Will SLK-9936S Fit Your Door? A Fit and Preparation Guide
Procurement teams can use these slk 9936s door fit notes to turn a catalogue entry into a documented site decision. The supplied first-party record lists an SLK-9936S door thickness range of 36–100 mm and identifies hotel wooden and metal doors as applicable types. It also identifies a 5-pin profile mortise and a 3-point latch. Before any of those fields becomes a purchase-order instruction, confirm on the dated product page for the specific SKU and obtain current drawings.
Direct answer. In short, slk 9936s door fit notes is the subject of this piece. slk 9936s door fit notes is where the work on slk 9936s door fit notes sits. slk-9936s is what has to be evidenced before anyone signs. A slk 9936s door fit notes is a component-level look at how the technology behaves. slk 9936s door fit notes is where the limits sit. slk 9936s door fit notes is verified on the dated product page.
Throughout, slk 9936s door fit notes means what slk 9936s door fit notes sets out. It is a working definition of slk 9936s door fit notes drawn from the evidence below. It is valid for the specific market and product, not as a general claim.
- Test what it does — confirm on the dated product page for the specific SKU behind slk 9936s door fit notes
- Test where it stops — record where the technology in slk-9936s stops working
- Plan the manual path — name the mechanical path that remains if slk 9936s door fit notes fails
- This is the sequence slk 9936s door fit notes has to follow, anchored on slk 9936s.
The answer is therefore conditional rather than visual. A door may fall within the published thickness range and still require work if its face area, backset, handing, mortise, frame rebate, or latch arrangement differs from the lock. Use the Office Smart Lock Site Survey to collect opening-level evidence, then apply the gates in this guide before treating the SLK-9936S as a confirmed fit.
The Fit Verdict: A Conditional Yes
The strongest fit case is a hotel wooden or metal door within the listed thickness range, with a prepared mortise and an opening arrangement that the current SLK-9936S drawings can validate. A weaker case involves relying on visual similarity, an unverified existing mortise, or an adapted frame that has not been reviewed.
| Evaluation point | First-party position | Procurement meaning |
|---|---|---|
| Door thickness | 36–100 mm listed | Confirm the measured leaf and current SKU record |
| Door material | Hotel wooden and metal doors listed | Confirm the material and construction of the actual opening |
| Cylinder and mortise | 5-pin profile cylinder recorded | Request the mortise, faceplate, and cylinder drawings |
| Latch | 3-point latch recorded | Check the door and keeper for compatible geometry |
| Panel and backset | Not stated in the supplied record | Do not infer fit from the thickness range alone |
| Handing and swing | Not stated in the supplied record | Confirm before releasing the preparation drawing |
| Final decision | Conditional on current evidence | Approve, hold for information, or move to another route |
flowchart TD
A[Fit verdict and record limits] --> B[Measure door leaf]
B --> C[Route door by material]
C --> D[Test mortise cylinder and latch]
D --> E[Compare preparation routes]
E --> F[Check frame swing and hardware]
F --> G[Complete preparation checklist]
G --> H[Request current drawings]
H --> I[Apply fit decision matrix]
I -->|Approved| J[Release order and preparation work]
I -->|Conditional or hold| K[Assign evidence owner and due date]
K --> H
J --> L[Verify prepared geometry at installation]
Every specification in this comparison must be confirmed on the dated product page for the specific SKU. The practical verdict is “possible fit” when the basic gates pass, but “unverified fit” until the current dimensional evidence and preparation requirements are attached to the project record.
What the Supplied Record Does and Does Not Settle
The supplied SLK-9936S record is useful for defining the investigation, but it is not a substitute for a site-specific drawing set. In particular, the SLK-9936S door thickness range establishes one important boundary; it does not establish panel width, backset, spindle position, handing, or the shape of the latch and keeper.
| Record item | What it settles | What still requires confirmation |
|---|---|---|
| Applicable thickness of 36–100 mm | The measured leaf must pass this first gate | Whether every leaf area remains within the range |
| Hotel wooden and metal doors | The named door categories for evaluation | Whether the actual construction and face details match |
| 5-pin profile mortise cylinder | The cylinder format to inspect | Cylinder dimensions, centre position, and faceplate arrangement |
| 3-point latch | Latch geometry requires early checking | Throw, keeper position, active dimensions, and door-edge clearance |
| Stainless steel and alloy body | The lock body material recorded for the SKU | No inference about door material or environmental suitability |
| Documentation available on request | Drawings, guide, and datasheet can be requested | The exact content and revision of the material supplied |
| Configuration services | Project-specific logo, finish, packaging, and manuals may be discussed | Configuration scope must be confirmed in writing |
The missing dimensions are not obstacles if they are treated as open procurement items. They become expensive when the lock is selected first and the door is adjusted later.
