resolve scoped questions | Written responses from the relevant authorities | Project authority coordinator | No open question remains within its scope |
| Record the determination | Signed decision with reasons and conditions | Named decision owner | Date, revision, and conditions are recorded |
| Control subsequent changes | Change register linked to the approved record | Project document controller | Affected approval is reissued before work proceeds |
When issuing the request, ask the candidate supplier to return one dated retrofit package tied to each door identifier. That package should let the office run the same product substitution review for every candidate, rather than relying on a catalogue page, an unqualified sample, or a verbal assurance of fit.
Put the answer on paper and request a quote against that document.

