United kingdom door thickness survey worksheet: use this UK door thickness and backset survey worksheet to capture hospitality door geometry, exceptions.

Δημοσιεύτηκε στις: Ιουλ 11, 2025

Door Thickness and Backset Variance in the United Kingdom: A Survey Worksheet

Door Thickness and Backset Variance in the United Kingdom: A Survey Worksheet

The united kingdom door thickness survey worksheet is a measurement record for individual hospitality openings, not a nominal door schedule. Record the front, kitchen, store, terrace, toilet corridor or cellar separately where each is in scope. Ask what is physically at the opening before asking whether a lock will fit. Thickness, backset, face width, handing and existing hardware affect installation. The memo turns those observations into a sample-test release decision while preserving the manual route for the front and kitchen doors.

Direct answer. To put it plainly: united kingdom door thickness survey worksheet has to hold for united kingdom door thickness survey worksheet. ukca-ce has to hold at the same time. The sections below describe the order united kingdom door thickness survey worksheet is settled in. An united kingdom door thickness survey worksheet defines entry conditions for one market. united kingdom door thickness survey worksheet starts the approval conversation. Every united kingdom door thickness survey worksheet condition names its evidence.

Decision carried by this memo The next step is to [request

To: Brand ownerSubject: Door geometry variance for a hospitality lock shortlistDecision requested: Release only traceable openings to controlled sample fit

Use this memo as brand owners move from awareness to supplier evaluation. Decide which openings may proceed to a controlled sample fit and which require remeasurement, revised hardware or exclusion. A release note must identify the door record, candidate SKU and evidence used. “Fits UK doors” is not a fit record. Against the catalogue, start from the smart door locks.

Variance that changes the selection

Treat thickness and backset as measured ranges, not catalogue labels. UK door thickness measurement should show minimum and maximum leaf thickness because one reading can conceal variation. For UK lock backset measurement, name the edge and centreline used: a number measured from different features is not comparable. Record mortice lock backset, Euro cylinder backset or multipoint geometry as separate types. Where a timber flush door inspection is planned, add edge condition and signs of movement. A hospitality door survey that mixes door types, units or datums cannot support a defensible shortlist.

For the wider replacement sequence, use Licensed Hospitality Lock Replacement Programmes in the United Kingdom: Survey Before You Order to connect geometry exceptions with the planned door-by-door rollout.

Fields for the door hardware evidence pack

Complete one united kingdom door thickness survey worksheet line for each opening under consideration.

FieldRequired entryDecision use
Record IDUnique code, location and photo referencesTrace every decision
Door useFront, kitchen, store, terrace or service useConnect access and manual route
LeafMaterial, core, panel and rebateIdentify construction constraints
ThicknessMinimum, maximum and measurement positionsCompare the observed range
BacksetValue, edge datum and measured featureMake geometry comparable
Face and edgeFace width, rebate depth and clearancesCheck case and keep relationship
HandingLeft or right from the named facePrevent orientation errors
Existing hardwareLock, cylinder, keep, handles and closerIdentify removal and interaction
Door statusAny declared fire or escape functionTrigger the required local review
Candidate evidenceDated drawing, product page and fit methodSupport or withhold release

Treat every blank as an evidence gap. Use “not measured” with a reason rather than inserting a guessed value. Record units, measurement date and observer. A nominal schedule value may appear in the source-document field, but it cannot replace the observed range.

Measurement route and stop point

Use one method for every door and retain photographs that show the measurement context.

  1. Name the observation face, closing edge, swing direction and units before taking readings.
  2. Measure leaf thickness at the latch edge and two additional positions without forcing the tool against the leaf. Record the minimum and maximum.
  3. Use the candidate drawing to identify the backset datum. Record the centreline and the feature measured, not only the number.
  4. Capture face width, rebate depth, hinge and latch clearances, handing, glazing positions and obstructions.
flowchart TD
A[Create one record per opening] --> B[Measure the thickness range]
A --> C[Record the backset and datum]
B --> D[Check face, edge and handing]
C --> D
D --> E[Compare with dated evidence]
E --> F{All critical fields aligned}
F --> G[Release a controlled sample fit]
F --> H[Hold and close the evidence gap]

Stop the release when the candidate cannot be mapped to the observed geometry. An installer should review the method before ordering; the commissioning sequence in Training Installation Teams in the United Kingdom on Smart Lock Commissioning for Timber Flush Doors and Euro Cylinders provides a separate handover reference.

Opening-level release table

Apply the same release conditions to every hospitality opening, including the kitchen door that carries frequent service traffic.

OutcomeEvidence conditionAction
ProceedEvery critical dimension and datum maps to dated candidate evidenceIssue a door-specific sample-fit reference
HoldA measurement, datum, manual route or document is missingRe-survey or request evidence before ordering
Revise or excludeCandidate evidence cannot cover the observed geometryChange the hardware or remove the opening from scope

Also record the manual route for the front and kitchen doors. Fit evidence answers whether hardware can be installed; it does not establish how staff will enter if electronic access is unavailable during a service change.

For related site formats, use the published Office Smart Lock Site Survey and Smart Lock Retrofit Site Survey as adjacent templates without merging their measurement conventions.

Evidence pack and document trail

Create a door hardware evidence pack containing the photograph set, measured worksheet, dated product-page extract, dimensional drawing, installation instructions, door-set drawing and any assembly evidence supplied for the exact SKU. For each candidate, confirm on the dated product page for the specific SKU the dimensions, permitted range and installation constraints. Do not transfer a drawing from another model.

Index the supplied documents under ukca-ce as a retrieval route rather than an acceptance decision. Ask the supplier which documents apply to the exact product and revision. Reading UKCA and CE Documents for Smart Locks: A Buyer Guide for the United Kingdom expands that document check. Retain united-kingdom in the project metadata so later revisions remain tied to the correct geography and evidence set.

CONFIRM-WITH-LOCAL-AUTHORITY: Confirm with the relevant local authority, door-set supplier and responsible fire-safety professional which approvals, assembly evidence and manual-egress arrangements apply to each opening. Do not treat this worksheet as compliance approval.

Handover for controlled sample testing

Ask shortlisted suppliers to return one completed worksheet line for every candidate-door pairing, with the drawing revision shown. The brand owner should sign the exception list before samples are ordered. The installer should remeasure the actual opening and update the record before drilling.

Readers comparing approaches usually start with smart lock bulk order process. That is the same question united kingdom door thickness survey worksheet has to answer here.Changes to the leaf, rebate, cylinder arrangement, handing or intended lock family return that opening to the evidence check. The role split and approval record should follow Specifying Smart Locks for Licensed Hospitality Projects in the United Kingdom. Release a sample only when its evidence identifies the surveyed door, the named candidate and the unresolved conditions that still require local confirmation.

Once the requirement is written down, request a quote is the move.

Το καλάθι σας
Η εμπειρία σας σε αυτόν τον ιστότοπο θα βελτιωθεί με την ενεργοποίηση των cookies Πολιτική cookies
Chat on WhatsApp