Measure the Door Leaf Before Comparing Lock Geometry
Thickness at the lock position
Measure the closed leaf at the lock position and at points away from hinges and hardware. A single reading can be misleading when a door is tapered, has a stile near the edge, or contains a structural member beneath the skin.
Do not add an invented installation tolerance to the published range. If the smallest reading is close to either boundary, request the current dimensional drawing and disclose the measured condition rather than relying on a project assumption.
Face area and hardware positions
Measure the distance from the door edge to the spindle or cylinder centre, the faceplate position, and the available width and height around the intended escutcheon. Also record the position of any existing lever, reader, closer plate, inspection plate, or signage panel. These coordinates become a scaled preparation drawing rather than a list of disconnected measurements.
Handing and swing direction
Record the hinge side, opening direction, and whether the door swings toward or away from the corridor or work area. These facts affect access, latch engagement, escape arrangements, and potentially the lock orientation. The supplied record does not state handing, so the site survey should capture it independently.
| Measurement record | Preferred notation | Decision use |
|---|---|---|
| Leaf thickness | Reading at lock position plus auxiliary readings | Checks the 36–100 mm gate |
| Face layout | Edge-to-centre and centre-to-centre dimensions | Locates mortise and panel preparation |
| Existing faceplate | Width, height, and fixing positions | Tests whether an existing opening can be reused |
| Hinge and swing | Hinge side and opening direction | Confirms handing and operating space |
| Interferences | Coordinates of existing hardware | Prevents a paper-only fit decision |
A scaled face drawing made from these measurements is more useful than a photograph. Photographs can show general condition, but they cannot reliably communicate backset, centre positions, or edge clearances.
Route the Door by Material and Construction
The applicable categories of hotel wooden and metal doors establish where the fit review can begin. They do not remove the need to inspect construction, existing cutouts, and the surrounding frame. Doors with the same visible face can conceal different cores, edge buildup, or embedded reinforcements.
| Door construction | Position in the supplied record | Preparation focus | Provisional route |
|---|---|---|---|
| Hotel wooden door | Applicable type named | Core condition, edge thickness, existing mortise, panel area | Continue to dimensional validation |
| Hotel metal door | Applicable type named | Face construction, edge profile, cutout condition, keeper alignment | Continue to dimensional validation |
| Glass door | Not named as an applicable type | Any proposed patch fitting, drilling method, and frame interface | Hold for separate evidence |
| Aluminium or composite door | Not named as an applicable type | Wall thickness, extrusion geometry, insert locations, and fixing method | Hold for separate evidence |
| Mixed or uncertain construction | Not established by a material label | Core sampling or construction drawings before ordering | Hold the fit decision |
For the listed wood and metal categories, ask the manufacturer to confirm the current preparation drawing. For an unlisted construction, absence from the record is not a basis for inventing a special adapter or declaring the lock impossible. It means the proposed route needs evidence from the relevant product and door suppliers.
The phrase “RFID hotel card door lock” describes the credential platform, not the door-preparation method. A working credential reader can coexist with unsuitable geometry.
Test the Mortise, Cylinder, and Latch Interface
The supplied record names a 5-pin mortise cylinder and a 3-point latch. Those are the correct starting points for an interface review, but naming a component does not provide the dimensions needed to reuse an existing opening.
| Interface | Evidence to collect | Fit test | Hold trigger |
|---|---|---|---|
| Mortise case | Case dimensions, centre position, fixing points, faceplate outline | Existing case matches the current drawing | Any dimension or fixing position is unknown |
| Cylinder and collar | Bore size, centre position, collar shape, key orientation | Current cylinder arrangement is shown to match | Existing bore is obscured or nonstandard |
| Faceplate and keeper | Plate dimensions, edge position, keeper location and fixing | Latch enters the keeper without interference | Plate or keeper movement is unexplained |
| 3-point latch | Active latch geometry and operating direction | Door edge and frame can accommodate the mechanism | One latch point conflicts with the edge or frame |
| Escutcheon opening | Width, height, and available flat face | Panel can sit without forcing the door | Face has insufficient usable area |
| Mechanical override access | Route through the selected door and hardware | Emergency access can operate as intended | Access is blocked by an existing component |
A retrofit mortise may appear usable because the door edge and faceplate look alike. Replace that visual judgement with a measured comparison against the current manufacturer drawing.
If the existing hardware differs from the new lock, assess three separate questions: whether the opening can be modified, whether the frame and keeper can remain unchanged, and who is responsible for the resulting work. A possible physical modification is not the same as an approved preparation method.
Compare Replacement, Retrofit, and New-Door Routes
The SLK-9936S fit decision becomes clearer when the project compares preparation routes rather than treating “replacement” as one option. Each route has a different evidence burden and a different point at which cost and schedule consequences arise.
| Route | Best-fit condition | Evidence required | Main risk | Procurement decision |
|---|---|---|---|---|
| Prepared-door replacement | Existing mortise, faceplate, and keeper match the current drawings | Full dimensional comparison and site measurements | A partial visual match is mistaken for compatibility | Approve only after interface validation |
| Controlled retrofit | The opening can be prepared to an issued drawing | Confirmed work method, final door specification, and inspection hold point | Site work differs from the assumed material or edge condition | Approve conditionally with a drawing hold point |
| New-door preparation | The door is ordered or fabricated for this project | Current lock drawings incorporated into the door order | Late lock selection leaves the door incorrectly prepared | Use only with released dimensional data |
| Hold for alternate route | Thickness, material, or interface fails and no evidence closes the gap | Competing candidate evidence and project constraints | The schedule loses time while the gap remains unresolved | Move to another selection path |
An illustrative project may have one opening with a verified prepared mortise and another with an unknown core. Treating both as the same route would hide the weaker opening. Record each door or door type separately, even when they appear similar during a group walk-through.
For a broader comparison of field conditions and retrofit evidence, the Smart Lock Retrofit Site Survey provides a useful survey structure. The important distinction is between a survey that records uncertainties and a survey that converts uncertainties into assumed specifications.
Check the Frame, Swing, and Door Hardware
A lock can be correctly positioned within the leaf and still fail as an installed system if the frame or operating hardware conflicts with it. Inspect the frame rebate, stop, keeper, hinge movement, closer, hold-open arrangement, and any escape hardware associated with the opening.
| Outside-the-leaf check | What to observe | Effect on the SLK-9936S decision |
|---|---|---|
| Frame rebate and stop | Alignment, available depth, contact points | Can affect panel seating and latch engagement |
| Strike keeper | Fixing, alignment, movement, and contact with the latch | Can change the required faceplate or edge position |
| Door swing | Full travel, approach path, and collision points | Can affect latch operation and access workflow |
| Door closer | Mounting position, swing interaction, and permitted operating load | Can create latch or panel interference if not coordinated |
| Hold-open device | Mounting area, mechanism, and released position | May constrain the face, edge, or latch path |
| Escape hardware | Presence, movement, and overlap with lock components | Requires project-specific coordination |
CONFIRM-WITH-LOCAL-FIRE-EGRESS-ACCESSIBILITY-AUTHORITY: Verify fire-door, egress, accessibility, and access-control requirements for the specific opening with the authority or qualified reviewer responsible for the project location.
Record these observations as facts about the opening, not as assumptions about the lock. The supplied SLK-9936S record does not resolve frame clearances, closer forces, or escape-hardware arrangements. Those conditions belong in the site evidence and must be coordinated with the relevant door and hardware suppliers.
Use a Door Preparation Checklist at the Survey Handoff
The door preparation checklist below turns the survey into a procurement record. Each line should identify an observation, a measurement, or a drawing reference. A blank field means the item is open; it should not be converted into an assumed pass.
| ID | Preparation item | Required record | Evidence of completion |
|---|---|---|---|
| 1 | Door identifier | Project location, floor, room, and opening reference | Traceable survey label |
| 2 | Leaf material | Wood, metal, glass, aluminium, composite, or other construction | Material confirmed from site evidence |
| 3 | Leaf thickness | Reading at the lock position and supporting readings | Comparison with the current SKU record |
| 4 | Face layout | Scaled positions for mortise, cylinder, panel, and existing hardware | Marked face drawing |
| 5 | Hinge and handing | Hinge side and opening direction | Site survey entry |
| 6 | Mortise case | Dimensions, fixing points, condition, and center position | Comparison with current lock drawings |
| 7 | Cylinder | Bore, center, collar, and orientation | Dimensional evidence or installation detail |
| 8 | Faceplate | Plate outline, edge distance, fixing positions | Drawing comparison |
| 9 | Latch and keeper | Latch position, keeper alignment, and frame clearance | Interface inspection record |
| 10 | Panel area | Available width, height, and flat usable surface | Measured face drawing |
| 11 | Door hardware | Closer, hold-open, signage, reader, and escape-hardware positions | Coordination record |
| 12 | Preparation method | Work scope, responsible party, and inspection hold point | Released project instruction |
| 13 | Current documents | Dated product page, dimension drawing, guide, and datasheet revision | Document register |
The checklist should close with a signed disposition for every opening: approved fit, conditional fit pending named evidence, hold for clarification, or move to another route. Use the same disposition language in the site report, quotation request, and purchase order so that each party works from the same version.
Request Drawings Instead of Guessing Missing Dimensions
Make a dimension drawings request that identifies the exact SKU, project, door types, and unresolved site questions. The supplied record states that dimension drawings, an installation guide, and a full datasheet are available on request. The request should identify which document is needed for each decision.
A useful request packet contains:
- The current dimensional drawing for the SLK-9936S, including its revision date.
- Escutcheon, mortise case, cylinder, faceplate, keeper, and latch details.
- Applicable door thickness, material, handing, and preparation instructions.
- The installation guide covering door preparation and operational checks.
- A full datasheet matching the quoted configuration.
- A written response identifying any options or constraints for the submitted door types.
For line-by-line interpretation of the existing specification fields, use SLK-9936S Explained: Reading the Product Data Sheet Line by Line. That review should still be paired with current project documents rather than treated as a final fit certificate.
Include the site drawing in the request. “Will it fit?” is too broad for a supplier response, while “Does the current mortise and faceplate arrangement match the issued SLK-9936S preparation drawing for these measured wooden doors?” identifies a question that can be answered and recorded.
Use a Decision Matrix Instead of a Yes-or-No Guess
The final comparison should separate hard gates from evidence quality. A complete set of drawings can support approval only after the leaf and interface gates pass; a complete set of drawings cannot expand the listed thickness range.
| Decision stage | Pass condition | Conditional condition | Fail or hold condition |
|---|---|---|---|
| Leaf gate | Thickness and material are consistent with the current SKU record | A minor measurement question is assigned to the supplier | Thickness is outside the published range or material is unresolved |
| Interface gate | Mortise, cylinder, faceplate, latch, and keeper match issued drawings | One named item remains under review | The existing mortise or frame arrangement is incompatible and cannot be modified |
| Frame gate | Latch, panel, swing, and hardware operate together without conflict | Coordination is required before installation | A required adjustment has no approved work method |
| Documentation gate | Current drawing, guide, and datasheet are attached | A document revision is pending | No dimensional evidence is available for the selected configuration |
| Procurement gate | Door schedule and preparation instruction use the same SKU and revision | Approval is tied to a written condition | Procurement proceeds on an assumed or replaced specification |
Four outcomes are available. Approve fit means all gates pass against current evidence. Conditional approval permits budget or project planning while a named document or field check remains open. Hold means the opening may be viable but lacks enough evidence for release. Reject this route means the opening fails a gate and the project should evaluate another lock or door preparation path.
Make the outcome visible in the opportunity record. A conditional approval should name the evidence, owner, and required date; it should not use vague wording that allows the condition to disappear during ordering.
Verify Fit Again at Installation Handoff
Installation is a second fit assessment because the actual prepared opening can differ from the surveyed door. The installer should compare the released drawing with the delivered door before cutting or modifying anything. A successful credential test proves only that the lock powers and reads a card; it does not prove correct geometry.
| Handoff check | Test | Acceptance basis |
|---|---|---|
| Prepared geometry | Compare mortise, faceplate, latch, and panel positions with released drawings | Current SLK-9936S drawing and approved preparation method |
| Door operation | Open and close through the normal operating range | No unintended panel, latch, closer, or frame interference |
| Mechanical override | Operate emergency access using the approved procedure | Manufacturer instruction and project procedure |
| Card presentation | Test issued cards against the recorded read range | The first-party block lists 0–5 cm and less than 0.25 seconds; confirm on the dated product page for the specific SKU |
| Record capture | Confirm that the expected unlock event appears in the management workflow | Approved software and card-issuance configuration |
| Final documentation | Attach installed-door photographs and exception record | Project quality file |
The card and software assessment is developed further in SLK-9936S: Card, Code, Biometric and App Options Compared. Keep that comparison connected to, but separate from, the mechanical acceptance check so a credential option cannot mask a door-preparation defect.
The Procurement Answer and the Next Release Step
The slk 9936s door fit notes support a practical answer: the SLK-9936S is a credible candidate for a hotel wooden or metal door within the listed 36–100 mm range, but fit is not proven until the mortise, cylinder, latch, panel, frame, handing, and preparation method have been checked against current drawings.
The same question is worked through in more detail in what smart lock is best for wooden doors. That is the same question slk 9936s door fit notes has to answer here.Before releasing the order or preparation work:
- Attach the measured door schedule and a scaled face drawing.
- Confirm the current SKU page and issue the dimension drawings request.
- Compare the mortise, 5-pin mortise cylinder, faceplate, keeper, and 3-point latch details.
- Record frame, swing, closer, hold-open, and escape-hardware conditions.
- Mark each opening as approved, conditional, hold, or another route.
- Carry the final drawing revision and exceptions into the purchase order.
For the commercial control step, use SLK-9936S: Ordering SLK-9936S: What to Lock Down on the Purchase Order so the approved configuration, documents, preparation obligations, and unresolved conditions travel with the order.
A project-ready fit is therefore not the result of matching a model photograph to a door photograph. It is the result of a documented SLK-9936S door preparation decision, backed by current drawings and a site-specific door preparation checklist. When those records are complete, request a project quotation with the SKU, door types, measured dimensions, and drawing revision attached for review.

